Dimension One Spas D1 SpaIQ User manual

D1® SpaIQ™
DISTINCTLY D1®


Table of Contents
D1® SpaIQ™ ��������������������������������������������������������������������������������������������������������������������������������������5
Easily integrate your spa to the Internet of Things! �����������������������������������������������������������������������������5
D1® SpaIQ™ overview �����������������������������������������������������������������������������������������������������������������������5
D1® SpaIQ™ Installation and Connections (For Aftermarket Kit) ������������������������������������������������6
D1® SpaIQ™ Spa Transmitter (CO Module) installation ��������������������������������������������������������������������6
Connection of the D1® SpaIQ™ Spa Transmitter (CO Module) ���������������������������������������������������������6
Home Transmitter (EN Module) installation�����������������������������������������������������������������������������������������7
Connection of the Home Transmitter (EN Module)������������������������������������������������������������������������������7
Pairing the Spa Transmitter (CO Module) and the Home Transmitter (EN Module)����������������������������8
LED Status �����������������������������������������������������������������������������������������������������������������������������������������9
LED������������������������������������������������������������������������������������������������������������������������������������������������������9
Application���������������������������������������������������������������������������������������������������������������������������������������10
Download application ������������������������������������������������������������������������������������������������������������������������10
Using the app ������������������������������������������������������������������������������������������������������������������������������������10
On your home network ����������������������������������������������������������������������������������������������������������������������10
On the Internet�����������������������������������������������������������������������������������������������������������������������������������10
Setup your Wi-Fi on your device����������������������������������������������������������������������������������������������������11
Start the D1® SpaIQ™ application����������������������������������������������������������������������������������������������������11
Features��������������������������������������������������������������������������������������������������������������������������������������������12
Login page�����������������������������������������������������������������������������������������������������������������������������������������12
New account creation������������������������������������������������������������������������������������������������������������������������12
Choose a spa ������������������������������������������������������������������������������������������������������������������������������������12
Home page����������������������������������������������������������������������������������������������������������������������������������������13
Spa state �������������������������������������������������������������������������������������������������������������������������������������������13
Change temperature��������������������������������������������������������������������������������������������������������������������������14
Turn on/off accessories ���������������������������������������������������������������������������������������������������������������������14
Turn on/off the lights��������������������������������������������������������������������������������������������������������������������������15
Control your LiquidFX™ ��������������������������������������������������������������������������������������������������������������������15
Water Care ����������������������������������������������������������������������������������������������������������������������������������������16
Reminders �����������������������������������������������������������������������������������������������������������������������������������������16
Modifying schedules��������������������������������������������������������������������������������������������������������������������������17
Spa Settings ��������������������������������������������������������������������������������������������������������������������������������������18
SpaIQ™ network �������������������������������������������������������������������������������������������������������������������������������18
Change channel ��������������������������������������������������������������������������������������������������������������������������������19
Temperature units������������������������������������������������������������������������������������������������������������������������������19
Name�������������������������������������������������������������������������������������������������������������������������������������������������20
Technical Info�������������������������������������������������������������������������������������������������������������������������������������20
Settings����������������������������������������������������������������������������������������������������������������������������������������������21
Add a spa ������������������������������������������������������������������������������������������������������������������������������������������21
Account����������������������������������������������������������������������������������������������������������������������������������������������22
Tutorial�����������������������������������������������������������������������������������������������������������������������������������������������22
Dealer page���������������������������������������������������������������������������������������������������������������������������������������23
Troubleshooting ������������������������������������������������������������������������������������������������������������������������������23
Home Transmitter (EN Module) LED status ��������������������������������������������������������������������������������������23
Spa Transmitter (CO Module) LED status�����������������������������������������������������������������������������������������24
Specications ����������������������������������������������������������������������������������������������������������������������������������25
Environmental������������������������������������������������������������������������������������������������������������������������������������25
Compatibility��������������������������������������������������������������������������������������������������������������������������������������25
Regulatory Compliance Information for Internal Transceiver Module������������������������������������������������25
North American compliance���������������������������������������������������������������������������������������������������������������26
European and international compliance ��������������������������������������������������������������������������������������������26

WARNING: Before installing or connecting the unit, please read the following:
•For optimum performance please carefully read the manual before installation�
• Install the D1® SpaIQ™-CO module at least 12" (30 cm) away from any metal part or any metal
foil�
• The D1® SpaIQ™-CO module should be installed such as it can be relocated under the spa in
order to obtain optimal reception after nal installation of the spa in the yard.
• To satisfy FCC RF exposure requirements for mobile and base station transmission devices,
a separation distance of 8" (20 cm) or more should be maintained between the D1® SpaIQ™
modules and persons during operation; to ensure compliance, operation at closer than this dis-
tance is not recommended�
• The antennas used for these modules must not be co-located or operating in conjunction with
any other antenna or transmitter�
• To power the D1® SpaIQ™-EN, only use the power supply unit provided with the D1® SpaI-
Q™-EN�
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been giv-
en supervision or instruction concerning use of the appliance by a person responsible for their
safety�
• Children should be supervised to ensure that they do not play with the appliance�
DISPOSAL OF THE PRODUCT
The appliance (or the product) must be disposed of separately in accordance with the local
waste disposal legislation in force�
COMPATIBILITY REQUIREMENTS
D1® SpaIQ™ modules for FCC (North America) models (915 MHz):
Home and spa transmitter kit: 6600-309
D1® SpaIQ™ modules for ETSI (Europe) models (868 MHz):
Home and spa transmitter kit: 6600-310
Compatible System:
• SpaIQ™ is compatible with any Dimension One spa equipped with D1 Hub™ and D1
Smar-tHUB™ control systems manufactured in or after 2015�
D1® SpaIQ™ application:
Compatible with devices running:
• iOS 8�0 or higher
• Android 2�3 or higher
ROUTER AND INSTALLATION REQUIREMENTS
Any standard router with an available 100 Mbps (wired LAN) RJ45 port can be used� The router
must also have its Port 10022 open, which is normally a default setting� A 3-foot (0�9 m) Ethernet
cable is included�
The home transmitter will need a main supply (120V in North America, 220V in Europe) nearby to
allow connection of the transformer�
Aeware®, Gecko®, and their respective logos are Registered Trademarks of Gecko Alliance Group�
D1® SpaIQ™, in�xm2™, in�xe™, in�yt™, in�ye™, in�therm™ and their respective logos are Trade-
marks of Gecko Alliance Group�
All other product or company names that may be mentioned in this publication are trade-names,
trademarks or Registered Trademarks of their respective owners�

1
D1® SpaIQ™
Easily integrate your spa to the Internet of Things!
Simplest of setups
D1® SpaIQ™ eliminates all the
complexities of connecting your spa
to the Internet and transforms your
smartphone or tablet into your ulti-
mate Wi-Fi spa remote control� D1®
SpaIQ™ comes with a state-of-the-art
app and 2 prepaired radio frequency
transmitters, one being part of your
spa system and the second one being
connected to your Internet router� Both
RF transmitters are prelinked to one
another, enabling an immediate and perfect communication between you and your spa�
Strong and long range communication signal
Through their proprietary RF technology, D1® SpaIQ™ transceivers emit a strong, stable and long
range signal between your spa and your router (about 3 times longer than regular Wi-Fi signal)� No
need for repeaters or boosters: your spa will always remain within reach in typical backyard set-
tings�
State-of-the-art app with push notications
D1® SpaIQ™ streamlined application makes it very easy to control and program all the functions
and features of your spa from your smartphone or your tablet� Even when you’re away from home,
you get full control of your water care settings, ltration cycles, water temperature, economy modes
and a lot more. Push notications will always keep you informed on the status of your spa, even
when your app is not open�
D1® SpaIQ™ overview
Home Transmitter (EN Module) Spa Transmitter (CO Module)
Fastening bracket
Pairing
activation
Status LED Status LED
CO pack connection
Micro USB power RJ45 Ethernet connection

2
D1® SpaIQ™ Installation and Connections (For Aftermarket Kit)
D1® SpaIQ™ Spa Transmitter (CO Module) installation
Before proceeding with any installation, be sure to turn spa power off�
The D1® SpaIQ™ Spa Transmitter unit must be installed under the spa skirt, at
least 12" (30 cm) away from any metal component or structure� This is necessary
to ensure optimal transmission� In some cases, it may be necessary to relocate
the unit once the spa is installed in the yard to ensure proper signal transmission
and distance�
Install the Spa Transmitter so the module can be repositioned to optimize the signal strength in the
yard (it is possible to see the signal strength with the D1® SpaIQ™ application in the menu Setting
-> Network -> Signal strength)� We recommend that you install the unit with a #8 pan head screw�
Here are some suggestions for a successful installation:
• Install the unit as high as possible within the spa skirt, but keep it away from the spa frame if it is
metallic�
• Route the cable and leave some slack in the Spa Transmitter cable so the Spa Transmitter can
be moved around in case of reception problems�
• Install the Spa Transmitter in a corner of the spa to help avoid metallic components, accessories
and piping close to the Spa Transmitter�
• The Spa Transmitter should be installed as close as possible to the house to optimize signal
strength� It is recommended to install the D1® SpaIQ™ module on the side of the spa facing
the house to increase the signal� A body of water between the Spa Transmitter module and the
Home Transmitter will reduce the signal strength�
Connection of the D1® SpaIQ™ Spa Transmitter (CO Module)
Simply connect the Spa Transmitter module
into an available CO port of the spa pack
(or any other accessory with a free CO port,
such as the audio amplier, or the spa sani-
tizing system)�
Note: That the Spa Transmitter only has a
single CO cable and thus must be installed
at the end of the CO chain if more than a
single accessory is installed on the same
CO port of the spa pack�
Note: Before powering up the spa pack
again, please go to the next step and install
the Home Module (EN Module)�
OFF
OFF
Note: The Spa Transmitter (CO Module) installation process is used when you need to replace
the module of the D1® SpaIQ™ kit or used for aftermarket kit� Otherwise, the Spa Transmitter
(CO Module) arrives pre-installed from the factory�
LD
CO port
CO port

3
Home Transmitter (EN Module) installation
The Home Transmitter unit must be installed inside
the house near the router as it needs to be connected
to it� The Home Transmitter is provided with an Ether-
net cable and a power supply� If required, a longer
cable of good quality can be used by the installer
(longer cable not provided) to install the Home Trans-
mitter closer to the spa within the home� The only
requirement for installation location is that household
current be available to power the Home Transmitter using the provided wall transformer�
The Home Transmitter can be xed in the house to optimize the signal strength. We recommend
that you install the unit with a #8 pan head screw�
Here are some suggestions for a successful installation:
• If possible, install device on the rst oor of your house.
• If installing in a basement, place at highest level possible and closest to a window�
• Try to install as far as possible from materials that may interfere with signal (ie� metal structures,
thick cement walls)�
• Install as far as possible from router as the signal emitted by the antenna may interfere with RF
signal�
Connection of the Home Transmitter (EN Module)
Simply connect Ethernet cable into the RJ45 port of the Home Transmitter and in one of the avail-
able LAN ports on the router�
Finally, to power up the Home Transmitter, connect the provided transformer to a 120V (North
American model) or 220V (European model) household supply and connect the USB cable between
the transformer and the Home Transmitter�
Micro USB power
RJ45 Ethernet connection
LAN port, routerEthernet cable

4
Pairing the Spa Transmitter (CO Module) and the Home Transmitter (EN Module)
The pairing process is used when you need to replace one module of the D1® SpaIQ™ kit� Other-
wise, the D1® SpaIQ™ arrives pre-paired from the factory�
1� Power up the Home Transmitter
2� Press on the pairing button with a paper clip or some similar tool� When the pairing mode is ac-
tive the status LED ashes YELLOW in a rapid pattern. The Home Transmitter is then in pairing
mode and will remain in this mode until it pairs with an Spa Transmitter, or until it is reset (power
cycled)�
3� Shut off the spa’s breaker (thus turning off the Spa Transmitter), wait a few seconds, and then
ip the breaker back on. Within a few seconds, the pairing operation should complete and the
Home Transmitter status LED will no longer be YELLOW.
Note: D1® SpaIQ™ modules can be paired as often as necessary, but can only be paired with a
single counterpart module at a time� Once paired, the modules store this information permanently
until the next pairing operation� Pairing information is stored in non-volatile memory, so pairing is not
required after a power failure� Only a Home Transmitter can initiate a pairing, so it is important that
the pairing begin with putting the Home transmitter module in pairing mode�
If several spas are powered up at the same time with a Home Transmitter in pairing mode (for
instance, in a dealer showroom), only the 1st spa to successfully connect to the Home Module will
pair� As this can be random, it is recommended that only 1 spa be powered up at a time during the
pairing process�
pairing button
Main electrical box GFCI panel
status LED

5
LED Status
LED
Each D1® SpaIQ™ module has a status LED that can be used for troubleshooting purposes� The
LED is located on the top of both enclosures�
Home Transmitter Spa Transmitter
Pairing mode Yellow (Blinking) Pairing mode Yellow (Blinking)
Router not detected Red Spa controller not detected Red
Router detected Green
D1® SpaIQ™ server
detected Module is fully
functional Blue
D1® SpaIQ™ server
detected Module is fully
functional Blue
• When the LED status is blinking (blue, green or red) this indicates that the communication be-
tween the EN module and the CO module it not established�
status LED status LED

6
Application
Download application
The D1® SpaIQ™ app allows you to control your spa using your home network or an Internet
connection anywhere in the world� The D1® SpaIQ™ app is waiting for you in the App Store for iOS
devices and on Google Play for Android — search for «D1® SpaIQ™» then click on it to install�
Using the app
On your home network
It is possible to access your spa with the D1® SpaIQ™ app through your home network� To be able
to see your D1® SpaIQ™ in the application you need to connect your device to the same router
(Wi-Fi network) than the one used to connect your Home Transmitter�
Go to the Wi-Fi settings section of your mobile device and choose the same network that your spa
is connected to (i.e. Home). Once you’ve selected it, wait until your device conrms the connection.
On the Internet
The D1® SpaIQ™ allows you to use the Internet to control your spa from anywhere in the world� In
order for them to communicate, both the D1® SpaIQ™ module and your device must be connected
to a network that allows access to the Internet�
Once your Home Transmitter is connected to the Internet (the LED status is blue), you can use your
D1® SpaIQ™ app any time your device is also connected to the Internet (wireless or cellular net-
work), even if you are away from home� To have access to your spa away from home, you will need
to have previously linked your mobile device to your spa on your home network�

7
Setup your Wi-Fi on your device
Before using your application, go to the Wi-Fi section of your device’s
settings� Make sure you are connected to your home network� This needs
to be the same Wi-Fi provided by the router to which you connected your
Home Transmitter�
Start the D1® SpaIQ™ application
Find the icon for the D1® SpaIQ™ application, then tap on it to open it�
The rst time you use the application a message will ask you: “D1®
SpaIQ™” Would like to send you notications. If you choose Allow, the
application will send you notications about the status of your spa. If you
choose Don’t Allow, the application will not send you notications.
If you change your mind later concerning notications, you may add or
remove notications for the D1® SpaIQ™ application.
On iOS, go in your settings menu and choose D1® SpaIQ™� Select the
notications menu, you can turn notications on or off from this page.
On Android, go to your settings menu and then into the notications menu.
Select the D1® SpaIQ™ app, from this page you may turn notications on
or off�
Home Wi-Fi
“D1 SpaIQ” Would like to
send you notifications
Notifications may include alerts,
sounds, and icon badges. These
can be configured in Settings.
Don’t Allow Allow
D1 SpaIQ

8
Features
Login page
Before using your application, you must create an account rst and then,
you’ll be able to sign in. Your account will give you the opportunity to have
access to your spa from any D1® SpaIQ™ application�
New account creation
When you choose to create a new account, you agree at the same time our
Terms of Service and our Privacy Policy. You can read them at any time
through this link: https://geckointouch�com/legal�
Choose a spa
This page displays all the spas detected by your application� To detect
your spa, you need to connect your mobile device to the same net-
work to which you connected your Home Transmitter�
Once you have done a connection with the spa its name will be saved
on this page to allow you to connect to this spa from anywhere�
To add a spa later on, go to page 17 of this techbook for instruc-
tions� The RF signal strength (communication between the two D1®
SpaIQ™ transmitters) is illustrated on the Select a spa page� There
are 5 possible states:
● Signal superior to 80%
● Signal between 80% and 51%
● Signal between 50% and 31%
● Signal below 30%
● The Spa Transmitter is not available
SIGN IN
CREATE AN ACCOUNT
By signing up, you agree to the Terms of
Service and Privacy Policy
name
email
password
confirm password
New Account
Cancel Create
12:15 PM
By signing up, you agree to the Terms of
Service and Privacy Policy
name
email
password
confirm password
New Account
Cancel Create
12:15 PM

9
Home page
The main screen gives you access to your accessories, water temperature, water care and settings�
Spa state
This page displays all the active states of your spa� Below is a quick description of each state you
may encounter on your spa� Each state is associated to a priority and color that determines the
color of the widget on the home page�
(Yellow) Indicates that there is an error on your spa.
(Dark blue) Indicates that there is presently an active user
demand on your spa (ie� pump or light is on)�
(Red) Indicates that your spa is now heating to your
set point�
(Blue) Indicates that your spa is now in a ltering
cycle�
(Green) Indicates that your spa is now in economy
mode�
(Gray) Indicates that your spa is running normally
(there is no user demand, heating, no ltration
or economy active)�
The widget on the home page displays a single color at a time� The color displayed is decided by
priority of state� The established priority is as listed above�
My Spa
Cancel Create
12:15 PM
100 °F
Heating to 100°F
Filtering is active
Account setting
Settings menu
Reminders menu
Spa name
Message center that indicates status
of your spa: heating, filtration, error
if you click on the message center
you will access the Spa state page
Ac
cessories control line
Indicates current spawater
temperature. Color varies according
to most important active state.
Touch to change set point
Water Care menu
My Spa
Cancel Create
12:15 PM
Heating to 100°F
Filtering is active
Spa state

10
Change temperature
Touch the centered widget to reveal the temperature control bar�
Use the slider on the control bar to change your spa’s temperature*
set point�
*If you are in economy mode your spa temperature will be 20°F below
your set point�
Turn on/off accessories
According to your spa pack conguration, you can start or stop an ac-
cessory by simply touching the associated icon� The icon will become
animated when the accessory is on� Simply press on the icon to start
or stop the accessory� If your accessory has more than one speed,
press the button until the desired speed is reached�
The icon designs are customized according to your spa pack congu-
ration:
Pump
Fountain
Light
My Spa
Cancel Create
12:15 PM
93 °F
Spa is in use
Heating to 100°F
My Spa
Cancel Create
12:15 PM
100 °F
Heating to 100°F
Filtering is active
Ac
cessories

11
Turn on/off the lights
To control your spa lights, simply press the button to turn it on
or off�
Control your LiquidFX™
This menu is only available if an LiquidFX is detected in your
spa accessories�
To turn on or off the LiquidFX, you can use, if you want, the
light icon on your home page� To go to your LiquidFX page,
simply swap to the left�
The LiquidFX™ page allows you
to customize your color zones in or
around your spa�
The light bulb icons allow you to turn
on and off your LiquidFX�
To select a zone, click on the wanted
one in the “zone selection” stripe. To
change the color, use the color wheel
to choose the one you want� On the
left side, the intensity slider allows you
to modify the brightness of your lights�
Use the rainbow icon to get color
gradation�
The synchronize/desynchronize icon
gives you the possibility to match the
color of the selected zone with the
other zones
My Spa
Cancel Create
12:15 PM
100 °F
Heating to 100°F
Filtering is active
Light
My Spa
Cancel Create
12:15 PM
Spa is in use
Heating to 100°F
Off
On
Intensity
Zone selection
Color wheel
Rainbow icon
Synchronize/
desynchronize icon
My Spa
Cancel Create
12:15 PM
90 °F
Spa is in use
Heating to 100°F
Swap to
LiquidFX
Turn on/off
LiquidFX

12
Water Care
The Water Care page will help you set up your ideal ltration and
heating settings� Choose between Away from Home, Beginner,
Energy Savings, Super Energy and Weekender, depending on your
need� Touch the Water Care name you would like to activate, a green
checkmark will appear on the icon, indicating you have selected it�
By default, each Water Care mode has pre-congured schedules of
economy and ltration. To modify Water Care options, touch the pen-
cil icon at the right end of the desired Water Care to open its menu�
Below you have a short description of each Water Care at default
state:
Away From Home:
In this mode the spa will always be in economy; the set point
will be reduced by 20° F�
Beginner/Standard:
The spa will never be in economy mode and will be ltering
according to the pack’s low level conguration.
Energy Savings:
The spa will be in economy mode during the peak hours of the
day and resume normal mode on the weekend�
Super Energy Savings:
The spa will always be in economy mode during peak hours,
every day of the week�
Weekender:
The spa will be in economy mode from Monday to Friday, and
will run normally on the weekend�
Reminders
Reminders page will help you to make a follow-up of your mainte-
nance� The D1® SpaIQ™ will remind you to perform required mainte-
nance tasks on your spa, such as rinse lter or clean lter. Each task
has its own reminder duration based on normal use� The owner can
reset his reminders after the spa maintenance�
My Spa
Cancel Create
12:15 PM
Water Care
Away from home
Standard
Energy Saving
Super Energy Saving
Weekender
My Spa
Cancel Create
12:15 PM
Reminders
Have a spa check up
Required in 729 days
Rinse filter with hose
Required in 29 days
Clean filter in solution
Required in 59 days
Change water
Required in 89 days
Reset reminders

13
Modifying schedules
In this menu it is possible to add, remove or edit schedules of economy or ltration.
To have access to this menu, simply touch the tabs:
• Water Care menu - the little pen at the right of the wanted water care, page 12�
• Touch the Economy tab to modify the economy schedules and Filter cycle tab for the ltration
schedules. You can add economy or ltration schedules by touching the « + » symbol.
• To delete a schedule, touch the garbage can icon at the right end of the desired line�
You can modify the programmed schedules by selecting one and adjusting the schedule.
You have several possibilities for the schedule (Mon-Fri, weekend, every day, or single days). The
schedules will be repeated weekly� The time and duration are set in 30 minute increments� Once
you have set the schedule, use the arrow at the top of the page to go back� Ensure that you have
selected the desired Water Care mode in the main Water Care menu�
When an economy schedule is active, the set point will be reduced by 20°F, which means that the
heating system will not be engaged unless the temperature falls to 20°F below the spa’s set tem-
perature�
The ltration schedule is applied to the main ltration pump, most likely pump 1. If your spa uses a
circulation pump congured to run 24 hours, the screen will show purge schedules instead of ltra-
tion. The purges are pre-programmed for a xed number of minutes, therefore the duration will be
set to N/A on the screen and only the start time can be modied.
My Spa
Cancel Create
12:15 PM
Standard
00:00 00:00Every day
Start Stop +
Economy
Economy (1) Filter cycle (1)
My Spa
Cancel Create
12:15 PM
Standard
00:00 24.0hEvery day
Start Duration +
Filter cycle
Economy (1)
Filter cycle (1)
My Spa
Cancel Create
12:15 PM
Every day
Weekend
Mon-Fri
Saturday
00:00
00:30
01:00
01:30
00:00
00:30
01:00
01:30
Start StopDay
Apply changes

14
Spa Settings
My Spa
Cancel Create
12:15 PM
Spa Settings
Technical info
Temperature unit
SpaIQ network
Spa name
Celsius (°C)
My spa
C F
In the Settings page you can access the following:
• Temperature units
• SpaIQ™ network
• Spa name
• Technical info
To select an item, tap on the arrow next to it� It will open the selected
menu�
SpaIQ™ network
The SpaIQ network menu allows you to have
access to information concerning the RF con-
nection parameters between the Home Trans-
mitter and the Spa Transmitter� This menu
gives you access to:
• Channel
• Signal strength
• Reset channel (resets channel to ���
default)
To change channels, press on the Channel
line�
My Spa
Cancel Create
12:15 PM
Spa Settings
Technical info
Temperature unit
SpaIQ network
Spa name
Celsius (°C)
My spa
C F
My Spa
Cancel Create
12:15 PM
SpaIQ network
Channel
Singal strength
Reset channel
20
100%

15
Change channel
My Spa
Cancel Create
12:15 PM
Change channel
20
21
22
23
19
18
17
Apply changes
The Change channel page allows you to change the channel used by
the two D1® SpaIQ™ modules�
In some cases, this can help you to have a stronger signal�
You can have access to this page by touching the following tabs:
Spa settings (at the bottom right, page 9), SpaIQ network (page
14) - Channel (page 14)�
Temperature units
My Spa
Cancel Create
12:15 PM
Spa Settings
Technical info
Temperature unit
SpaIQ network
Spa name
Celsius (°C)
My spa
C F
Heating management Smart
My Spa
Cancel Create
12:15 PM
Spa Settings
Technical info
Temperature unit
SpaIQ network
Spa name
Celsius (°C)
My spa
C F
Heating management Smart
Celsius (°C)
Fahrenheit (°F)
Cancel
This menu lets you change the units used to
display temperature�
You can have access to this page by touching
the following tabs:
Spa settings (at the bottom right, page 9)
then temperature units�

16
Name
This section allows you to edit the name of the spa�
You can have access to this page by touching the following tabs:
Spa settings (at the bottom right, page 9), then change Spa name�
Technical Info
This section shows information about the D1® SpaIQ™ software
number and the revision numbers of the different components of your
system�
You can have access to this page by touching the following tabs: Spa
settings (at the bottom right, page 9) - Technical info�
My Spa
Cancel Create
12:15 PM
Name
My Spa
QWE R T Y U I O P
LKJHGFDSA
Z X C V B N M
X
123
Space
Done
“Spa” Space Scam
My Spa
Cancel Create
12:15 PM
Technical Info
MAC address
Connection type
inYT
Low-level Conf.
d8:80:39:a2:0c:f4
Local
SpaIQ EN
SpaIQ CO
88v6.0
89v5.0
225v9.0
1
Spa
SpaIQ
Table of contents
Popular Control Unit manuals by other brands

dymax
dymax 826 user guide

Texas Instruments
Texas Instruments bq26220EVM-001 user guide

Cisco
Cisco GS7000 Installation and configuration guide

Sony
Sony IFU-WLM3 operating instructions

Telit Wireless Solutions
Telit Wireless Solutions SL869-V3 EVK Product user guide

Renishaw
Renishaw SLM 250 Installation and operation