Digitus DA-70202 User manual

User Manual
USB2.0 to IDE and SATA Adapter Cable
Model: DA-70202

I. Foreword
Congratulations on your purchase of our product! We will
show you a new storage concept with safety and convenience.
It is our pleasure to give you the best solution to expand your
HDD'S Capacity and enhance your data's reliability in PC
system or Mac system. Before using the product, please read
this manual carefully for further recognizing of the product.
II. System Requirement
Basic environment for setup this device:
Hardware requirement: a PC, Notebook or Mac system
with free USB interface
Operation system: Windows7/8/10/Vista/XP/2000,
Mac OS 9.x above
III. Feature
1. Supports IDE/SATA 2.5/3.5/5.25 devices
2. Support USB2.0 to Serial ATA interface, transfer rate
up to 480Mb/sec
2. Support USB2.0 to IDE interface, transfer rate up to
480Mb/sec
3. Bus power for 2.5 Hard Disk
IV. Package Content
• USB to IDE/SATA Adapter cable
• Supported CD Driver
• User's Manual

4pin Power
C
USB2.0 Power Plug(red)
Power/Activity-LED
(blue & red)
USB2.0 Plug
SA
T
A
Plug fo
r
SATA device
44-pin IDE plug fo
r
1.8/2.5 IDE HDD
40-pin IDE plug fo
r
3.5/5.25 IDE device
Note: For 3.5/5.25 IDE devices, please plug in a 5V/12V power
supply (not included) to appropriate port on the back side of
HDD or DVD, so that the PC power switch (on/off) can’t control
the current to HDD or DVD. If you want to cut off the current to
HDD or DVD, then you need to plug out the power plug from
3.5” IDE HDD or 5.25 DVD devices.
Both IDE and SATA plug are protected against polarity
reversal and should be easily connected to the device. If not,
Pease check if you use the plug in the right way. Please be
sure, that your IDE device is configured as MASTER.

SATA Plug LED
LED
V. Hardware installation
a. Connect to a 2.5 SATA HDD
b. Connect to a 2.5 IDE HDD
For a 2.5 SATA HDD or IDE HDD, plug directly the SATA
connector or the 44pin connector into the appropriate ports
on the rear of the HDD, and plug the USB signal/data plug
(Black) into USB port of PC.
Note: If you HDD need more than 500mA, please plug
the USB extra power plug (Red) additionally into other
USB port.
44pin IDE Plug

3.5 SA
T
A
HDD
5V/12V Power suppl
y
(Please see chapter VIII. How to use power supply from
your desktop computer). Alternatively, you can use
5V/12V external power supply
3.5 IDE HDD 5V/12V Power supply
LED
c. Connect to a 3.5 SATA HDD
d. Connect to a 3.5 IDE HDD
For a 3.5 SATA HDD or a 3.5 IDE HDD, plug directly the
SATA connector or the 40pin connector into the appropriate
ports on the rear of the HDD, and plug the USB
signal/data plug(Black) into USB port of PC, then plug the
4-pin plug of the power supply (not included) to the 4-pin
power jack (for IDE HDD direct plug in HDD power
connector), and the other end plug to power source.

e. Connect to a 5.25 IDE HDD
For a 5.25 CD/DVD device, plug directly the 40pin
connector into the appropriate ports on the rear of the
CD/DVD device, and plug the USB signal/data plug (Black)
into USB port of PC, then plug the 4-pin plug of the power
supply to the 4-pin power jack (for IDE CD/DVD direct plug
in CD/DVD power connector), and the other end plug to
power source.
VI. Driver installation
a. Setup mode under Windows7/8/10/Vista/XP/2000
system
Under Windows7/8/10/Vista/XP/2000, the system will find
and setup [USB Mass Storage Device] directly
b. Setup mode under Mac OS system
If your system is Mac OS9.0 or above, the system can find
the driver directly. If your system is OS8.6, you have to
download and setup [USB MASS STORAGE SUPPORT
1.3.5] from SOFTWARE SUPPORT
Website : http://www.apple.com/support
5V/12V
Power supply

VII. Under the following situation, you need to use
5V/12V Power supply
1)When connects with the 3.5 / 5.25 SATA devices
( HDD, CD ROM , DVD Rom )
2)When this product connect with 3.5 / 5.25 IDE devices
( HDD , CD Rom , DVD Rom )
3) Connecting with the 2.5 SATA HD, when the power
consumption is bigger than 1A
4) Connecting with the 1.8 / 2.5 IDE HDD, when
power consumption is bigger than 1A
* Remove the multi-function adapter
Warning: Before removing the multi-function, you must
finish the following procedure:
1) Click the icon in the [Desktop] window of your computer
2) A [Safely Remove Hardware] message window will
appear, click the [Stop] button
3) [It is now safe to remove the USB device] message will
appear, close the [Safely Remove Hardware] window
4) Turn the power switch to [OFF] position
5) Remove the 5V/12V power supply if it is applied
Note:
New Hard Disk Drive must be formatted before
in use

VIII. How to use the device with power supply
from computer
1. Plug DA-70202 into USB port
2. Plug 3,5HDD into the correspondent port ( SATA/IDE)
3. Plug the power for supplying mentioned devices in Point
VII. from computer

Also, for 5,25 devices
Connect from the 4 pin power connector of the
power supply to DA-70202 (4Pin DC)
Power supply

Disclaimer
Hereby ASSMANN Electronic GmbH, declares that this device is in
compliance with the requirements of Directive 2014/30/EU and the
Directive 2011/65/EU for RoHS compliance. The complete
declaration of conformity can be requested by post under the below
mentioned manufacturer address.
Warning:
This device is a class B product. This equipment may cause some
radio interference in living environment. In this case, the user can be
requested to undertake appropriate measures to prevent
interference.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
All the information in this document is
subject to change without prior notice. The
manufacturer makes no representations or
any warranties regarding the Contents of this
manual. The information contained in this manual
is provided for the general use by the customers.
No part of this document may be reproduced or
transmitted in any form by any means without the
express written permission of The
manufacturer. All brand names and product
names used in this document are trademarks or
registered
trademarks of their respective holders.