DIEX DXFS6 User manual

Thank you for purchasing our products. Be sure to read the manual, it is important to
better understand the product to make the most of it.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
1. GENERAL INFORMATION
DIEX manufactures a range of antennas designed and produced to give top performance and reliable
long lasting service. They are completely manufactured of non-corrosive materials. The antennas come
partly factory-assembled in order to facilitate and expedite your labor.
1.1. Introduction and Description
This manual explains how to assemble the DIEX DXFS series. The DXFS6 is a bidirectional
antenna that covers the VHF spectrum between 50 - 54 MHz (tunable).The power input limit is 2000w
pep.
1.2. Owner Assistance
If assistance or service is needed, your local dealer should be contacted first. In the unlikely event, you
need further information you may get in touch with DIEX by email.
e-mail: [e-mail]
1.3. Specifications
1.4. SAFETY FIRST!
Get acquaint with and observe strictly the requirements and instructions of your local legislation. Direct
grounding of the antenna and the tower structure is essential as protection from lightning strikes and
static electricity. The entire earth-connection system must meet your local standard requirements.
Do not install the antenna close to power lines and cables, as their proximity, arc-over or contact with
them during assembly, installation, and exploitation is hazardous and can be lethal.
Do not work alone! You must have at least one assistant always when you work on the antenna. If you
have any doubt concerning the safety, please consult your dealer or engage a professional company.
1.5. Location
The antenna should be mounted on a support tower structure at a height between 5 and 10 meters (16 -
33ft) above the ground level. It must be located in the clear, away from trees, power installations,
buildings, other antennas etc. Such objects can be dangerous and they can reduce the antenna efficiency
or cause interference. If metal guy wires are used for the tower, they should be broken electrically with
strain insulators, at 1,5 meters (4/5 ft) apart or less.
1.6. Your first steps
The first step to installation is to fully read this manual. Then, carefully inspect the shipping cartons for
any physical damage. DIEX ships antennas in highly protected containers, but it cannot assure that
MODEL
DXFS6
BAND
6 M
GAIN
2,4 DBI
2:1 SWR BANDWIDTH
+ 500kz
MAX. INPUT PWR
2000 W PEP
>ELEMENT
290 cm
TURNING RADIUS
150 cm
MAST DIAMETER
1 1/4" TO 2"
WIND-LOAD AREA
0,03 m2
WEIGHT
1 Kg

mistreatment by shippers will not occur. If there is any such damage, notify your DIEX dealer immediately.
Failure to do so may invalidate your warranty.
Select a large and clear area to assemble the antenna.
The DIEX production uses metric (European) system of measurement units.
2. ASSEMBLING
Aprox. 136,5 cmAprox. 136,5 cm
1
+
-
2.1- Installing insulator (TB) on the support (SP) Figure 1.
Figure 1
2.1 - Fix the U clamps on the support (SP) with the insulator (TB) which should be as
shown in Figure 2 -3.
Figure 2 - 3
2.2 - Enter the element (1) in insulators and lock with screws (PS) at the top of the
insulator.

2.2.1 - Place the contact screws (PC) as shown in figure 4.
Figure 4
2.3 - Assembling the elements.
2.3.1 - The total length should be around 2.85m, small adjustments may be necessary.
2.3.2 - Place the element 2 inside the element 1. The element is adjustable with the
clamp to the desired frequency;
2.4 - Connecting the coaxial cable to the antenna.
2.4.1 - Separate the center of the cable loop about 15 cm and solder the terminals (TM),
connect the in the element has no side seal well to prevent water from entering rain on
the cable.
2.5 - Finishing the installation.
2.5.1 - Place the clip U in support as Figure 5 and install in mast in Maximum 40mm,
attach the cable to the mast leaving off to avoid traction on the terminals.
Figures 5

2.5.2 - Install the antenna as high as possible and free from obstacles, other antennas,
walls, etc. For optimal performance and good SWR, install at least 3 m from the antenna
base.
3 - Adjusting SWR
3.1 - With the antenna mounted and installed in the correct place, check SWR.
3.2 - Normally, adjustments are not necessary, however, if you notice that the swr is
above 2:1 at the frequency you are going to use, it will be necessary to adjust.
3.3 - First it is necessary to find the point that the antenna is resonating with the best
swr, use a good meter or the meter of the radio itself to measure.
3.4 - If the frequency found with the smallest swr is below the desired frequency,
decrease the antenna 1cm at a time on both sides and measure again and repeat until
you reach where you want.
3.5 - If the frequency found with the smallest swr is above the desired frequency,
increase the antenna 1cm at a time on both sides and measure again and repeat until
you reach where you want.
The contents of this manual are subject to change without notice.
WARRANTY
Diex antenna products are guaranteed for One year against manufacturing defects, Diex may repair or
replace parts or all of the product at its own discretion within the warranty period. Damage caused by
lightning, falling, forces of nature, misuse, installation by an unqualified person, i.e., improper, negligent or
incorrect assembly is not covered by the warranty.
Products that undergo any adaptation or alteration or repairs by unauthorized service automatically void
the warranty.
Manual DXFS6 fe
Rua Almirante Lobo 310 –Ipiranga –São Paulo –SP –Brazil
TELEPHONE: [phone] –Whatsapp/Telegram –E-mail: die[email protected]