Directed Electronics 5301 User manual

Responder LE Model 5301
Remote Start Keyless Entry
Owner’s Guide
© 2008 Directed Electronics, Vista, CA
G4202V 2008-05

Contents
Government regulations .....................................................................................5
Warning! Safety first .........................................................................................6
What’s included................................................................................................9
Important information ........................................................................................9
Your warranty...........................................................................................9
Replacement remotes.................................................................................9
Responder LE 2-way remote..............................................................................10
1-way companion remote.................................................................................11
Transmitter configuration..........................................................................11
Out of range notification..........................................................................16
System maintenance................................................................................16
Low battery indicator ..............................................................................16
Remote control progamming ....................................................................17
Multi-car control capability.......................................................................19
Locking the vehicle..................................................................................20
Unlocking the vehicle ..............................................................................20
Using the remote start ......................................................................................22
Remote starting your vehicle.....................................................................22
Runtime check .......................................................................................23
Manual transmission vehicles ...................................................................24
Timer mode............................................................................................25
Turbo timer mode....................................................................................26
Smart start activation...............................................................................27
Cabin temperature .................................................................................29
Turning on the rear defogger....................................................................29
Valet take-over .......................................................................................30
Safety features................................................................................................31
Optional starter anti-grind circuitry............................................................31
Disabling the remote start system ..............................................................31
Diagnostics ....................................................................................................32
Locking .................................................................................................32
Unlocking ..............................................................................................32
Owner recognition ..........................................................................................33
Rapid resume logic..........................................................................................33
Power saver mode...........................................................................................33
System...................................................................................................33
2-way remote .........................................................................................34
Programming options.......................................................................................34
Convenience expansions..................................................................................35
Glossary of terms............................................................................................36
Quick reference guide .....................................................................................37
Limited lifetime consumer warranty ....................................................................39

5
© 2008 Directed Electronics. All rights reserved.
Government regulations
This device complies with Part 15 of FCC rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television, which can be determined by
turning the equipment Off and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which•
the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.•
To satisfy FCC RF exposure compliance requirements, this device should be used
in hand-held, hand operated configurations only. The device and its antenna
must maintain a separation distance of 20 cm or more from the person’s body,
except for the hand and wrists, to satisfy RF exposure compliance. This device
is designed to be used in a person’s hands and its operating configurations do
not support normal transmissions while it is carried in pockets or holsters next to
a persons’ body.

6© 2008 Directed Electronics. All rights reserved.
This device complies with the Industry Canada Radio Standards Specification
RSS 210. Its use is authorized only on a no-interference, no-protection basis; in
other words, this device must not be used if it is determined that it causes harm-
ful interference to services authorized by IC. In addition, the user of this device
must accept any radio interference that may be received, even if this interference
could affect the operation of the device.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal
from the remote control transmitter. Therefore, never operate the system in an
enclosed area or partially enclosed area without ventilation (such as a garage).
When parking in an enclosed or partially enclosed area or when having the
vehicle serviced, the remote start system must be disabled using the installed
toggle switch. It is the user’s sole responsibility to properly handle and keep out
of reach from children all remote control transmitters to assure that the system
does not unintentionally remote start the vehicle. THE USER MUST INSTALL A
CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJA-
CENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING
AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE
AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole
responsibility of the user.
Remote starters on manual transmission vehicles operate differently than those
with automatic transmission because you must leave your car in neutral. You
must read this Owner’s Guide to familiarize yourself with the proper procedures
regarding manual transmission remote starters. If you have any questions, ask
your installer or contact Directed at 1-800-753-0600.

7
© 2008 Directed Electronics. All rights reserved.
Before remote starting a manual transmission vehicle, be sure to:
Leave the vehicle in neutral and be sure no one is standing in front or•
behind the vehicle.
Only remote start on a flat surface•
Have the parking brake fully engaged•
Warning! It is the responsibility of the owner to ensure the parking/
emergency brake properly functions. Failure to do so can result in personal
injury or property damage. We recommend the owner have the parking/
emergency brake system inspected and adjusted by a qualified automotive
shop biannually.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral safety feature of the
vehicle periodically checked, wherein the vehicle must not remotely start while
the car is in gear. This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the product installation
guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.
After the remote start module has been installed, contact your authorized dealer
to have him or her test the remote start module by performing the Safety Check
outlined in the product installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit has not been
properly installed. The remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle does not start in gear.
All installations must be performed by an authorized Directed dealer.

8© 2008 Directed Electronics. All rights reserved.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-
ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-
THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR
PAY FOR INSTALLATION OR REINSTALLATION COSTS.
This product is designed for fuel injected vehicles only. Use of this product in a
standard transmission vehicle must be in strict accordance with this guide.
This product should not be installed in any convertible vehicles, soft,or hard top
with a manual transmission. Installation in such vehicles may pose certain risk.

9
© 2008 Directed Electronics. All rights reserved.
What’s included
One five-button/2-way Supercode Responder LE remote control•
One five-button/ 1-way Supercode remote•
The control module (installed out-of-sight)•
Control center with integrated status LED and Valet override switch•
A remote start defeat toggle switch•
Window decals•
Your warranty registration•
Important information
Congratulations on the purchase of your state-of-the-art remote start and key-
less entry system. Due to the complexity of this system, it must be installed by
an authorized dealer only. Installation of this product by anyone other than an
authorized dealer voids the warranty. All dealers are provided with a preprinted
dealer certificate to verify authorization.
By carefully reading this Owner’s Guide prior to using your system, you will
maximize the use of this system and its features. You can print additional or
replacement copies of this manual by accessing our web site at www.directed.
com.
➤Your warranty
Your warranty registration must be completely filled out and returned within 10
days of purchase. Your product warranty will not be validated if your warranty
registration is not returned. Make sure you receive the warranty registration from
your dealer. It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
➤Replacement remotes
Your system comes with one Responder LE remote control (P/N 7251) and one
remote control (P/N 7152). If additional remotes are desired, please see your
authorized dealer or visit www.directedstore.com to order.

10 © 2008 Directed Electronics. All rights reserved.
Responder LE 2-way remote
8
1
2
3
4
5
9
A U X
6
7
Feature Description
1 Lock button Press for one second to lock.
2 Unlock button Press for one second to unlock.
3 Remote start
button
Press for one second to activate remote
start.
4 Auxiliary
button
Press and hold for 1.5 second to activate
optional trunk release.
5 Function
button
Allows access to programming and
modifies operation of the other buttons.
6 Label Back of remote has label to identify the
remote as 2-way or 1-way.
7 Battery Door Remove to access batteries when
necessary. For more detail, see p. 16
8 Transmit indicator
9 LED indicators Flashes to indicate function confirmation
Note: If Keypad Lock is On, press and then press
1
3
4
5
6
2
A U X
8
7
1
2
3
4
5
6
1-800-274-0200
RPN 7152X
IC: 1513A-7152
FCC ID:EZSDEI7152
BATTERY: CR2032
7
8
7
8
1
2
3
4
5
6
to exit.

11
© 2008 Directed Electronics. All rights reserved.
1-way companion remote
8
2
3
4
5
1
A U X
7
6
Note: See call-out table for 2-way
➤Transmitter configuration
Button
Level Direct Access
A U X
x 1
A U X
x 2
A U X
x 3
A U X
x 4
A U X
Lock Silent Lock
A U X
Unlock Silent Unlock Valet Mode Car Finder
A U X
Remote Start Reset
Runtime
Timer Mode Smart Start Rear
Defogger
A U X
Trunk Release AUX 1 AUX 2 AUX 3
A U X
Function Shift* Cabin
Temperature
request*
(2-way only)
Lock Status*
(2-way only)
Runtime
Check*
(2-way only)
* button must be pressed and held to access state

12 © 2008 Directed Electronics. All rights reserved.
Button
A U X
Lock
Command : Press one time to Lock
Feedback : Lock LED flashes for 1-sec with 1 beep.
Notes : Press/hold for 1.5 seconds to Lock the system and then acti-
vate the Panic output*
A U X
Unlock
Command : Press one time to Lock
Feedback : Unlock LED flashes for 1-sec and remote beeps twice
Notes :
A U X
Remote
Start
Command : Press one time to activate Remote Start
Feedback : Remote Start LED flashes for 3-secs, remote start tones.
Notes :
A U X
AUX
Command : Press and hold for 1.5 seconds to activate the Trunk Re-
lease.
Feedback : The AUX LED turns on for 3-secs and AUX activation tone
sounds.
Notes : This is an optional feature. See your sales rep/installer for
details.
A U X
Function
Shift
Command : Press 1 to 4 times. ( See Function shift table.)
Feedback : LED indicators turn on (according to the feature command)
Notes : Each Press then release, shifts the function of the command
button.
Note: Feedback is available on the 2-way remote only.
* Horn honk is an optional feature. The panic and horn honk feature is avail-
able when this option is installed.
Pressing more than one button simultaneously generates an Error tone and the
"Function" LED turns on.

13
© 2008 Directed Electronics. All rights reserved.
Feature List:
Silent lock
Command :Press
A U X
one- time and then press
A U X
Feedback :Lock LED flashes for 1-sec
Notes :Locks the system without horn honks*
Silent unlock
Command :Press
A U X
one- time and then press
A U X
.
Feedback :Unlock LED flashes for 1-sec
Notes : Unlocks the system without horn honks*
Runtime reset
Command :Press
A U X
one-time and then
A U X
.
Feedback :Remote start On tones sound.
Notes : Re-starts the remote start runtime counter if remote start
is active. Note: If remote start is not active, the 2-WAY
remote will respond with error tone.
Aux 1
Command :Press
A U X
one time and then press
A U X
.
Feedback :The Aux LED turns on for 3-secs, Aux activation tone
sounds.
Notes : This is an optional feature. See your sales rep/installer
for details.
Cabin temperature
Command :Press
A U X
one time, then Hold for 1.5 seconds.
Feedback :Screen will display current cabin temperatue.
Notes :Cabin temperature is displayed on the remote. LED lights
turn on to indicate a range. (See p.29)

14 © 2008 Directed Electronics. All rights reserved.
Valet mode
Command :Press
A U X
two-times and then
A U X
.
Feedback :Remote beeps 1 to 2 times when entering Valet mode.
Notes :To enter or exit Valet mode, even if Locked. When
entering Valet Mode the remote beeps one-time. When
exiting Valet Mode the remote beeps two-times.
Timer mode
Command :Press
A U X
two-times and then

ALL
.
Feedback :Remote start LED turns on.
Notes :Enables or disables the remote start timer mode.
Aux 2
Command :Press
A U X
two times and then press
A U X
.
Feedback :The AUX LED turns on for 3-secs, and AUX activation
sounds.
Notes :This is an optional feature. See your sales rep/installer
for details.
Car finder
Command :Press
A U X
three-times and then
A U X
.
Feedback :Remote beeps 1 short beep, the vehicle emits 1 long
horn honk*, and the parking lights flash 10 times.
Notes :Lock/Unlock cancels the parking light flashes.
Smart start
Command :Press
A U X
three-times and then press
A U X
.
Feedback :Remote start LED turns on, with 1 beep for enable or 2
beeps for disable.
Notes :Enables or disables the Smart Start feature.

15
© 2008 Directed Electronics. All rights reserved.
Aux 3
Command :Press
A U X
three times and then press
A U X
.
Feedback :The AUX LED turns on for 3-secs, AUX activation tone
sounds.
Notes :This is an optional feature. See your sales rep/installer
for details.
Runtime check
Command :Press
A U X
three-times, and then Hold for 1.5 seconds.
Feedback :Remote start On tones sound.
Notes :Runtime remaining is displayed as per the LED on the
remote. (See page 23). If the remote start is not active
the 2-way responds with an error tone.
Rear defogger
Command :Press
A U X
four times, and then
A U
X
. (Only after remote
start is on.)
Feedback :Remote start LED on, 1 beep.
Notes :Manually turns on the defogger when remote start is
on.

16 © 2008 Directed Electronics. All rights reserved.
➤Out of range notification
If a command is issued from the remote, but the remote is beyond the range
of the vehicle to receive the command, the remote will respond with an out-of
range notification. If this occurs, the transmit indicator on the remote flashes
rapidly, the key LED turns on, and the remote emits the error tone sounds.
Since conditions will vary in different areas (i.e.: Weather, RF interference, etc)
range may be affected and require you to be closer to the vehicle for successful
transmission.
➤System maintenance
The system requires no specific maintenance. Your remotes are powered by
small coin cell lightweight 3-volt lithium batteries that last approximately one
year under normal use. The 2-way remote uses two CR2016 cell batteries and
the 1-way remote uses one CR2032 cell battery. When the battery begins to
weaken, the operating range is reduced.
➤Low battery indicator
When the batteries are low on the 2-way remote it emits two groups of beeps,
the LED flashes, and the system emits an additional honk when unlocking to let
you know its time to change the battery. When the battery is low on the 1-way
remote, the remote responds the same, but without the LED flash.
Note: The Lock/Unlock confirmations should be programmed On,and the op-
tional horn honk installed, for the system to emit any additional honks during
unlocking. Ask your authorized dealer if you have any questions.

17
© 2008 Directed Electronics. All rights reserved.
➤Remote control programming
The Responder LE 2-way remote control has menus for programming the re-
mote to the system control module and for configuring the remote control user
features.
Before you start make sure the keypad is unlocked. (See page 11)
To program the remote user features:
Press and hold the1.
A U X
button on the remote for 12 seconds. (ignore the
car indicator at 3 seconds). The remote emits one long beep, and the
transmit LED turns on to indicate the Main Menu.
Press and hold the2. button for 1. 5 seconds: The remote beeps two-
times. You are now in the Remote Configuration menu.
The Lock, Unlock, Remote Start and Aux LEDs turn on and/or blink to indicate
the current remote feature configuration. When the LED is On, the feature is
On.
To configure the remote control features:
Press and release the command button. The LED next to the button turns On or
Off. The remote beeps to indicate the feature configuration.
Press the button to access the Auto keypad lock feature. When the
A U X
LED
is off, the keypad does not lock.
Press the button to change the Auto keypad lock feature.
Lock LED On: The keypad lock feature is On. When the•
A U X
LED is on,
the keypad automatically locks 60 seconds after the last button operation
to avoid accidental command operations. When locked, if any command
button is pressed the remote emits an error tone. The companion remote
beeps once when the feature is programmed On.
Lock LED Off: The keypad lock feature is Off and the keypad does not•
lock. The companion remote beeps twice wthen the feature is programmed

18 © 2008 Directed Electronics. All rights reserved.
Off.
If the keypad lock is On, press , and then press
1
3
4
5
6
2
A U X
to unlock the keypad.
Note: If the auto keypad lock feature is programmed On, the remote unlocks
when the vehicle ignition is turned Off. The remote stays unlocked to allow time
to exit and unload the vehicle, and then lock the doors with the remote. When
the
A U X
button is pressed, the keypad auto lock feature resumes normally.
Press the
1
3
4
5
6
2
A U X
button to access and change the Remote Beeps feature.
Unlock LED On: The remote emits beeps normally. The companion remote•
beeps once to confirm the mode change.
Unlock LED Off: The remote does not emit beeps except when program-•
ming. The companion remote beeps twice to confirm mode change.
Unlock LED blinking: The remote emits beeps only if the optional horn honk•
input is hooked up and the factory alarm has been triggered. (This feature
is not available on the 1-way companion remote).
Press the
A U X
button to access and change the Runtime Low Alert feature.
Note: This feature is not available on the 1-way companion remote.
Remote Start LED On: The remote emits feedback output for Runtime Low•
Alert messages.
Remote Start LED Off: The remote ignores Runtime Low Alert•
messages.
These messages are automatically sent while Remote Start is On to alert you
when the runtime remaining is at 3 minutes, and again at 1 minute before shut
down.
Press the
A U X
button to access and change the Page mode/Power saver mode.
Note: Not available on the 1- way companion remote.
Aux LED On: the remote wakes up to listen for messages from the system•
Aux LED blinking: Power saver mode (see Note below)•
Aux LED Off: The remote does not wake up and listen for messages from•
the system to extend battery life. This means the remote does not receive

19
© 2008 Directed Electronics. All rights reserved.
the optional factory alarm trigger pages.
Note: If a remote button is not pressed for more than 72 hours, the remote au-
tomatically goes into sleep mode to extend battery life. It wakes up and resets
each time a button is pressed.
➤Multi-car control capability
You can use the Responder LE 2-way and 1-way companion remote control
system for two cars, with full command capability for both vehicles.
While holding a command button and transmitting,the amber LED at the top of
the remote control flashes in groups to indicate which car is being controlled.
Car 1: 1 flash•
Car 2: 2 flashes•
To change the Car to be operated:
Press/hold the button for 3 seconds or until the remote beeps and the and/
or
1
3
4
5
6
2
A U X
LEDs turn on. This indicates which car the remote currently operates.
Car 1: 1 beep and Lock LED on•
Car 2: 2 beeps and Lock & Unlock LEDs on•
Note: Using the 1-way companion remote, the amber LED flashes and beeps
once for Car 1. The amber LED flashes and beeps twice for Car 2.
To change Car while the LEDs are On:
Press and release the1. button. The LEDs will change to indicate the car
that can be operated.
After you select the car number, press any command button to operate the2.
features. The selected car remains selected until the setting is changed.

20 © 2008 Directed Electronics. All rights reserved.
➤Locking the vehicle
To lock the vehicle, press the button on the remote control.
The horn in the vehicle “honks” one-time, and the parking lights flash one-time. If
the power door locks have been connected, the doors lock.
The system automatically checks for errors when it locks. The 2-way remote
honks one-time and then flashes the LED indicator to confirm locking. If no
lock confirmation is received, the remote emits the out-of-range signal.
If errors are found when locking:
If the door is open when you lock the vehicle, the horn honks once and the park-
ing lights flash. The horn then honks a second time to indicate that the door is
open and the LED on the control center flashes in groups of three
The 2-way remote control sounds a short “error” tone, and the LED indicators
next to the and buttons flash. Note: The optional horn honk and door input
has to be installed for this function.
Locking without the honk (Silent Lock)
Press the button on the remote one-time, and then press the button. The
vehicle locks without the confirmation honk. The parking lights flash one-time.
The 2-way remote flashes the LED to confirm locking. If no lock confirmation
is received, the 2-way remote emits the out-of-range signal.
➤ Unlocking the vehicle
Lock the vehicle normally. Press the button one time. The vehicle horn honks
two-times and the parking lights flash. The 2-way remote beeps two-times and
the LED indicator flashes. The door locks, if connected, unlock. If no unlock
confirmation is received, the 2-way remote emits the out-of-range signal.
UnLocking without the honk (Silent Unlock)
Lock the vehicle normally. Press the button on the remote one-time, and then
press the
1
3
4
5
6
2
A U X
button. The vehicle unlocks without the confirmation honk. The
parking lights flash two-times. The 2-way remote flashes the
1
3
4
5
6
2
A U X
LED to confirm
unlocking. If no unlock confirmation is received, the 2-way remote emits the