Directed Electronics 474A User manual

i
© 2010 Directed Electronics. All rights reserved.
Congratulations
Congratulations on the purchase of your state-of-the-art keyless entry
and remote start system. Reading this Owner’s Guide prior to using
your system will help maximize the use of your system and its many
features. For more information please visit us online at:
www.automatecarsecurity.com.
For any additional questions please contact your authorized Directed
dealer or Directed at 1-800-753-0600. Additional support is also
available at:
http://support.directed.com.
What's included
• Two 4- button remote controls (P/N 474A)
• Your warranty registration card
• Quick reference card
• This owner's guide
!
0890
CODES
EZSDEI474V
66
FCC ID:
BATTERY: CR2032
RPN 474A 2
Warranty
Card
Owner’s
Guide
Quick
Reference Card
Gf
!
0890
CODES
EZSDEI474V
66
FCC ID:
BATTERY: CR2032
RPN 474A 2
G4103A 2010 07

ii © 2010 Directed Electronics. All rights reserved.
Important information
Government Regulations and Safety information
Read the Government Regulations and Warning! Safety
First sections of this manual prior to operating this system.
Warning! Failure to heed this information can result in
death, personal injury or property damage and may also
result in the illegal use of the system beyond its intended
purpose.
Your warranty
Your system comes with a warranty. Please make sure you receive
the warranty registration card and proof of purchase from your dealer
indicating the product was installed by an authorized Directed dealer.
Your product warranty must be validated within 10 days of purchase.
You can validate online at: www.prodregister.com/automate or com-
plete and return the warranty registration card.
Replacement remote controls
If additional remote controls are desired, please see your authorized
dealer or visit us at www.directedstore.com to order. Your 1-way re-
placement part number is 474A.

1
© 2010 Directed Electronics. All rights reserved.
Contents
Congratulations .................................................................................................i
What's included .............................................................................................i
Important information ........................................................................................ii
Your warranty...........................................................................................ii
Replacement remote controls ......................................................................ii
Getting Started .................................................................................................2
System maintenance ..................................................................................2
Battery replacement ..................................................................................2
Remote control functions.....................................................................................3
Standard configuration ..............................................................................3
Using the system .............................................................................................5
Locking ....................................................................................................5
Unlocking ................................................................................................5
Disabling (optional) Starter Kill ..................................................................5
Panic Mode .............................................................................................6
Remote Start .............................................................................................6
Rear Defogger (optional) ..........................................................................8
Valet Take-Over ........................................................................................9
Car Finder ...............................................................................................9
Timer Mode ...........................................................................................10
Starter Anti-Grind Circuitry .......................................................................11
Disabling the Remote Start system .............................................................11
Owner Recognition .........................................................................................12
Rapid Resume Logic ........................................................................................12
Programming Options ......................................................................................13
Glossary of Terms............................................................................................14
Convenience Expansions .................................................................................15
Government Regulations ..................................................................................16
Warning! Safety first .......................................................................................17
Caution .................................................................................................18
Patent information ...........................................................................................19

2© 2010 Directed Electronics. All rights reserved.
Getting Started
System maintenance
The system requires no specific maintenance beyond battery replace-
ment for the remote controls. Your remote is powered by a coin cell
battery (3V CR2032) that lasts approximately one year under normal
use. When the battery begins to weaken operating range is reduced
and the LED on the remote dims.
Battery replacement
Locate the small slot on the side of the remote control. Insert a small
slotted screwdriver or equivalent tool into slot and pry the case apart.
Replace battery while verifying the correct polarity and then snap case
together.

3
© 2010 Directed Electronics. All rights reserved.
Remote control functions
The remote buttons are used to send commands to the system. The but-
tons indicated below are for standard configuration.
Standard configuration
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Button
The lock function is controlled by pressing
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote control for
one second. When held for more than 1.5 seconds, Panic is activated.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Button
The unlocking function is controlled by pressing
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote con-
trol for one second. You can also turn Panic off with this button.
Button
Silent Mode™, and an optional auxiliary function are controlled by
pressing Silent Mode works by pressing for less than one
second before locking or unlocking.
An optional auxiliary function such as trunk release may be controlled
by pressing and holding for 1.5 seconds.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Button
The remote start function of your system is controlled by pressing this
button for one second.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and Buttons
Car Finder is controlled by pressing these two buttons.

4© 2010 Directed Electronics. All rights reserved.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and Buttons
When simultaneously pressed these buttons control the optional rear
window defogger during remote starting.
Important note: Defogger is an optional feature. Additional parts and
labor may be required. See your Directed dealer for details.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Buttons
Timer mode is activated when these buttons are pressed simultaneously.

5
© 2010 Directed Electronics. All rights reserved.
Using the system
Locking
Pressing
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
for one second locks the system (if the door locks are con-
nected). The horn honks and the parking lights flash once to confirm the
system is locked. The Failsafe® Starter Kill also activates and prevents
the vehicle’s starter from cranking.
Important note: Horn honk and Failsafe are both optional features.
Unlocking
Pressing
AUX
AUX
for one second unlocks the doors (if connected). The horn
honks twice and the parking lights flash twice to confirm unlocking of
the system. The Failsafe Starter Kill is deactivated.
Disabling (optional) Starter Kill
If your remote control is lost or damaged, you can manually override
the starter kill. To do this, you must have the ve hi cle's ignition key and
know where the Valet button is located. Be sure to check with the in-
staller for the location of the Valet button.
To override the starter kill, turn the ignition on and press and release
the valet button once within10 seconds. The vehicle should start. If it
does not start, you may have waited too long; turn the ignition off and
repeat the process.
Location of Valet button: ____________________

6© 2010 Directed Electronics. All rights reserved.
Panic Mode
If you are threatened in or near your vehicle, you can attract attention
by trig ger ing the system with your remote control. Press
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
for 1.5
seconds to enter Panic Mode. In Panic Mode, the horn will honk and
the parking lights will flash for 30 seconds. To stop Panic Mode at
any time, press
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
, or
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote control.
Note: In order for Panic Mode to be effective, the vehicle’s horn (or
optional siren) and the vehicle's parking lights must be connected.
Remote Start
This feature allows you to remotely start and run your vehicle for a
pro gram ma ble period of time. This makes it possible to warm up the
engine, and adjust the interior tem per a ture of the ve hi cle with the cli-
mate control system. If interior heating or cooling is desired, the climate
controls must be preset, and the fan blower must be set to the desired
level prior to remote starting the vehicle.
Sat mode,
bank selector
AUDIO
PWR
1 2
REW FF
PLAY/PROG NR
3 4 5 6
DISC- DISC+
11:53
XM1-1 CH-001
CH
VOL
SCAN SOUND
AM/FM
CD/AUX
SAT
RADIO
SEEK
SKIP
RPT
DISP -
MODE
A.SEL
RDM
TUNE
AUTO
OFF
DUAL
A/C MODE
Channel control
Category
Control
Text selector.
Hold for 10sec to toggle
channel or category
tune modes.
Toggles
Scan mode
Bank and
present
indicator
Channel
and text
indicator
Preset 1-6.
Hold until beep to
save to a preset.
CATEGORY
Tune mode
indicator
MODE
DUAL
OFF
AUTO
MAP/
GUIDE MENU SETUP
INFO ZOOM CANCEL AUDIO
AUTO
MODE
A/C
LOAD
DISC
TAPE AM/FM DISP
MODE
SCAN RPT A.SEL/RDM - SEEK +
123 4 56
DISC- DISC+
VOL
PWR
PUSH
TUNE
SOUND
PUSH
XM1-1
VOL
CH
CHANNEL
CATEGORY
NAME
TITLE
:
:
:
:
1
CH
2
CH
3
CH
6
CH
5
CH
4
CH
MODE SCAN SOUND
001 - HITS1
POP
MUSIC NAME
MUSIC TITLE
Channel control
Category
Control
001 014 018
040 065 115
Toggles between
channel and
category modes
Bank and
present
indicator
Upper display
text mode
selector
Sat mode
and bank
selector
Preset 1-6.
Press until
beep to save
to a preset.
Channel and text
Indicator fields
Toggles
Scan mode
Tune mode
indicator
ANTENNA
SC OUTPUT
Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator
Headunit bus cable SiriusConnect Cable
HON-SC1
Honda Bus
Compatible
Translator
Warning! (1) Never remote start your vehicle
when the keys are in the ignition, except when
performing Valet Take-Over, and (2) Never
start the vehicle if it is not in PARK or NEUTRAL
To remote start the vehicle:
• Press the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
button on the remote control for 1 second.
• The parking lights flash to confirm that the vehicle is attempting to
start. In gasoline vehicles the engine will start 4 seconds after the
parking lights flash, in diesel vehicles the engine starts after the
WAIT-TO-START timer has expired.

7
© 2010 Directed Electronics. All rights reserved.
• Once the vehicle has started, it will run for the pre- pro gram med
period of time (12, 24, or 60 minutes) or until a shutdown input
is trig gered.
Sat mode,
bank selector
AUDIO
PWR
1 2
REW FF
PLAY/PROG NR
3 4 5 6
DISC- DISC+
11:53
XM1-1 CH-001
CH
VOL
SCAN SOUND
AM/FM
CD/AUX
SAT
RADIO
SEEK
SKIP
RPT
DISP -
MODE
A.SEL
RDM
TUNE
AUTO
OFF
DUAL
A/C MODE
Channel control
Category
Control
Text selector.
Hold for 10sec to toggle
channel or category
tune modes.
Toggles
Scan mode
Bank and
present
indicator
Channel
and text
indicator
Preset 1-6.
Hold until beep to
save to a preset.
CATEGORY
Tune mode
indicator
MODE
DUAL
OFF
AUTO
MAP/
GUIDE MENU SETUP
INFO ZOOM CANCEL AUDIO
AUTO
MODE
A/C
LOAD
DISC
TAPE AM/FM DISP
MODE
SCAN RPT A.SEL/RDM - SEEK +
123 4 56
DISC- DISC+
VOL
PWR
PUSH
TUNE
SOUND
PUSH
XM1-1
VOL
CH
CHANNEL
CATEGORY
NAME
TITLE
:
:
:
:
1
CH
2
CH
3
CH
6
CH
5
CH
4
CH
MODE SCAN SOUND
001 - HITS1
POP
MUSIC NAME
MUSIC TITLE
Channel control
Category
Control
001 014 018
040 065 115
Toggles between
channel and
category modes
Bank and
present
indicator
Upper display
text mode
selector
Sat mode
and bank
selector
Preset 1-6.
Press until
beep to save
to a preset.
Channel and text
Indicator fields
Toggles
Scan mode
Tune mode
indicator
ANTENNA
SC OUTPUT
Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator
Headunit bus cable SiriusConnect Cable
HON-SC1
Honda Bus
Compatible
Translator
Warning! It is unsafe to operate a vehicle’s motor in a
garage or other closed off area. Breathing the ex haust
from the vehicle is hazardous to your health. Never
activate the remote start in an enclosed space.
When you are ready to drive the vehicle:
1. Insert the ignition key and turn it to the ON (not the START)
po sition.
2. Press the brake pedal. The remote start system shuts down and the
engine continues to run because the ignition has been turned on.
Note: If the brake pedal is pressed before the key is in the ON position,
the engine will shut down.
While the vehicle is running during remote start operation, the system
monitors the ve hi cle and automatically shuts down the engine if it receives
any of the following shut-down inputs:
• The brake pedal is pressed.
• The hood is opened.
• The shutdown toggle switch is put into the OFF position.
• The pre-programmed run time (12, 24, or 60 minutes) has elapsed.
• Remote control button
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
is pressed once.

8© 2010 Directed Electronics. All rights reserved.
Rear Defogger (optional)
To turn the rear defogger Off and On:
1. Simultaneously press & release the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
+
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
+ buttons on
the remote control.
2. The lights flash 2 times when the defogger is turned On, and 3
times when it is turned Off.
If the rear defogger is On, it activates when the vehicle is remote
started, if it is Off it does not activate when remote started.
Note: When turning the defogger Off, if remote start is On the lights
turn Off then flash 2- times before returning to normal. The defogger
output is no longer active.
When turning the defogger On, if remote start is On the lights turn Off
then flash 3-times before returning to normal. The defogger output will
activate as programmed.

9
© 2010 Directed Electronics. All rights reserved.
Valet Take-Over
The Valet Take-Over feature allows the vehicle to remain running after
the key has been removed from the ignition. This feature is useful for
occasions when you wish to exit and lock the vehicle for short periods
of time, but would like to leave the engine running and the climate
controls on.
To perform Valet Take-Over:
1. Before turning off the engine, press and release
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote
control for 1 second or press and release the optional momentary
switch, then wait 5 seconds.
2. Turn the ignition key to the OFF position. The engine will stay run-
ning until the pre- pro gram med time has elapsed or a shutdown
input is received. (See the previous Remote Start section for a
complete list of shut-down inputs.)
Important: This
feature will not work if the brake pedal is being pressed.
Car Finder
Car finder allows you to locate your vehicle, by having the system flash
the parking lights.
To activate:
1. Press and release the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and buttons at the same time.
2. The lights flash 5 times slowly allowing you to locate your ve-
hicle.

10 © 2010 Directed Electronics. All rights reserved.
Timer Mode
When you activate timer mode the system automatically starts the ve-
hicle every three hours for a maximum of 6 starts. The pre-programmed
engine runtime is 12 minutes.
• Press
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
simultaneously to activate timer mode. The
parking lights flash four times, and after a 1 second delay the
engine starts.
• To shutdown the engine, press the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
button for 1 second. The
system remains in timer mode and continues to start every 3 hours
unless cancelled by turning on the ignition, activating the brake, or
moving the shutdown toggle switch to the Off position.
• The parking lights flash 4 times indicating timer mode is exited.
Important! Timer Mode should be used only in open
areas. Never start and run the vehicle in an enclosed
space such as a garage or carport.

11
© 2010 Directed Electronics. All rights reserved.
Starter Anti-Grind Circuitry
Whenever the vehicle is remote started, advanced anti-grind circuitry
prevents the starter from engaging, even if the key is turned to the start
position. This prevents damage to the starter motor if the key is turned to
the start position during remote start operation.
Note: Anti-grind circuitry only works when the remote start system is op-
er at ing the motor and the optional Failsafe® Starter Kill relay is installed.
Disabling the Remote Start system
This feature allows your system's remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the shutdown toggle
switch to the OFF position. The switch can be installed in a location
of your choice. Check with your installer for recommended locations.
Location Of Shutdown Switch _________________________

12 © 2010 Directed Electronics. All rights reserved.
Owner Recognition
Owner Recognition is a revolutionary feature avail able only from Di-
rected. Using a Directed Bitwriter®, hand-held programming tool, your
dealer can program many of the system settings. It is possible to pro-
gram different settings for each trans mit ter used with the system. Then,
when ev er a specific transmitter is used, the system recalls the settings
assigned to that transmitter. Owner Rec og ni tion lets up to four users of
the system have different settings that meet their specific needs. It is al-
most like having four separate systems in your vehicle, one for each user.
Important: Owner Recognition cannot be programmed without a Bit-
writer® and the necessary soft ware. Check with your dealer for more
information.
Rapid Resume Logic
This Directed Electronics system will store its current state to non-volatile
memory. If power is lost and then reconnected the system will recall the
stored state from memory. This means if the unit is in Locked Mode and
the battery is dis con nect ed for any reason, such as servicing the car,
when the battery is re con nect ed the unit will still be in Locked Mode.
This applies to all states of the system.

13
© 2010 Directed Electronics. All rights reserved.
Programming Options
Programming options control your system's normal, operational set-up.
Most options do not require additional parts, but some may require ad-
ditional installation labor. This system's programming options are listed
below, with the factory default settings in
bold :
•
12 , 24, or 60 minute run time. your system can be programmed
to allow the vehicle to run for 12, 24, or 60 minutes when remote
started. Can be programmed from 1 -60 minutes.
• 3, 6, 9, or
12 minute timer mode run time. Your system can be
programmed to allow the vehicle to run for 3, 6, 9, or 12 minutes
when remote started in timer mode. Can be set from 1-16 minutes
by your installer.
• Comfort closure is a programming option which closes the ve-
hicle’s windows after remote locking.
• Parking lights flashing or constant. Your system can be pro-
grammed to either flash or to turn on the parking lights constantly
during the entire remote start operation.
• Ignition switch-controlled door-locking
on or Off. With this feature
on, the doors will lock 3 seconds after the ignition key is turned on,
and unlock when the ignition key is turned off.
• The horn honk confirmations for locking and unlocking can be
programmed
on or Off. In order for this feature to work, it must be
connected to the system.

14 © 2010 Directed Electronics. All rights reserved.
Glossary of Terms
Control Unit: The “brain” of your system. Usually hidden underneath the
dash area of the vehicle. It houses the microprocessor which monitors
your vehicle and controls all system functions.
Failsafe® Starter Kill: An optional automatic switch controlled by your
system which prevents the vehicle’s starter from cranking whenever the
system is locked. The vehicle is never prevented from cranking when
the system is unlocked, in Valet Mode, or if the starter kill switch itself
fails. Your system has feature-ready circuitry for the starter kill, however
installation may require additional labor and parts.
LED: indicator on your remote control that lights up when a button is
pressed.
Remote control: A hand-held device which operates the various func-
tions of your system.
Valet Button: A small push button mounted at a discretionary location
inside the vehicle. It is used to override the Failsafe® Starter Kill when a
remote control is lost or damaged.

15
© 2010 Directed Electronics. All rights reserved.
Convenience Expansions
Listed below are expansion options available for use with your system.
Some options may require additional parts and/or labor. Please con-
sult with your dealer for a complete list of options available for use with
this system.
Power Door Lock Control: Your system is capable of controlling many
types of power door lock systems; however, some door lock systems
may require extra parts. Consult with your dealer to determine which
type of locks your vehicle uses. The system can be programmed to lock
the doors when the ignition is turned on and to unlock them when the
ignition is turned off.
Power Trunk Release: The system’s auxiliary output can be programmed
to operate a factory power release for the vehicle's trunk or hatch. If
the factory release is not power-activated, Directed Electronics 522T
trunk-release solenoid can often be added.
Power Window Control: Power window control is provided with Di-
rected Electronics 529T or 530T systems. The 529T system will roll
up two windows automatically when the system is locked, or roll two
windows down by using the remote control. The 530T will roll two
windows both up and down. The 530T also provides one touch switch
operation.

16 © 2010 Directed Electronics. All rights reserved.
Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
This device complies with the Industry Canada Radio Standards Specification
RSS 210. Its use is authorized only on a no-interference, no-protection basis; in
other words, this device must not be used if it is determined that it causes harm-
ful interference to services authorized by IC. In addition, the user of this device
must accept any radio interference that may be received, even if this interference
could affect the operation of the device.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

17
© 2010 Directed Electronics. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal
from the remote control. Therefore, never operate the system in an enclosed area
or partially enclosed area without ventilation (such as a garage). When parking
in an enclosed or partially enclosed area or when having the vehicle serviced,
the remote start system must be disabled using the installed toggle switch. It is
the user’s sole responsibility to properly handle and keep out of reach from chil-
dren all remote control devices to assure that the system does not unintentionally
remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE
DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED
OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES
REMAIN CLOSED. These precautions are the sole responsibility of the user.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral safety feature of the
vehicle periodically checked, wherein the vehicle must not remotely start while
the car is in gear. This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the product installation
guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.
After the remote start module has been installed, contact your authorized dealer
to have him or her test the remote start module by performing the Safety Check
outlined in the product installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit has not been

18 © 2010 Directed Electronics. All rights reserved.
properly installed. The remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle does not start in gear.
All installations must be performed by an authorized Directed dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-
ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-
THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR
PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Caution
This product is designed for fuel injected, automatic transmission ve-
hicles only. Use of this product in a standard transmission vehicle is
dangerous and contrary to the product's intended use.