Digital Projection E-Vision 5100 Series Operating manual

Rev B September2020
E-Vision Laser 5100 Series
IMPORTANT INFORMATION
120-557B

DigitalProjection E-Vision Laser5100 Series
Rev B September2020
page 2
Important Information
This page is intentionally left blank

Contact Information DigitalProjection E-Vision Laser5100 Series
Contact Information
China
Digital Projection China
中国 北京市 朝阳区 芍药居北
里101号 世奥国际中心A座2301
室(100029)
Rm A2301, ShaoYaoJu 101 North
Lane, Shi Ao International Center,
Chaoyang District, Beijing 100029,
PR CHINA
Tel: [phone]
Fax: [phone]
[e-mail]
www.dp-china.com.cn
North America
Digital Projection Inc.
55 Chastain Road, Suite 115,
Kennesaw, GA 30144, USA
Tel: [phone]
Fax: [phone]
[e-mail]
www.digitalprojection.com
Europe
Digital Projection Limited
Greenside Way, Middleton,
Manchester, M24 1XX, UK
Registered in England No.
2207264
Registered Office: As Above
Tel: [phone]
Fax: [phone]
[e-mail]
[e-mail]
www.digitalprojection.co.uk
Taiwan
Digital Projection Taiwan
186 Ruey Kuang Rd, Neihu
District, Taipei, 114 Taiwan
Tel: [phone] x8854
[e-mail]
Japan
Digital Projection Japan
〒105-0012 東京都港区芝大門
2-1-14
2-1-14 Shibadaimon, Minato-ku,
Tokyo, Japan 105-0012
[e-mail]
www.digitalprojection.com/jp
Dubai
Digital Projection FZE
Unit B4, Light Industrial Units 4,
Silicon Oasis, Dubai, UAE
Tel: [phone]
[e-mail]
www.digitalprojection.com
India
Digital Projection India
Plot-43, Sector-35, HSIIDC,
Gurgaon Haryana -122001
Tel: [phone]#4275
[e-mail]
Korea
Digital Projection Korea
1511, Byucksan Digital Valley 6-
cha, Gasan-dong, Geumcheon-
gu, Seoul, Korea
Tel: [phone] #1417
[e-mail]
Important Information Rev B September2020
page 3

DigitalProjection E-Vision Laser5100 Series Contents
Contents
Contact Information 3
Contents 4
Symbols used in this document 5
Additional Documentation 5
Electrical and Physical Specifications 6
Laser Precautions 7
Projector 7
Laser Parameters 7
Remote Control - Laser Pointer 8
Laser Pointer Parameters 8
Location of Laser Aperture 9
Interlock Switches 10
General Precautions 11
Installation Precautions 12
Product Labels 16
Projector 16
Remote Control 17
Label Locations 18
Operation and Configuration Precautions 20
Compliance with International Standards 21
RF Interference 21
Noise 21
European Waste Electrical and Electronic Equipment (WEEE) Directive 21
What's in the box? 22
Basic Operating Instructions 23
Positioning the screen and projector 23
Connecting the power supply 23
Switching the projector on 24
Switching the projector off 24
Selecting an input signal 24
Selecting a test pattern 25
Adjusting the image 25
Orientation 25
Rev B September2020
page 4
Important Information

Contents DigitalProjection E-Vision Laser5100 Series
Geometry 25
Picture 25
Adjusting the lens 26
Control panel 27
Projector indicators 28
Remote control 29
Symbols used in this document
Some information in this document may be accompanied by the following symbols:
LASER WARNING: this symbol indicates that there is a potential hazard of eye
exposure to laser radiation unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical
shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself
and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should
read.
Additional Documentation
Full information about operating, connecting and setting up the projector can be found in the
User Guides.
Please use the QR code (also located on the projector) to access the latest E-
Vision projector user guides and other documentation via the Digital Projection
website.
Or visit the products specification page on the Digital Projection website to
download the latest user guide and other documentation.
Important Information Rev B September2020
page 5

DigitalProjection E-Vision Laser5100 Series Electricaland PhysicalSpecifications
Electrical and Physical Specifications
Mains Voltage 100-240VAC 50/60Hz 5.3A
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Operating Humidity 10% to 85% non-condensing
Storage Humidity 5% to 95% non-condensing
Dimensions L: 437.1mm (17.2in) X W: 360mm (14.17in) X H: 177.1mm (6.97in)
Weight 11Kg (24.2lb) including lens
Power Consumption at 100VAC: 500W typical (normal mode)
at 240VAC: 480W typical (normal mode)
Standby Power <2W (With LAN enabled), <0.5W (Without LAN enabled)
Thermal Dissipation at 100VAC: 1706BTU/Hour typical (Normal mode)
at 240VAC: 1638BTU/Hour typical (Normal mode)
Fan Noise 36dBA typical, 38dBA max (Normal mode)
Specifications are subject to change without notice.
Rev B September2020
page 6
Important Information

LaserPrecautions DigitalProjection E-Vision Laser5100 Series
Laser Precautions
Projector
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or reflected toward other people
or reflective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included
instructions are not followed.
Caution – use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Non-laser emission. There remains non-laser emission from the projection lens.
This portion of emission has been tested per IEC/EN 62471-5:2015 to be Risk Group
2 (low risk).
RISK GROUP 2 CAUTION. Possibly
hazardous optical radiation emitted from
this product. Do not stare at operating light
source. May be harmful to the eyes.
Laser Parameters
Wavelength 450-460nm (Blue)
Mode of operation Pulsed, due to frame rate
Pulse duration 1.34ms
Pulse repetition rate 120Hz
Maximum pulse energy 0.698mJ
Total internal power >100W
Apparent source size >10mm, at lens stop
Divergence >100 mili Radian
Important Information Rev B September2020
page 7

DigitalProjection E-Vision Laser5100 Series LaserPrecautions
Remote Control - Laser Pointer
CLASS 2 LASER PRODUCT
This Laser Product is designated as Class 2 during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not stare into the beam.
Do not view directly with optical instruments.
Do not point laser or allow laser light to be directed or reflected towards people,
animals, transportation or reflective objects.
Only allow use by responsible persons.
Keep out of reach of children.
This device is not a toy.
Laser Pointer Parameters
Wavelength 640-660nm
Max Output <1mW
Rev B September2020
page 8
Important Information

Location of Laser Aperture Digital Projection E-Vision Laser 5100 Series
Location of Laser Aperture
1
1. The laser aperture is located as
indicated below.
Be careful not to expose the eye to direct
laser light.
Important Information Rev B September2020
page 9

DigitalProjection E-Vision Laser5100 Series InterlockSwitches
Interlock Switches
1
Interlock switches are installed at the main
frame, inside the cover. These will power-off
the system individually when activated.
1. Will be activated when the top cover is
removed.
Rev B September2020
page 10
Important Information

GeneralPrecautions DigitalProjection E-Vision Laser5100 Series
General Precautions
The unit is never to be operated if the unit is defective or the cover or seal is
damaged.
No maintenance allowed by end user.
Do not open the cabinet. There are no user serviceable parts inside.
No service is allowed except by authorized personnel.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST
be earthed.
Take care to prevent small objects such as paper or wire from falling into the
projector. If this does happen, switch off immediately, and have the objects
removed by authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top
of the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged
power cable.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could cause a fire.
Always allow the projector to cool for 5 minutes before disconnecting the power or
moving the projector.
Never use strong detergents or solvents such as alcohol or thinners to clean the
projector and lens.
Important Information Rev B September2020
page 11

DigitalProjection E-Vision Laser5100 Series Installation Precautions
Installation Precautions
The projector must be installed only by suitably qualified personnel, in accordance
with local building codes.
The projector is heavy. Use safe handling techniques when lifting the projector.
Do not drop or knock the projector.
Do not install the projector close to anything that might be affected by its
operational heat, for instance, polystyrene ceiling tiles, curtains etc.
Place the projector in a dry area away from sources of dust, moisture, steam,
smoke, sunlight or heat.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air
temperature within the enclosure does not exceed operation temperature while the
projector is running, and the air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the
projector does not recycle exhaust air, as this may cause the device to shutdown
even if the enclosure temperature is with the acceptable operation temperature
range.
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
Keep your product away from fluorescent lamps (>1 Meter) to avoid malfunction
caused by IR interference.
Avoid installing near an air conditioner duct or a subwoofer.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in
an emergency.
Please pay attention to projector installation with respect to other staging laser light
equipment set-up. These systems can cause permanent damage to the DMD
imaging devices used in our projectors. This damage is not covered by our
warranty.
When using projectors in environments with third party high power laser systems
avoid direct laser beams pointing towards the projection lens. This may cause
incident light to converge into the optical engine and cause damage to the DLP
DMD.
Rev B September2020
page 12
Important Information

Installation Precautions DigitalProjection E-Vision Laser5100 Series
Before installation, make sure that the surface, ceiling or rigging that is to support
the projector is capable of supporting the combined weight of the projector and lens.
Backup safety chains or wires should always be used with ceiling mount
installations.
When installing a ceiling mount, make sure the weight limit is not exceeded and the
projector is firmly secured.
The projector can be operated any position, as shown in the diagram:
360˚
360˚
Tilt (Left) and Roll (Right)
Allow at least 50cm (19.7in) of space between the ventilation outlets and any wall,
and 30cm (11.8in) on all other sides.
Important Information Rev B September2020
page 13

DigitalProjection E-Vision Laser5100 Series Installation Precautions
Minimum 500mm
(19.69in)
Minimum 500mm
(19.69in)
Minimum 500mm
(19.69in)
Minimum 100mm
(3.94in)
Minimum 500mm
(19.69in) Minimum 300mm
(11.81in)
Example Positioning
Make sure the lens cap is removed from the lens before operating the projector.
Light energy levels have been known to cause damage to both the lens and
projector optics. This damage is not covered by our warranty.
Connect the LAN cable only to a computer LAN connection. Other similar
connectors may have a dangerously high voltage source.
A VGA IN connector should be used to connect to the VGA IN port on the projector.
It should be inserted tightly, with the screws on both sides securely fastened to
ensure proper connection of the signal wire for achieving optimal display effect.
An AUDIO IN connector should be used to connect to the AUDIO IN port on the
projector. It CANNOT be connected to AUDIO OUT otherwise, it will lead to mute
output and even DAMAGE the port.
The power cord and signal cable should be connected before the projector is
powered on. During startup and operation, DO NOT insert or remove the signal
cable or the power cord to avoid damaging the projector.
Turn on High Fan Speed Mode when located in high altitude areas.
Rev B September2020
page 14
Important Information

Installation Precautions DigitalProjection E-Vision Laser5100 Series
The projector generates heat during use. The internal fans dissipate the heat of the
projector when shutting down, which could continue for a certain period. After the
projector enters STANDBY MODE, remove the power cord. DO NOT remove the
power cord during shutdown as it may cause damage to the projector and may
affect the service life of the projector.
Do not place heavy objects on top of the projector chassis.
Important Information Rev B September2020
page 15

DigitalProjection E-Vision Laser5100 Series ProductLabels
Product Labels
Projector
E-Vision Laser 5100 WUXGA
Manufacturers ID Label
Explanatory Label
Laser Aperture Label
E-Vision User Guides
Follow link for Projector Documentation
この二次元バーコードをスキャンしてプロジェクターのデータを取得してください
请扫描条码来取得投影机的文件
프로젝터 설명서를 보려면 링크를 팔로우하십시오
Suivre le lien pour accéder à la documentation du projecteur
Produktdokumentation nden Sie unter dem Link
User Guides Label
Rev B September2020
page 16
Important Information

ProductLabels DigitalProjection E-Vision Laser5100 Series
Remote Control
激 光 辐 射 勿直视激光 束
2类 激 光 产 品
波 长 ：6 4 0 - 6 6 0 n m
最 大 输 出 ：1 m W
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH: 640-660nm
MAX OUTPUT: <1mW
CLASS II LASER PRODUCT
ÉVITEZ L'EXPOSITION - UN RAYONNEMENT LASER
EST ÉMIS PAR CETTE OUVERTURE RAYONNEMENT LASER
NE REGARDEZ PAS DIRECTEMENT LE RAYONNEMENT
ADVANCETECH CO., LTD (FACTORY)
11/F-1, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei
City 23584, Taiwan, R.O.C.
WAVELENGTH:640-660nm
MAX OUTPUT:<1mw
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50 dated June
24.2007. IEC/EN60825-1:2007
P/N: SN1411010 Product code:1512010
IEC/EN 60825-1:2007 IEC/EN 60825-1:2014
波 長 ：6 4 0 - 6 6 0 n m
最 大 輸 出 ：1m W
雷 射 輻 射 勿注視波束
等級2雷射產品
Remote Control Label
Important Information Rev B September2020
page 17

DigitalProjection E-Vision Laser5100 Series ProductLabels
Label Locations
1
2
1. Location of Hazard Warning Symbol
and Laser Aperture Label on the body
of the projector.
2. Location of Manufacturer’s ID Label
and Explanatory Label with
Certification Statement and Risk
Statement on the body of the projector.
Rev B September2020
page 18
Important Information

ProductLabels DigitalProjection E-Vision Laser5100 Series
3
3. Location of Remote Control Label on
the back of the remote.
Important Information Rev B September2020
page 19

DigitalProjection E-Vision Laser5100 Series Operation and Configuration Precautions
Operation and Configuration Precautions
Do not make changes to the networking configuration unless you understand what you
are doing, or have taken advice from your Network Manager. If you make a mistake, it is
possible that you will lose contact with the projector. Always double-check your settings
before pressing the APPLY button. Always keep a written note of the original settings,
and any changes you have made.
Software updates should NOT be carried out except by, or with the supervision of,
Digital Projection Service personnel.
Rev B September2020
page 20
Important Information