Digital Watchdog STAR-LIGHT DWC-B6263WTIR650 User manual

Quick Start Guide Quick Start Guide
WHAT’S IN THE BOX
Star wrench 1Mounting
template 1
DC plug
cable 1
Screws and
plastic anchors
- 4pcs
1 set
Test video
cable 1
Moisture
absorber and
absorber guide
(recommended)
1
Sunshield
cover and
adjusting
screws
1 set Quick setup
guide 1
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Power Requirements Power Consumption
DC12V/AC24V dual voltage
DC12V (LED o): 3.0W
DC12V (LED on): 6.0W
AC24V (LED o): 2.7W
AC24V (LED on): 5.5W
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
DWC-B6263WTIR650
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Attention: This document is intended to serve as a quick reference for initial
setup. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
DW® Universal HD over Coax® long-range
bullet cameras
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or fire.
3. Install the moisture packet in the base of the camera’s lens.
a. Remove the moisture absorber from the packaging.
b. Cut the card and folder along the dotted line.
c. Place the moisture absorber behind the camera’s lens module. See drawing for more information.
4. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
WARNING: It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
NOTE: The camera will generate enough heat to dry moisture
during operation. In most cases it will not need the
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.

Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
a. Remove the camera’s dome to access the joystick and OSD
control on the base of the camera.
b. Use the OSD Switch to switch the camera’s signal.
• To switch the camera to HD-TVI mode, press OSD joystick to the
left for 5 seconds.
• To switch the camera to HD-Analog mode, press OSD joystick to
the right for 5 seconds.
• To switch the camera to CVBS mode, press OSD joystick
up for 5 seconds.
• To switch the camera to HD- CVI mode, press OSD joystick
down for 5 seconds.
1. Once all cables have been connected, use the screws included with
the camera to properly mount and secure the camera to the mounting
surface.
2. To adjust the camera’s tilt, loosen the screws at the base of the
camera’s bracket. The camera’s max angles are:
Pan: 0°~ 360°
Tilt: 0°~ 90°
3. To adjust the camera’s focus and zoom:
a. Remove the sun-shield and front case from the camera.
b. Unlock the zoom or focus screws by rotating them
counterclockwise.
c. Adjust the zoom and focus screws at the base of the
camera module to achieve a clear image.
d. Tighten the screws and close the front case
by rotating it clockwise.
STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN
THE CAMERA
Front Case
Focus Lever
Far ↔Near
Zoom Lever
Wide
↔
Tele
Rev Date: 04/21
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Front case
Zoom lever
Wide Tele
Focus lever
Far Near
R
L
UD
1
2
3
U
Enter R
L
D
HD-AHD-TVI
CVBS(960H)
HD-CVI
Test video connector for
on-site configuration