Digipressure DPC_ HL-DIF Series Manual

URL http:// www.digipressure .com
E-Mail :[e-mail] FAX : [phone]
TEL : [phone]
Address: 414. KoFoMotechno center 1289-5.Jeongwang-dong ,Siheung, Kyeonggi-Do Korea 429-450
DIGIPRESSURE
DPC_ HL-DIF SETTING MANUAL
DISPLAY 3DIGIT FND * 2 HP/LP
TYPE HL TYPE (OPTION : HL-DIF, L YTPE)
ACCURACY ±1%F.S
BURST PRESSURE 100Kgf/cm2g
TEMPERATURE -20 ~ 60 ℃
HUMIDITY 0 ~ 80% R.H
APPLICATION GAS Air, Inert gas, Water, Oil, Others
SENSOR MATERIAL Ceramic Diaphragm
PROCESS 7/16 - 20UNF
PRESSURE RANGE HP -1.0 ~ 50Kgf/cm2g, LP -1.0 ~ 50Kgf/cm2g
CONTROL OUTPUT 3Point Relay Output(CONTACT: 250V/3A SPDT)
POWER SUPPLY AC220V±10%50/60Hz0.2A(Option:380V.110V)
ACCESSORY Mounting Bracket
WEIGHT Approximately 510g
CASEMATERIALS ABS
INTERFACE RS-485
Connection with Power 220V
Connection with Power 220V
Low Pressure S/W : COM ,NC, NO
Low Pressure S/W : COM ,NC, NO
High Pressure S/W : COM, NC ,NO
High Pressure S/W : COM, NC ,NO
differential pressure S/W : pressure S/W :
COM ,NC.NO
COM ,NC.NO

DIGIPRESSURE
DPC-HL SETTING METHOD
HPS
HPS
설
설정 정
HPS Input the setting value of high pressure
by pressing the button, to operate
alarm (26.0Kgf/cm2)
URL http:// www.digipressure.com
E-Mail :sales@digipressure .com FAX : [phone]
TEL : [phone]
Address: 414. KoFoMotechno center 1289-5.Jeongwang-dong, Siheung, Kyeonggi-Do Korea 429-450
Press 2buttons for 2 seconds simultaneously, and then the settin
Press 2buttons for 2 seconds simultaneously, and then the setting mode fixed. g mode fixed.
LPS
LPS
설
설정 정
LPS Input the setting value of low pressure
by pressing the button, to operate
alarm (3.5Kgf/cm2)
LIF
LIF
설
설정 정
LIF Input the differential value of LPS
by pressing the button
(2.5Kgf/cm2)
Ldt
Ldt
설
설정 정
Ldt Input a delay time against output on the
status of low pressure by pressing
the button (0 ~100 sec)
H
H- -A A
설
설정 정
H-A Select the return mode with buttons
H: Hold (Manual) operation
A: Automatic operation
Add
Add
설
설정 정
Add Select the address by pressing the
button (0~255) for communication
by RS-485
End
End
설
설정 정
Press any button, and then the operation ends with
beep sound. If not, it returns to
the reset mode automatically
after 20 seconds.
SET L
SET L
설
설정 정
Press buttons for 3seconds at the same time
for correcting value of pressure to
fit ZERO“Never use while operating”
dPS
dPS
설
설정 정
DPS Input the differential value of dual
compressors by pressing button
to operate alarm (5.0 Kgf/cm2)
ddt
ddt
설
설정 정
ddt Input a delay time to operate alarm
for differential value by pressing
button(0 ~ 100 sec)
ddc
ddc
설
설정 정
ddc Input the type of differential pressure
“0”+ dp “1”-dp“2”±dp
(“0”, ”1”, ”2”)