DigiSender DGXDSDV112 User manual

Model: DGXDSDV112
Single Input HDMI AV Sender System
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video

Page 02 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Contents
Introduction 03
Installing your DigiSender® XD HDMI 04 - 10
Step 1 - Unpack your DigiSender® XD HDMI 04
Step 2 - Install the Transmitter 05
Step 3 - Install the IR Systeme Technik™ Remote Relay Kit 06
Step 4 - Install the Receiver 07
Step 5 - Test Your Setup Using the Test Mode 08-10
Using your DigiSender® XD HDMI 11 - 12
Standard Operation 11
Re-Syncing the Transmitter and Receiver 12
Troubleshooting 13 - 14
Frequently Asked Questions 13
Technical Support 14
For indoor use only. Do not expose the transmitter or receiver units
to moisture as this may lead to faulty operation and risk of electric
shock.
Risk of electric shock, do not open. None of the contents of this
DigiSender®pack contain user-serviceable parts.
Avoid dripping or splashing liquids on the transmitter or reciever and
do not place objects lled with liquid on them.
The transmitter and receiver rating labels are located on the base of
the units.

Page 03Please read the instructions carefully prior to installation
Introduction
Congratulations on purchasing the new DigiSender® XD HDMI from AEI Security & Communications
Ltd. This product represents the absolute pinnacle of state-of-the-art wireless audio video distribution
technology, at exceptional value for money.
You can now enjoy DVD quality video and Hi-Fi stereo sound from your Satellite, Cable, DTV, DVD, DVR
or VCR in another room in your home, without the worry of interference from other wireless products.
Its use of spread spectrum digital technology means that signals will not only pass through walls and
ceilings effortlessly, but that the signal will not degrade or be affected by interference from similar
wireless devices. In fact, this technology coexists so seamlessly with other wireless technologies, that
it can be set up and run right next to a wireless router or microwave, something that has never before
been possible.
With innovative features like HDMI throughpass, the IR Systeme Technik™ Remote Relay Kit and a
Test Mode you can rest assured that you have purchased one of the most advanced video sender
systems available on the market today.
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System

Page 04 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Installing your DigiSender® XD HDMI
Step 1 - Unpack your DigiSender® XD HDMI
All DigiSender® orders are computer weight checked when packed. However, it is a good idea to check
all kit contents are present before proceeding with the installation.
POWER
Transmitter
POWER
Receiver
IR Systeme Technik™ Kit 2x Power Supply Units
2x HDMI Cables

Page 05Please read the instructions carefully prior to installation
Use one of the included HDMI cables and connect
it to the socket labelled ‘HDMI OUT’ on the back
of the DigiSender® Transmitter and the HDMI input
on your TV.
2.
Locate the HDMI cable that goes from your Satellite
receiver or Cable box to your TV. Unplug the HDMI
cable from the back of your TV, and connect it to
the socket labelled ‘HDMI IN’ on the back of the
DigiSender® Transmitter.
1.
Installing your DigiSender® XD HDMI
Step 2 - Install the Transmitter
The DigiSender® Transmitter will send the audio and video from a connected source (your Satellite
Receiver for example) to the Receiver, located in another room in your home.
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Connect the IR Emitter to the socket labelled ‘IR’ on
the back of the DigiSender® Transmitter. See Page
06 for more information on installing the IR Systeme
Technik™ Remote Relay Kit.
3.
Connect the Power Supply Unit (PSU) to the socket
labelled ‘PSU’ on the back of the DigiSender® Trans-
mitter and plug it into an available mains socket.
The Power Indicator will light up Red to indicate that
the unit is in Standby Mode.
4.

Page 06 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Installing your DigiSender® XD HDMI
Step 3 - Install the IR Systeme Technik Remote Relay Kit™
The IR Systeme Technik™ Remote Relay Kit includes various accessories that will help you in setting it
up the Remote Relay system correctly.
Once set up, this Remote Relay system will enable you to control your source equipment (your Satellite
receiver for example), with its remote control, from the receiving location.
Example 1: Mount the IR Emitter vertically using
accessories 1 and 2. Ensure the LED is facing the IR
sensor on your source equipment.
Example 2: Mount the IR Emitter horizontally using
the supplied sticky pad. Ensure the LED is facing the
IR sensor on your source equipment.
Extension Pieces
Accessory #1
Accessory #2
IR Emitter

Page 07Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Connect the Power Supply Unit (PSU) to the socket
labelled ‘PSU’ on the back of the DigiSender® Re-
ceiver and plug it into an available mains socket.
The Power Indicator will light up Red to indicate that
the unit is in Standby Mode.
2.
Use one of the included HDMI cables and connect
it to the socket labelled ‘HDMI OUT’ on the back of
the DigiSender® Receiver and the HDMI input on
your receiving TV.
1.
Installing your DigiSender® XD HDMI
Step 4 - Install the Receiver
The DigiSender® Receiver will pick up the signals being sent by your DigiSender® Transmitter and
output them to a connected TV, located in another room in your home.

Page 08 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Installing your DigiSender® XD HDMI
Step 5 - Test your Setup Using the Test Mode
Your DigiSender® XD HDMI is set to Test Mode by default and will aid you in getting the best possible
picture and help identify any problems that may arise during installation.
Turn on the receiving TV, and select the HDMI chan-
nel assigned to the HDMI Input that you plugged
the DigiSender® Receiver in to. This may be labelled
as SOURCE, INPUT, AUX, AV, VIDEO, VCR or .
4.
Switch on the source equipment (Satellite, Free-
view, DVD, VCR, etc.).
1.
Turn on the DigiSender® Transmitter by pushing the
Power button on the front of the unit. The Power
Indicator will change from Red to Green to indicate
that the unit is switched on.
2.
Turn on the DigiSender® Receiver by pushing the
Power button on the front of the unit. The Power
Indicator will change from Red to Green to indicate
that the unit is switched on
3.

Page 09Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
continued...
You will notice that at the top right corner of the
screen is a blue Test Bar with some information on
it. If the Test Bar is not present, then the DigiSender®
Receiver may not be in Test Mode. Turn the Di-
giSender® Receiver off, flick the Mode Switch on the
back from Normal to Test and then turn the Receiver
on again.
7.
The DigiSender® XD HDMI Boot Screen will be dis-
played whilst the DigiSender® Transmitter and Re-
ceiver synchronise.
5.
After approximately 5 seconds the picture will
change to whatever you are transmitting. If the pic-
ture does not change, or changes to a Test Card, you
may need to re-sync the DigiSender® Transmitter and
Receiver. See page 12 for more details.
6.
The first number indicates the Frame Rate that the
DigiSender® Receiver is picking up from the Trans-
mitter and outputting to your TV.
8.

Page 10 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
continued...
Note: When switching from Test Mode to Normal mode, or vice versa, it will be necessary to turn the
unit off and then back on again.
Having made any necessary adjustments to the po-
sitioning of the units and/or aerials, flick the Mode
Switch from Test to Normal and turn the unit off.
Installation is now complete!
12.
The second number indicates Frame Loss. This
is the percentage of Frames that are not getting
through to the DigiSender® Receiver correctly. If you
are getting high Frame Loss you may need to adjust
the positioning of the units and/or aerials.
9.
‘P’ means that the picture quality should be good,
with the Frame Rate remaining steady at around
25. ‘F’ means that you may notice subtle losses in
picture quality due to Frame Loss. Try adjusting the
positioning of the units and/or aerials.
10.
The last icon indicates Signal Level. This is key to a
good Frame Rate and low Frame Loss. Endeavour to
keep this as high as possible. If you are getting a low
Signal Level, you may need to adjust the positioning
of the units and/or aerials.
11.

Page 11Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Using your DigiSender® XD HDMI
Standard Operation
Turn on the receiving TV, and select the HDMI chan-
nel assigned to the HDMI Input that you plugged
the DigiSender® Receiver in to. This may be labelled
as SOURCE, INPUT, AUX, AV, VIDEO, VCR or .
4.
Switch on the source equipment (Satellite, Free-
view, DVD, VCR, etc.).
1.
Turn on the DigiSender® Transmitter by pushing the
Power button on the front of the unit. The Power
Indicator will change from Red to Green to indicate
that the unit is switched on.
2.
Turn on the DigiSender® Receiver by pushing the
Power button on the front of the unit. The Power
Indicator will change from Red to Green to indicate
that the unit is switched on
3.

Page 12 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Turn on both the DigiSender® Transmitter and Re-
ceiver.
1.
Press and hold the ‘Pair’ button on the back of the
DigiSender® Transmitter and Receiver, simultane-
ously, for 5 seconds and then release.
2.
Should you need to re-sync the DigiSender® Transmitter and Receiver at any point, this can be achieved
by following the instructions below.
Using your DigiSender® XD HDMI
Re-syncing the Transmitter and Receiver
Please note that because you need to hold the ‘Pair’ Button on the DigiSender® Transmitter and Receiver
simultaneously, you will need to have both units in the same room as each other and within reach. Al-
ternatively, if you have someone that can help, they can hold the Transmitter ‘Pair’ button in the lounge
while you hold the Receiver ‘Pair’ button in the bedroom.

Page 13Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Troubleshooting
Frequently Asked Questions
Q. I can only watch the same channel as the lounge, is that right?
A. That is correct. This is because your Satellite receiver, Cable box or Freeview box is only able to
output one channel at a time.
Q. The Remote Relay is intermittent or not working, how can i fix it?
A. Most of the time this is due to one of two things:
1. Make sure the IR Emitter cable does not run directly under or over your source equipment. Most
Satellite receivers, Cable boxes and Freeview boxes have built-in Hard Disk Drives that can put out
quite a bit of Electro Magnetic Interference when in use.
2. Ensure that the IR Emitter is positioned correctly. It should be positioned with the face of the IR
Emitter pointing directly at the IR Sensor on your Satellite receiver, Cable box or Freeview box.
2” - 4” away is usually best. It is often easiest to set up the Remote Relay system with the aid of a
friend. Get them to try and change channels from the receiving location, while you wave the IR
Emitter around in front of the source equipment. When either of you see the channels change, you
know that is the right place for the IR Emitter.
Q. My picture is jerky, how can I solve this?
A. This is an indication of poor Frame Rate. Put the system into Dignostics Mode (see page 08 - 10) and
check the Signal Level. Try adjusting the position of the antenna on both the DigiSender®
Transmitter and Receiver whilst another person monitors the Signal Level.

Page 14 Please read the instructions carefully prior to installation
DGXDSDV112 - DigiSender® XD HDMI - Single Input HDMI AV Sender System
Troubleshooting
Technical Support
AEI Security & Communications Ltd is dedicated to providing our customers with first class customer
care and technical support.
1. Website
Free technical advice is available online 24/7 at our dedicated support web site: www.aei.eu
2. Online Videos
Watch online Installation and Troubleshooting Video Guides at: www.aei.eu/video
3. Email
Email our technical department directly at: [email protected]
4. Live Chat
Chat to one of our technical advisors live. See website for details.
5. Telephone
We have a dedicated helpline, open Monday to Friday, 9AM - 5PM. Call 01797 226123
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video

DECLARATION OF CONFORMITY
01022007/01/DG-DV-DX
We,
AEI Security & Communications Ltd.
Weslake Industrial Park, Harbour Road, Rye, East Sussex, TN31 7TE, United Kingdom
declare under our sole responsibility that the products bearing the series code prefixed:
DGx, DVx, DXx (x refers to the specific model number)
are in conformity with the essential requirements of Directive 1995/5/EC. These products have been tested against the following
standards and specifications:
Low Voltage Directive
EN60950:2000 Safety of information technology equipment.
Electromagnetic Compatibility Directive
EN 301 489-3 V1.3.1: 11-2001 Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 KHz
and 40 GHz.
EN 301 489-1 V1.3.1: 09-2001 Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical
requirements.
Radio Spectrum
EN 300 440-1 V1.3.1: 09-2001 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices;
Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 1: Technical
characteristics and test methods.
Power Supply
EN55022: 2003 Information technology equipment. Radio disturbance characteristics. Limits and methods
of measurement.
EN55024: 2003 Information technology equipment. Immunity characteristics. Limits and methods of
measurement.
IEC 61000-3-2: 2001 Electromagnetic Compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current
emissions (equipment input current <= 16 A per phase).
IEC 61000-3-3: 2001 Electromagnetic Compatibility (EMC) - Part 3-3: Limits - Limitations of voltage changes,
voltage fluctuations and flicker in public low-voltage supply systems, equipment with rated
current <= 16 A per phase and not subject to conditional connection.
The product is marked with the CE marking and Notified Body Number according to directive 1999/5/EC.

Transmitter Connections
Receiver Outputs
HDMI version
HDCP
Operating Frequency
Remote Control Compatiblity
Audio Input Level
Audio Bandwidth
Range
Power
Dimensions
Weight
1x HDMI Input, 1x HDMI Output
1x HDMI
1.3
Compliant
2.4GHz Digital
RC5, RC6
1.0v PP (Mod 1KHz, Dev 15KHz)
20Hz - 22KHz (-3dB)
150m (clear line of sight)
5V DC, 1.0A
L: 90mm, W: 140mm, H: 25mm
0.23kg
SPECIFICATIONS
CW140812-3
© 2012 AEI Security & Communications Ltd. All rights reserved.
Registered in England: 02831823
AEI Security & Communications Ltd
Weslake Industrial Park
Rye Harbour Road, Rye
East Sussex
TN31 7TE
United Kingdom
IR Systeme Technik and its logo are trademarks of AEI Security & Communications Ltd.
DigiSender is a registered trademark of AEI Security & Communications Ltd.