Directed Electronics BOA 165B Quick start guide

116655BB
➤
OOwwnneerr’’ss//IInnssttaallllaattiioonnGGuuiiddee

i
© 2004 Directed Electronics, Inc.
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics, Inc. (hereinafter "Directed") promises to the original purchaser to
repair or replace with a comparable reconditioned Directed DIY remote start unit if this
Directed DIY remote start unit (hereinafter "Unit"), excluding without limitation, any
remote transmitters or associated accessories, proves defective in materials or workman-
ship under normal use for the life of the vehicle which the Unit is originally installed.
During this period, so long as the Unit remained installed in the original vehicle, Directed
will at its option, repair or replace this Unit if it is proved defective in workmanship or
material PROVIDED the Unit is returned to Directed's warranty department at One
Viper Way, Vista, CA 92081, along with $20 postage and handling fee, a bill of sale or
other dated proof of purchase bearing the following information: Date of purchase, name
and location of the merchant who sold the Unit, and product description. This warranty
does not cover labor costs for the removal or reinstallation of the Unit. This warranty is
non-transferable and does not apply to any Unit that has been modified or used in a man-
ner contrary to its intended purpose, and this warranty does not cover damage to any Unit
caused by installation or removal of the Unit. This warranty is void if the Unit has been
damaged by accident or unreasonable use, neglect, improper service or other causes not
arising out of defects in materials or workmanship. Directed makes no warranty against
theft of a vehicle or its contents.
THE FOREGOING WARRANTY IS THE EXCLUSIVE PRODUCT WARRANTY,
OTHERWISE, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO
EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MER-
CHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY
EXCLUDED AND DISCLAIMED TO THE MAXIMUM EXTENT ALLOWED BY
LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF
THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. SOME STATES DO NOT ALLOW THE LIMITATION ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.
LIMITATION OF DAMAGES AND LIABILITY. CONSUMER'S REMEDY IS LIM-
ITED TO REPAIR OR REPLACEMENT OF THE UNIT, AND IN NO EVENT
SHALL DIRECTED'S LIABILITY EXCEED THE PURCHASE PRICE OF THE
UNIT. IN ANY EVENT, DIRECTED SHALL NOT BE LIABLE FOR ANY DAM-
AGES INCLUDING, BUT NOT LIMITED TO, ANY DIRECT, INDIRECT, INCI-
DENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, LOST
PROFITS, LOST SAVINGS, OR, TO THE EXTENT ALLOWED BY APPLICABLE
LAW, DAMAGES RESULTING FROM DEATH OR INJURY ARISING OUT OF

ii © 2004 Directed Electronics, Inc.
OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR
INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO
NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT
ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE
RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO
COUNTY, CALIFORNIA.
IIMMPPOORRTTAANNTTNNOOTTEE::
This product warranty is automatically void if its date code or serial number is defaced,
missing, or altered. This warranty will not be valid unless you have completed the war-
ranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the
address listed on the warranty registration card.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Authorized dealer's company name and address
➤Item number

1
© 2004 Directed Electronics, Inc.
ttaabblleeooffccoonntteennttss
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii
wwhhaattiissiinncclluuddeedd............................................................................................................33
iinnssttaallllaattiioonnttoooollss............................................................................................................33
iimmppoorrttaannttiinnffoorrmmaattiioonn..................................................................................................44
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
wwaarrnniinngg!!ssaaffeettyyffiirrsstt......................................................................................................55
pprriimmaarryyhhaarrnneessss((HH//11)),,88--ppiinnccoonnnneeccttoorr........................................................................88
rreellaayywwiirreess66--ccoonnnneeccttoorrss................................................................................................88
uussiinnggLLEEDDtteessttpprroobbee....................................................................................................99
iinnssttaallllaattiioonn..................................................................................................................1100
step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
step 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
step 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
step 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
step 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
step 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
step 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
step 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
step 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ttrraannssmmiitttteerrffuunnccttiioonnss..................................................................................................2266
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CCoonnttrroollMMoodduulleePPrrooggrraammmmiinngg..................................................................................2277
uussiinnggyyoouurrssyysstteemm......................................................................................................2288
warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
remote start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ppiittssttooppmmooddee..............................................................................................................3322
ccooddeehhooppppiinngg®®rree--ssyynncchhrroonniizzee..................................................................................3333
ssyysstteemmeexxppaannssiioonniitteemmss..............................................................................................3344
ttrroouubblleesshhoooottiinngg..........................................................................................................3344
gglloossssaarryyoofftteerrmmss........................................................................................................3366
wwiirriinnggqquuiicckkrreeffeerreenncceegguuiiddee......................................................................................3377
nnootteess..........................................................................................................................3399
qquuiicckkrreeffeerreenncceegguuiiddee..................................................................................................4455

2© 2004 Directed Electronics, Inc.

3
© 2004 Directed Electronics, Inc.
wwhhaattiissiinncclluuddeedd
➤Control Module
➤One 4-Button Transmitter
➤8-Pin Main H/1 Harness
➤6-Relay Wires
➤Shutdown Toggle Switch
➤Hood Pin Switch
➤10 feet of Black Electrical Tape
➤6 Six inch Zip Ties
➤LED Tester
➤Razor Knife
➤CDROM—Do-It-Yourself Installation Video
Additional parts may be required (such as relays or immobilizer).
iinnssttaallllaattiioonnttoooollss
➤Digital Multi-Meter
➤Drill
➤9/32 and 5/16 Drill Bits
➤Screwdrivers
(Phillips and Flathead)
➤Wire Stripper
➤Solder Iron
➤Electrical Tape
➤Pliers
➤Crimping Tool
note: The installation tools listed above may be optional
and those required will vary depending on your vehicle.

4© 2004 Directed Electronics, Inc.
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your remote start system. This
system will allow convenient remote start of your vehicle. Properly
installed, this system will provide years of trouble-free operation.
Please take the time to carefully read this User’s Guide in its
entirety and watch the Do-It-Yourself Installation Video
(CDROM) prior to installing your system.
You can print additional or replacement copies of this manual by
accessing the Directed web site at www.boasecurity.com.
system maintenance
The system requires no specific maintenance. Your transmitter is
powered by a miniature 3-volt battery (type CR2032) that will
last approximately one year under normal use. When the battery
begins to weaken, the operating range will be reduced.
your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Please note that it is necessary to keep your proof of purchase.
➜
➜
important! If you are not comfortable working with elec-
tronics or unfamiliar with the tools required, please con-
tact your local dealer for advice or ask to have the remote
start professionally installed to avoid costly damages.
Failure to properly install the remote starter may result in
property damage, personal injury, or both.

5
© 2004 Directed Electronics, Inc.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
wwaarrnniinngg!!ssaaffeettyyffiirrsstt
The following safety warnings must be observed at all times:
➤When properly installed, this system can start the vehicle via
a command signal from the remote control transmitter.
Therefore, never operate the system in an area that does not
have adequate ventilation. The following precautions are the
sole responsibility of the user; however, the following recom-
mendations should be made to all users of this system:
1. Never operate the system in an enclosed or partially
enclosed area without ventilation (such as a garage).
2. When parking in an enclosed or partially enclosed area
or when having the vehicle serviced, the remote start
system must be disabled using the toggle switch.
3. It is the user's sole responsibility to properly handle and
keep out of reach from children all remote control
➜

6© 2004 Directed Electronics, Inc.
transmitters to assure that the system does not uninten-
tionally remote start the vehicle.
4. TTHHEEUUSSEERRMMUUSSTTIINNSSTTAALLLLAACCAARRBBOONN
MMOONNOOXXIIDDEEDDEETTEECCTTOORRIINNOORRAABBOOUUTTTTHHEE
LLIIVVIINNGGAARREEAAAADDJJAACCEENNTTTTOOTTHHEEVVEEHHIICCLLEE..
AALLLLDDOOOORRSSLLEEAADDIINNGGFFRROOMMAADDJJAACCEENNTT
LLIIVVIINNGGAARREEAASSTTOOTTHHEEEENNCCLLOOSSEEDDOORR
PPAARRTTIIAALLLLYYEENNCCLLOOSSEEDDVVEEHHIICCLLEESSTTOORRAAGGEE
AARREEAAMMUUSSTTAATTAALLLLTTIIMMEESSRREEMMAAIINNCCLLOOSSEEDD..
➤Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. Except when performing the Safety Check
outlined in this user’s guide, (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start
the vehicle with the keys in the ignition. The user will be
responsible for having the neutral safety feature of the vehicle
periodically checked, wherein the vehicle must not remotely
start while the car is in gear. This testing should be performed
by an authorized Directed dealer in accordance with the
Safety Check outlined in this product installation guide. If the
vehicle starts in gear, cease remote start operation immediately
and consult with the Dealer to fix the problem immediately.
➤After the remote start module has been installed, test the
remote start module in accordance with the Safety Check
outlined in this installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The remote

7
© 2004 Directed Electronics, Inc.
start module must be removed or properly reinstalled so that
the vehicle does not start in gear. OOPPEERRAATTIIOONNOOFFTTHHEE
RREEMMOOTTEESSTTAARRTTMMOODDUULLEEIIFFTTHHEEVVEEHHIICCLLEE
SSTTAARRTTSSIINNGGEEAARRIISSCCOONNTTRRAARRYYTTOOIITTSSIINNTTEENNDDEEDD
MMOODDEEOOFFOOPPEERRAATTIIOONN..OOPPEERRAATTIINNGGTTHHEE
RREEMMOOTTEESSTTAARRTTSSYYSSTTEEMMUUNNDDEERRTTHHEESSEECCOONNDDII--
TTIIOONNSSMMAAYYRREESSUULLTTIINNPPRROOPPEERRTTYYDDAAMMAAGGEEOORR
PPEERRSSOONNAALLIINNJJUURRYY..IIMMMMEEDDIIAATTEELLYYCCEEAASSEETTHHEE
UUSSEEOOFFTTHHEEUUNNIITTAANNDDRREEPPAAIIRROORRDDIISSCCOONNNNEECCTT
TTHHEEIINNSSTTAALLLLEEDDRREEMMOOTTEESSTTAARRTTMMOODDUULLEE..
DDIIRREECCTTEEDDWWIILLLLNNOOTTBBEEHHEELLDDRREESSPPOONNSSIIBBLLEEOORR
PPAAYYFFOORRIINNSSTTAALLLLAATTIIOONNOORRRREEIINNSSTTAALLLLAATTIIOONN
CCOOSSTTSS..

8© 2004 Directed Electronics, Inc.
pprriimmaarryyhhaarrnneessss((HH//11)),,
88--ppiinnccoonnnneeccttoorr
rreellaayywwiirreess66--ccoonnnneeccttoorrss
HH11//11
HH11//22
HH11//33
HH11//44
HH11//55
HH11//66
HH11//77
HH11//88
BLUE (-) 200mA Status Output
GRAY (-) Hood Pin Shutdown Input
VIOLET/WHITE Tachometer Input (optional)
BROWN (+) Brake Switch Shutdown Input
BLACK Ground
WHITE/BLUE (-) Remote Start Activation Input
LT. GREEN/BLACK Factory Alarm Disarm
WHITE (-) Parking Light Flash Output (optional)
AA
BB
CC
DD
EE
FF
VIOLET (+) Output to Starter Circuit
PINK (+) Output to IGN1 Circuit
RED (+) (30A) High Current 12V Input
ORANGE (+) Output to ACC1 Circuit
RED (+) (30A) High Current 12V Input
PINK/WHITE(+) Output to IGN2 Circuit

9
© 2004 Directed Electronics, Inc.
uussiinnggLLEEDDtteessttpprroobbee
To use the LED test probe:
1. Remove the protective cover off the probe tip. Save the
protective cover for reinstallation on the probe tip when
the LED tester is not being used.
2. Connect the Black clip to a good chassis ground.
3. Connect the Red clip to a good +12V source. Both the
Red and Green LEDs should be illuminated dimly.
4. If a positive voltage source is probed, the Red LED will
illuminate brightly, and the Green LED will extinguish.
5. If a negative source is probed the Green LED will illu-
minate brightly and the Red LED will extinguish.
Alternate procedure to use the LED test probe (only for use on
probing positive voltage wires):
1. Remove the protective cover off the probe tip. Save the
protective cover for reinstallation on the probe tip when
the LED tester is not being used.
2. Connect the Black clip to a good chassis ground.
3. If a positive voltage source is probed, the Red LED will
illuminate brightly.
note: Do not use this test probe on computerized equip-
ment as damage can result.

10 © 2004 Directed Electronics, Inc.
iinnssttaallllaattiioonn
Be sure to read this section thoroughly and view the Do-It-
Yourself Installation CDROM video in its entirety before
starting the installation. Pay special attention to all warnings to
prevent personal injury or damage to your vehicle.
Visit our 24-hour technical Web site (wwwwww..bbooaasseeccuurriittyy..ccoomm)to
get a vehicle-specific wiring guide prior to starting this installa-
tion. If at any time during the installation you are unable to
answer your questions on the Web site, call 11--880000--887733--11331144for
live technical assistance.
warning! Verify that the vehicle is set to
park and that the parking brake is set
before beginning installation.
warning! On vehicles with air bags or sup-
plemental restraint systems (SRS) you may
notice a bright yellow tube with small wires
in it marked SRS underneath the steering
column near the key cylinder. DO NOT
tamper or unplug these for any reason to
prevent costly damages to your vehicle or
personal injury. Tampering may cause
unintended deployment of airbags.
warning! This system is intended for auto-
matic, fuel-injected vehicles only. Installation
in any other vehicle is contrary to its intend-
ed use.

11
© 2004 Directed Electronics, Inc.
step 1
Ground Wire
The BLACK (H1/5) wire on the main 8-pin harness is ground.
This wire should be connected to a clean, paint-free area of metal
in the drivers kick panel area. First strip back a ¾-inch section of
the insulation off the BLACK wire and crimp a ring terminal
(not provided) to that wire. Locate a clean, paint-free metal
surface in the drivers kick panel. Using a self-tapping screw, drill
the screw with the ring terminal to the metal area. Once screwed
down, pull on the wire to ensure a good connection.
SELF-TAPPING
BOLT OR SCREW
RING
TERMINAL
GROUND
WIRE
NOTE: REMOVE ANY PAINT
BELOW RING CONNECTOR
DIA-591
note: More problems are attributed to poor ground con-
nections than any other cause. Take extra care to ensure
the ground is a clean metal-to-metal contact and secure.
➜

12 © 2004 Directed Electronics, Inc.
step 2
Constant Power and Ignition wires
Almost all power and ignition wires can be found behind the key
cylinder under the lower drivers side dash panel. Using the
appropriate hand tools, remove the lower dash panel using care
not to break any parts. If the panel does not come off easily
check for any additional screws you may have missed.
Once the lower dash panel has been removed, locate the ignition
harness at the back of the key cylinder. This is usually a group of
thicker wires. With the ignition harness exposed, use your LED
tester to find your power and ignition wires.
Place the black lead of the LED tester to a clean metal surface in
the kick panel area and secure it. Probe one of the thicker gauge
wires. The color and identity of your specific vehicle wiring can
be obtained at www.boasecurity.com. With the key in the OFF
position, test the suspect wire. The constant power wire will illu-
minate the LED tester.
➜

13
© 2004 Directed Electronics, Inc.
Once the constant power wire (or wires) has been identified, solder
the two thick RED wires from the control module to it and cover
the connection with electrical tape to ensure a safe connection.
With the black lead still in the kick panel, locate the ignition
wire harness in the same location. It will test differently than
constant (+)12 volts. Locate the suspected wire using the
www.boasecurity.com web site and then use the LED tester to
probe the suspected wire. With the key in the off position the
LED tester will not illuminate. Turn the key to the on position
and the LED tester will illuminate. Now while watching the
LED tester, turn the key to the crank position and the LED
tester should not extinguish. If the LED tester extinguishes this
is not an ignition wire but an accessory wire. If the wire tests
correctly, solder the PINK (C) relay wire to it and cover the
connection with electrical tape.
warning! Before making any connection
to constant battery power make sure that
the two green 30 amp fuses are removed
from the fuse holders on the two thick red
wires. Failure to do so may cause fire or
shorting of sensitive electrical components.

14 © 2004 Directed Electronics, Inc.
If the vehicle requires more than one ignition as per the Web site
information follow the same test procedure and solder the thick
PINK/WHITE (F) relay wire to it and be sure to wrap the
connection with electrical tape. If your vehicle requires more
than two ignitions, contact BOA Technical Support.
step 3
Accessory and Starter wires
The starter and accessory wires will be located in the same harness
as the ignition and constant power.
To find the accessory wire leave the LED tester black lead
connected to the metal ground, take the red lead and probe the
wire suspected to be the accessory. With the key off, your LED
tester should not illuminate. Turn the key to the on position and
the LED tester should be illuminated. Now turn the key to the
crank position. If you have the correct accessory wire the voltage
will disappear while the starter is cranking and return once the key
returns to the on position. If the wire tests correctly, strip the insu-
lation off a small portion and solder the thick ORANGE (C) relay
wire to it and wrap it with electrical tape. If your vehicle requires
more than one accessory contact BOA Technical Support.
➜

15
© 2004 Directed Electronics, Inc.
Now that the accessories have been located, find the wire
suspected to be the starter wire according to the web information
on your vehicle. Place the red lead of your LED tester on the
wire. With the key in the off position the LED tester should be
extinguished in all key positions except the crank position. In
the crank position your LED tester should illuminate, and will
extinguish when the starter disengages.
Once you locate the starter wire, cut the wire in half (cchheecckktthheewweebb
iinnffoorrmmaattiioonnbbeeffoorreeccuuttttiinngg) and try to start the vehicle. If the vehicle
does not start, the correct wire has been identified. Reconnect both
ends of the starter wire while soldering the thick VIOLET (A) relay
wire to it and wrap the connection with electrical tape.
nnoottee::Always check the Web site information on your
vehicle for warnings regarding the starter wire and check
engine lights. Some vehicles will trip a check engine light
if the starter wire is cut.

16 © 2004 Directed Electronics, Inc.
step 4
Safety Shutdown Wires
With all ignition wires properly connected, find the appropriate
safety shutdown wires. These are the brake wire and hood pin wires.
First locate the factory brake wire using your LED tester. Find
the switch at the top of the metal arm coming off the brake
pedal. There are usually two wires connected to that switch.
Locate the wire color according to the web information. With
your black lead still in the kick panel, probe the suspected wire
with the red lead of the LED tester. With the brake pedal at rest
the LED tester should be extinguished. While watching the
tester, depress the brake pedal. The LED tester should illumi-
nate. Once you have located the correct brake wire, strip a small
portion of insulation off this wire and solder the small BROWN
(H1/3) wire on the main harness to it and wrap the connection
with electrical tape.
important! Do not use the vehicle until you confirm the
operation of the brake shutdown.
important! These wires are meant to protect the vehicle
and anyone near the vehicle. They must be connected
appropriately to prevent damage to the vehicle and possi-
ble bodily injury. Failure to properly install these wires may
cause the vehicle to lunge if remote started while in gear.
➜

17
© 2004 Directed Electronics, Inc.
Installing the hood pin switch requires drilling a ¼-inch hole in the
metal lip under the hood. Choose a location that will allow the pin
switch to be depressed when the hood is closed. The pin switch has
a spade connector on the bottom for the wire connection.
Place the wire with the spade connector onto the pin switch and
run the wire into the vehicle’s passenger compartment through a
factory rubber grommet. Using a sharp, pointed object poke a
hole into the grommet and attach the wire to the object with
electrical tape. Pull the wire through the grommet taking extra
care to keep the wire away from any moving parts or anything
that will generate extreme heat. Once the wire is run into the
vehicle and secured from any moving parts, solder the wire to
the GRAY (H1/4) wire on the main wire connector and wrap
the connection with electrical tape.
The bypass toggle switch is designed to bypass the remote start
in an emergency or to disable the remote start functions
important! Do not use the vehicle until you confirm the
operation of the hood pin shutdown.