Directed Electronics 1100X/F-GD Installation manual

PROGRAMMING INSTRUCTIONS

ATTENTION! BEFORE PROCEEDING WITH INSTALLATION,

LOOK FOR INSTALL GUIDE UPDATES AT WWW.DIRECTED.COM.

PRODUCT DESCRIPTION

The 1100X/F-GD interface module is used when installing remote start

products in GM/Daewoo vehicles equipped with a factory immobilizer.

The 1100X/F-GD allows for easy interfacing between the remote start and

the factory immobilizer, while maintaining the integrity of the OEM sys-

tem. The factory transponder-based anti-theft system uses a small elec-

tronic chip hidden in the key to send a code to the vehicle’s transceiver

when the ignition is energized. The key must be placed in the ignition

and turned to the RUN position. This energizes a coil surrounding the

key, which in turn energizes the chip, which sends a code to the vehicle. If

the vehicle does not detect the code being sent, the vehicle will start and

then immediately shut off or will just crank, and the anti-theft light will

ﬂash.The 1100X/F-GD provides a valid code to the vehicle whenever it is

remote started, but does not affect the immobilizer system during normal

vehicle operation; the immobilizer system remains fully functional.

STEP 1: SELECT INSTALLATION MODE

Completethewireconnectionstothevehicleandtotheremotestarter/alarm

system. Connect all harnesses including the 4-pin power harness. The

module LED will now ﬂash green intermittently. (Note: if this condition is

not present, your module may need to be reset to the factory default).

1. Press and release the programming switch to select installation

mode.

Press the switch to alternate between the two modes (only standard

mode should be used).

1 ﬂash, pause, I ﬂash, pause = (This mode is not used)

2 ﬂashes, pause, 2 ﬂashes, pause = Standard installation mode

2. Once your installation mode is selected, press and hold the

programming button until the LED displays a solid green light for two

seconds. Your installation mode is now programmed. Please proceed

to step 2.

NOTE: Should you wish to change the installation mode, follow the

“Factory Reset” instructions.

STEP 2: PROGRAMMING PROCEDURE

1. Insert the key into vehicle ignition.

2. Turn the ignition to the “ON” position and wait for the module LED

to illuminate green for 2 seconds. (Note : If module LED remains

illuminated red after 10 seconds elapsed time, turn the key to “OFF”

and repeat programming procedure )

3. Programming has been completed.

LED DIAGNOSTICS

1. During STEP 2, if the LED ﬂashes red this indicates the wire

connections are incorrect.

2. Once programming has been completed, if the LED ﬂashes red,

the module failed to learn correctly. Reset module and repeat the

programming procedure.

3. When the remote starter is engaged, the LED will ﬂash green to

indicate the module has been correctly programmed. If the LED

remains illuminated red, the device is incorrectly programmed.

FACTORY RESET

1. Unplug all connectors from the module.

2. Press and hold the programming button while inserting either the

4-PIN standard or 4-PIN optional Directed connector.

3. The LED will begin to ﬂash red. Immediately release the

programming button.The LED will turn on solid for 2 seconds to

conﬁrm module reset.

4. Plug remaining connectors and return to:

STEP 1: SELECT INSTALLATION MODE.

VEHICLE COMPATIBILITY & WIRING CROSS REFERENCE CHART

GM/DAEWOO

TYPE 1 & 2 INSTALLS

Transponder Bypass

WARNING! READ MANUAL PRIORTO INSTALLATION

NOTE TO THE INSTALLER:

THIS GUIDE IS INTENDED FOR USE WITH AN 1100F OR 1100XTHAT HAS BEEN UPDATED TO AN 1100GD USINGTHE DIRECTLINK UPDATERTOOL.

DIRECTLINK UPDATER SOFTWARE IS AVAILABLE AT WWW.DIRECTECHS.COM.

NOTICE:The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the

vehicle itself or to the installed device.This device must be installed by a certiﬁed technician.This guide has been written for properly trained technicians; a certain level of

skill and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.

1100X/F-GD

DATA SECURITY THEFT LIGHT

Year Pin Ignition

Wire

Pin Data Wire Conn Data Wire Connector Location Pin Theft Light Wire Conn Theft Light Connector Location Type

Chevrolet Aveo (LS) 2004 - 06 1 Pink 6 Black/White D 7 PIN connector at Key Barrel 1

Chevrolet Aveo 5 (LS) 2004 - 06 1 Pink 6 Black/White D 7 PIN connector at Key Barrel 1

Chevrolet Epica (LS/LT) 2004 - 06 7 Green/Black E 15 PIN connector at BCM 20 Yellow/Black F 30 PIN connector at BCM 2

Suzuki Swift 2004 - 06 1 Pink 6 Black/White D 7 PIN connector at Key Barrel 1

Suzuki Verona 2004 - 06 7 Green/Black E 15 PIN connector at BCM 20 F 30 PIN connector at BCM 2

Pontiac Wave 2004 - 06 1 Pink 6 Black/White D 7 PIN connector at Key Barrel 1

Pontiac Wave 5 2004 - 06 1 Pink 6 Black/White D 7 PIN connector at Key Barrel 1

TYPE 1 WIRING DIAGRAM

PINK- IGNITIONFROMECM

BLACK/WHITE-DATA

IGNITION TO BARREL

OPTIONAL

USE TO ISOLATE OEM ALARM IGNITION PINK WIRE BEHIND CENTER CONSOLE

Front view of connector

BLUE/RED (NC)

BLUE/YELLOW (NC)

GREEN/RED (NC)

GREEN/YELLOW (NC)

GRAY/RED - DATA

GRAY/YELLOW (NC)

ORANGE (NC)

PINK/BLACK - IGNITION OUT

PINK - IGNITION INPUT

WHITE/BLACK - ALARM IN ECM

WHITE/RED - ALARM OUT FUSE

WHITE (NC)

RED - 12V

BLACK - GROUND

NO WIRE (NC)

BLUE/WHITE - STATUS OUTPUT REMOTE

STARTER

If the ignition wire (located behind

center console) is interupted by the

Directed module, there is no need

to override the vehicle factory alarm.

This installation method will ensure

your factory keyfob will at all times

function normally (including during

remote start).

Please refer to the Vehicle Wiring Cross Reference Chart to identify vehicle-speciﬁc pin locations & wire colors.

TYPE 2 WIRING DIAGRAM

Please refer to the Vehicle Wiring Cross Reference Chart to identify vehicle-speciﬁc pin locations & wire colors.

LIMITED ONE-YEAR CONSUMER WARRANTY

For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security accessory product, Directed Electronics. (hereinafter “DIRECTED”) promises to the original purchaser, to repair

or replace (at DIRECTED’s election) with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal

use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer in the United States; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible

copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name, date of purchase and complete product and Part description.

This warranty is non-transferable and is automatically void if the Part has been modiﬁed or used in a manner contrary to its intended purpose or if the Part has been damaged by accident, abuse, unreasonable use,

neglect, water, theft, improper service, installation or other causes not arising out of defect in materials or construction. This warranty is automatically void if any Part has had the serial number defaced, altered, or

removed. This warranty is automatically void if the Part has had Repair Service performed by anyone other than the Directed Repair Department. This warranty does not cover damage to any Part caused by installation

or removal of the Part or any system related thereto. This warranty does not cover labor costs for the removal or reinstallation of the Part.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICU-

LAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT PERMITTED BY LAW; AND DIRECTED NEITHER ASSUMES

NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LI-

ABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL

BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY

CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHAT-

SOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC

OPPORTUNITY AND THE LIKE.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you speciﬁc legal rights and you may also have

other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.