Digilin Vega User manual

©2021 Digilin Technologies
Document Rev: 1.0 - 11 August 2021
Product specifications are subject to change without notice.
Vega
Fibre Optic Lightsource
User Manual

Vega - Fibre Optic Lightsource
User Manual
1.0 - 11 August 2021
digilin.com.au Page 2 of 4
[phone]
Table Of Contents
Notes.....................................................................................................................................................................................................................................................................................................2
Introduction..................................................................................................................................................................................................................................................................................2
Specifications .............................................................................................................................................................................................................................................................................3
Physical.......................................................................................................................................................................................................................................................................................3
Inputs............................................................................................................................................................................................................................................................................................3
Optical.........................................................................................................................................................................................................................................................................................3
Installation ......................................................................................................................................................................................................................................................................................3
Mounting .................................................................................................................................................................................................................................................................................3
Using Mounting Plate.......................................................................................................................................................................................................................................3
Without Mounting Plate...............................................................................................................................................................................................................................3
Fibre ...............................................................................................................................................................................................................................................................................................4
Wiring...........................................................................................................................................................................................................................................................................................4
Operation.........................................................................................................................................................................................................................................................................................4
Dimming....................................................................................................................................................................................................................................................................................4
Scintillation Wheel Speed...................................................................................................................................................................................................................................4
Appendix A –Troubleshooting .............................................................................................................................................................................................................................4
Notes
•Install in a dry sheltered position
•Interior use only
•Ensure adequate ventilation
•Installation should only be performed by a qualified professional
•Install in accordance with all appropriate wiring standards
•TYPE Y ATTACHMENT: If the external flexible cable or cord of this luminaire or associated
PSU/driver is damaged. It shall be exclusively replaced by the manufacturer or his service agent or a
similar qualified person to avoid a hazard.
•The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer
than 0.33 m is not expected.
•Lightsource is not mains dimmable.
Introduction
With a long lamp life, and very bright white light output, the Vega fits perfectly in situations where
tungsten halogen, or even metal halide options would normally be specified. Very cool and almost silent
running combined with a small unit size, make this light source suitable for use in restricted spaces. Fitted
with a standard 30mm fibre port connector, this light source is suitable for both new installations and retro-
fitting to existing fibre optic installations.

Vega - Fibre Optic Lightsource
User Manual
1.0 - 11 August 2021
digilin.com.au Page 3 of 4
[phone]
Specifications
Physical
U n i t s
Dimensions
156 x 160 x 120
mm
Weight
1.35
kg
IP Rating
20
Ambient Temperature
-10 to 45
°C
Fibre Port Diameter
30
mm
Inputs
U n i t s
Voltage
24
VDC
Current
0.75
A
Optical
U n i t s
CCT
4000
K
Lumens
1820
lm
Effects Wheel
Scintillation
Installation
Mounting
• Do not locate this luminaire closer than 200mm from any flammable surface.
•It is imperative that a gap of 200mm is left around the unit. This is to allow air to circulate and
prevent overheating. The location must have free ventilation and must not have an ambient
temperature higher than that specified for the luminaire.
Using Mounting Plate
1. Invert light source and remove the screws holding the 4 rubber feet in place. Leave rubber feet in
place
2. Align the plate against the feet and secure ti using the 4 screws removed in step 1.
3. Secure the fitting to the desired mounting surface using suitable fasteners.
Without Mounting Plate
Simply locate the light source on a flat surface with adequate ventilation.

Vega - Fibre Optic Lightsource
User Manual
1.0 - 11 August 2021
digilin.com.au Page 4 of 4
[phone]
Fibre
1. Loosen the locking screw so it no longer
protrudes into the fibre optic port.
2. Slide the fibre optic common end into the
fibre port.
3. Tighten the locking screw to secure the
common end in place.
Wiring
Unit is supplied with a 24VDC supply.
1. Connect jack into socket on rear of
lightsource.
2. Plug the power supply into electrical
supply. Power indicator should now
illuminate.
Operation
Units begins operating once power is properly
connected.
Dimming
Light level can be manually dimmed using the knob on the rear of the lightsource.
Scintillation Wheel Speed
Motor rotation speed can be manually adjusted using the knob on the rear of the lightsource. Adjustment
range is from stopped to approximately 4RPM.
Appendix A –Troubleshooting
P r o b l e m
P r o b a b l e C a u s e
Remedy
Unit is dead –no light output and
LED power indicator on PSU is not
illuminated
Mains supply off
Check supply & reinstate
Loose mains plug
Check plugs
PSU failed
Replace PSU
Unit is dead –no light output and
LED power indicator on PSU is
illuminated, but LED indicator on
Light source not illuminated
PSU failed
Replace PSU
Poor light output on fibre
Lightsource dimmed
Check and increase dimmer settings
as appropriate
LED driver failure
Replace light source
Unit is dead –no light output but
LED power indicator is illuminated
Dimming control at minimum
Adjust brightness on dimmer control
at rear
LED array or drive failure
Replace light source
Power Jack
Power Indicator