Diapro T?bbi Ürünler Across System User manual

Incubator
Version 1.0


Foreword
Thank you for purchasing our Products: Card Incubator , This
Manual for users contains function and operation of the Instrument.
In order to use the instrument properly, please read this manual
carefully before using the Instrument.
Opening Check
Please check the Instrument and Appendix with the packing list
when you first open the instrument packing case. If you find there
is something wrong with the Instrument and the Appendix, do
contact the vendor or the producer.


Contents
1. Introduction………………………………………………......1
1.1 Delivery package…………………………….…………….1
1.2 Structure Description………………………………….......2
1.3 Installing the device………………………………….…....3
2. Technical data……………………………………………….4
3. Safety precautions……………..……………………….......5
4. Operation guide..…………………………………………….6
4.1 Control elements……….…………………………………..6
4.2 Setting the timing time……... ..…………………………...6
4.3 Setting the temperature…………………………..……....6
4.4 Switching to the Fahrenheit display……………………..7
4.5 Start and Stop……………………………………………..7
4.6 Temperature calibration…………………………………..8
5.Maintenance and cleaning…………………………………10
6. Troubleshooting……………………………......................10
Annex 1 Wiring Diagram for Incubator ………………….11
Packing list………………………………………………….12


1 Introduction
This Incubator designed for workstations in training and research
laboratories in the fields of bioscience, medicine and chemistry.
Before starting up this incubator for the first time, please read the
rest of this operations manual.
1.1 Delivery package
Card Incubator 1pcs
Power line 1pcs
Operations manual 1pcs
1


1.2 Structure Description
2
Right Display
Panel
Power Switch
Power connector
lid
Left Block
Right Block
Left Display


1.3 Installing the device
1.3.1 Place the card incubator onto a level , horizontal surface.
1.3.2 Insert the column connector of the power line to power connector of
the device ,and insert another connector of the adapter to mains power
supply.
1.3.3 Power on the main switch. The incubator is ready to operate when
the display becomes visible.
1.3.4 Put the test card into the block, then close the lid.
3
AC220V


2 Technical data
Model K37-24
Power supply AC220V 22V 50Hz
Fuse 250V 3A 5X20
Power supply AC220V 22V 50Hz
Maximum Power 200 W
Temperature range 3550
Timing range 1sec 99min59sec
Accuracy of the temperature 0.5
Display accuracy 0.1
Heating time
(from 20 to 37 )5min
Ambient temperature 530
DimensionsWDH280mm380mm115mm
Weight 6.0 kg
4


3 Safety precautions
This product is a normal and an indoor Instrument.
5
Read the Manual carefully before operation, The expert of wiring
equipment can operate this Instrument.
The operator should not open or repair the Instrument by himself,
which will result in losing the qualification of repair guarantee or
occur accident. If there is some wrong with the Instrument, the
company will repair it.
The Instrument should be put in the place of low temperature, little
dust, no water and no sun or strong lamp. What’s more, the place
should be good aeration, no corrosively gas or strong disturbing
magnetic field, far away from central heating, camp stove and
other hot resource. Don't put the Instrument in wet and dusty place.
Mains switch is on the rear of the device, push “I” to pow
er on the device, and push “O” to power off the device.
Power off when you finish your work. Pull off the connector plug when
there’s long time no use of the Instrument and cover it with a cloth or
plastic paper to prevent from dust.




4. Operation guide
4.1 Control elements
4.2 Setting the timing time
press “” or “” key at the left ,you can set the timing time from 1sec to
99min59sec for the left block. And you can press “” or “”key at the
right ,set the timing time for the right block too.
6
4.3 Setting the temperature
The default setting value of the block is 37.0

,if you need other
temperature. For example, you need the temperature of the left block is 40

,
you can press left “START/STOP” key and left “” key simultaneously.
When press “” or “” key, the units digit will
flicker, then you can modify the timing time, About 6
seconds, the flicker will disappear, exit setting
interface.
Then the units digit will flicker,
you can press “” or “” key to
modify the temperature, About 6
seconds, the flicker will
disappear, exit setting interface.
Temperature
of left block
Time of left
block
Start/stop
the left timer
Setting time
of left block
Temperature
of right block
Time of right
block
Start/stop the
right timer
Setting time
of right block
