Directed AS-3472TW User manual

TWO-WAY 6-BUTTON LCD AUTOMATIC/MANUAL
TRANSMISSION REMOTE STARTER
INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment
D1021 2019-05-16 - PGa - Canada
AS-3472TW
User Guide
WARNING
It is the responsibility of the vehicle operator to ensure their vehicle is parked
in a safe and responsible manner.
1. a) Manual transmission: When leaving the vehicle, it is the user’s responsibility
to ensure that the gearshift lever is in the NEUTRAL position and the parking
brake is engaged in order to avoid accidents upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in “Park” in order to avoid
accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled or put
into valet mode before servicing.
A note concerning the battery inside the transmitter:
Depending on your usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the
battery is low, the transmitter will produce two beeps in a repetitive cycle. At that point you should replace
your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy
such as the glove compartment.

P.2User Guide
Table of Contents
Government regulations ...........................................................................................................3
Introduction with SmartStart™ ........................................................................................ 3
Vehicle Presets..........................................................................................................................4
Heater .................................................................................................................................... 4
Windshield Wipers, Radio & Headlights ................................................................................... 4
Using the Transmitter................................................................................................................4
LCD Transmitter basic confirmations....................................................................................... 5
Basic Vehicle Operations ........................................................................................................ 5
Backlight....................................................................................................................................6
Remote’s advanced functions and MENU ................................................................................ 6
How to access default advanced remote functions and MENU.................................................. 6
Remote-Starting Your Vehicle...................................................................................................9
Setting Your Vehicle Into Ready Mode..................................................................................... 9
Remote-starting .................................................................................................................... 10
Driving Off ............................................................................................................................ 10
Arming and disarming the starter kill (if installed) ................................................................. 10
Remote Starter Features ......................................................................................................... 11
Remote Door Locks .............................................................................................................. 11
Remote Trunk Release ......................................................................................................... 11
Idle Mode.............................................................................................................................. 12
Valet Modes.......................................................................................................................... 12
Panic Mode........................................................................................................................... 13
Quick LockoutTM.................................................................................................................... 13
Cold Weather Mode .............................................................................................................. 13
Extended Run Time .............................................................................................................. 14
Disable/Enable LED flashing ................................................................................................. 14
Temperature Request (If ACC-Temp-100 installed)................................................................ 14
Advanced Features: Installation-programmable Options....................................................... 14
Ignition-controlled Door Locks ............................................................................................... 15
Secure Lock.......................................................................................................................... 15
Safe Start ............................................................................................................................. 15
Engine Run Time .................................................................................................................. 15
Turbo Mode .......................................................................................................................... 15
“Home ValetTM” Mode............................................................................................................ 16
AUX 1................................................................................................................................... 16
AUX 2................................................................................................................................... 17
Horn Chirp Timing................................................................................................................. 17
Multi-car Operation................................................................................................................ 17
OEM-Style Alarm .................................................................................................................. 17
Intrusion Codes via horn........................................................................................................ 18
Missing a Start or a Stop Confirmation................................................................................... 18
Multi-Level Features................................................................................................................ 18
Troubleshooting Transmitting Range..................................................................................... 20
Diagnostics – Parking Light Flash Table................................................................................ 20

User Guide P.3
Government regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is
authorized only on a no-interference, no-protection basis; in other words, this device must not be
used if it is determined that it causes harmful interferences to services authorized by IC. In
addition, the user of this device must accept any radio interface that may be received, even if this
interference could affect the operation of the device.
Warning! Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this device.
Introduction with SmartStart™
This is a state-of-the-art remote car starter system. The system is packed with advanced features
such as priority access to the driver’s door (commodity features), the Safe Start children safety
feature and SmartStart™.
SmartStart™ is a groundbreaking technology that enables your remote starter features to be
accessed by your smartphone. Features include keyless entry, trunk release, panic, remote
start/stop toggle and alarm notifications1. Note: SmartStart™ must be professionally installed. For
more information, see your nearest authorised Directed Canada dealer.
With many advanced functions, this product will satisfy any one of your expectations from high-end
commodity and security systems, without neglecting any standard feature commonly offered by
entry-level starters.
1Certain conditions apply. See your authorised Directed Canada dealer.

P.4User Guide
Vehicle Presets
Heater
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the
next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It
is recommended to leave the settings on LOW or MEDIUM instead.
Windshield Wipers, Radio & Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become
energized while running under remote start. When leaving the vehicle you must ensure that the
windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain
types of vehicles could cause them to remain ON even after remote starter shut down, resulting in
a dead battery.
Using the Transmitter
Your remote starter is equipped with a 6-button multi-channel remote control. It can operate two
independent vehicles equipped with identical remote starters (see Multi-car operation section on
page 17).
The functions of the 2-way transmitter are as follows:
LOCK:
Locks the doors and arms the STARTER KILL (if installed).
UNLOCK:
Unlocks the doors and disarms the STARTER KILL (if
installed). Activates the AUX 1 output if Priority Door Access is
configured.
TRUNK:
Opens the TRUNK or activates the AUX 3 output.
Note: Trunk option must be installed.
START:
Remote starts the engine. Gets the system into Cold Weather
mode if pressed for longer than 3 seconds.
Note: Icon may vary.
FUNCTION button
Turns the backlight ON, allows access to the Multi-level
functions and to the Menu.
AUX button (if programmed):
Activates AUX 2
output, stops the engine, requests
Temperature, activates Panic mode or activates Cold Weather
mode.

User Guide P.5
The functions of the 1-way transmitter are as follows (optional):
LOCK:
Locks the doors and arms the
STARTER KILL (if installed).
(Image as reference only)
Model: ASRF1501
FCC: EZSNAH1501
IC: 1513A-NAH1501
Product numbers:
ASRF-1501
GSRF-1501
ASRF-1503
GSRF-1503
UNLOCK:
Unlocks the doors and disarms the
STARTER KILL (if installed). Activates the
AUX 1
output if Priority Door Access is
configured.
TRUNK: Opens the TRUNK or activates the
AUX 3 output.
Note: Trunk option must be installed.
START/STOP:
Remote starts or stops the
engine. Gets the system into Cold Weather
mode by pressing the AUX button and then
pressing and holding the START/STOP button
for 3 seconds. Note: Icon may vary.
AUX
AUX: This button serves as a second function
button.
This button allows assigning different functions
to any of the other four buttons.
LCD Transmitter basic confirmations
Basic Vehicle Operations
Function
Button pressed
Icon / text
Sound
Instructions /description
Lock
/ LOCK
1 beep Lock and arm the system
Unlock
/ UNLOCK
2 beeps Unlock and disarm the system
Trunk or Aux 3
TRUNK
1 beep
Trunk output
Start
0:15 + (default)
3-beeps Start the engine
Stop
None
2-beeps
Stop the engine
Back light On for 5 seconds
Press for 1 sec then release
Cold Weather
mode , then
(default)
1 beep See Cold Weather Mode section
(page-13)
Remote Valet + 1 beep
See Valet mode section
(page-12)
Panic
or for
longer than 5 sec.
None 1 beep
See Panic Mode section
(page-13)

P.6User Guide
Backlight
Three different ways to use the backlight:
•Turning the backlight on for 3 seconds, press the for at least 1 second and
release.
•If the button is pressed and held for more than 5 seconds the backlight will stay ON
as long as the button is held.
•To browse the MENU while the backlight is ON:
a) Press the for at least 1 second and release. The backlight should
turn ON.
b) Within 3 seconds, press the button for 2 seconds to access the
various functions.
Remote’s advanced functions and MENU
How to access default advanced remote functions and MENU
User
Transmitter (default)
1. Press for 1 second and release

Remote beeps once and L-01
appears on screen.
2. Press a 2nd time for 1 second and release 
Remote beeps once and L-02
appears on screen.
3. Press a 3rd time for 1 second and release 
Remote beeps once and L-03
appears on screen.
4. Press a 4th time for 1 second and release 
Remote beeps once and MENU
appears on screen.
5. At that point, press to enter the remote’s
MENU. 
Follow the steps listed below in
“Selecting and adjusting
advance MENU options”:
Note: The order of LEVELS and MENU can be re-arranged in the menu option FBPRO.
Selecting and adjusting advanced menu options:
•When in MENU, press button to enter the menu.
•Press button to move up in the menu or button to move down in the
menu.
•Press button to select the option you would like to adjust
•Press button to increase the value or to activate or deactivate a function
or toggle through the selection.
•Press button to decrease the value or to activate or deactivate a function
or toggle through the selection.
•Press button to move to the next sub-option or go back to the main menu.
•To SAVE modifications and EXIT remote’s MENU, do not touch any button for
approximately 5 to 10 seconds.

User Guide P.7
Remote’s advanced functions and MENU
Display
Description
PARK
(1)
Parking meter countdown
This version of the countdown feature is particularly useful for keeping track of
parking meter time: the user may quickly set up the countdown using the Parking
Menu. The transmitter will beep once, 5min before the Parking countdown reaches 0
and beeps 6 times once the countdown expires.
Through Advanced Options, first press to select MENU, then:
a. Choose PARK and press .
b. Set the time at which you want set the alarm. First set the hour, and
press . Then set the minutes and press .
c. Choose ON and wait. A flashing “P” will appear on screen to
confirm activation.
ALARM
(2)
Alarm Clock
The LCD remote control has a built-in alarm clock, which can be set up using the
Alarm Clock Menu. Once the programmed time is reached, the remote will beep 6
times every minute until a button is pressed.
Through Advanced Options, first press to select MENU, then:
a. Choose ALARM and press .
b. Set the time at which you want to set the alarm. First set the hour,
and press . Then set the minutes and press .
c. Choose ON and wait. A flashing “A” will appear on screen to
confirm activation.
CWM
(3)
Cold weather mode function:
Through Advanced Options, first press to select MENU, then:
a. Choose CWM and press .
b. Choose ON/OFF, then press and hold until icon appears.
VALET
(4)
Valet function:
Through Advanced Options, first press to select MENU, then:
a. Choose VALET and press .
b. Choose ON/OFF, then press and hold until icon appears.
TSTART
(5)
Time start function:
This feature is used to remote start the car at a pre-programmed time. Once the pre-
programmed time is reached, the remote will send a start command to the car
module. (Note: For this feature to work, remote has to be within range of the vehicle).
Through Advanced Options, first press to select MENU, then:
a. Choose TSTART and press .
b. Set the time at which you want to remote start the vehicle. First set
the hour, and press . Then set the minutes and press .
c. Choose ON and wait. A flashing “T” will appear on screen to confirm
activation.
SECUR
(6)
Secure:
This feature is used to lock the keypad of the transmitter to avoid accidental button
press. When the keypad is locked and a button is pressed, the LCD will display
“PRESF” for 1 second and goes back to the clock.
The transmitter keypad can also be locked as follows:
a. Press to select MENU.

P.8User Guide
b. Within 3 seconds, press .
c. The LCD will display “Security” to confirm locking of the keypad.
•
Press for about 1sec, to unlock the transmitter’s keypad.
COLOR
(7)
Backlight color
The backlight can be set to 8 different colors.
Through Advanced Options, first press to select MENU, then:
a. Choose COLOR and press .
b. Choose the desired color by pressing or
LCD
(8)
LCD:
If there is no activity within the programmed time, LCD screen will automatically turn
off after 1 min, 15 min, 30 min, 60 min or always ON. This feature maximizes the
lifetime of the battery.
CLOCK
(9)
Clock:
The Clock menu is used to set the current time on your remote control.
Through Advanced Options, first press to select MENU, then:
a. Choose CLOCK and press .
b. Set the time at which you want to set the clock. First set the hour,
and press , then set the minutes and press .
TEMP
(10)
Temp
Can be set to read the temperature in Celsius (CTEMP) or Fahrenheit (FTEMP)
LANGU
(11)
Language
Can be set to either English or French
SBPRO
(12)
Side button function:
The side button can be programmed as:
•Panic button;
•Stop button;
•Temperature request button;
•Aux 2 output button;
•
or CWM (Cold Weather Mode).
KEYLOC
(13)
Keypad lock
Note: In order for this feature to work, “Secure function” must be set to ON.
If there is no activity within the programmed time, the keypad will automatically lock
after 5 seconds, 10 seconds or 20 seconds.
•
Press for about 1sec, to unlock the transmitter’s keypad.
ILLUM
(14)
LCD illumination:
When this function is enabled, the LCD will illuminate each time LOCK, Unlock or
START is activated.

User Guide P.9
FBPRO
(15)
Button Function:
The order of LEVELS and MENU can be re-arranged using the Button Function
Menu. Details on (page-18).
F Button Function
Menu
FBPRO Function Button Programming
Function Button
programming
1 2 3 M
2 3 1 M
3 1 2 M
2 1 3 M
M 1 2 3
Level 1, level 2, level 3, MENU
Level 2, level 3, level 1, MENU
Level 3, level 1, level 2, MENU
Level 2, level 1, level 3, MENU
MENU, level 1, level 2, Level 3
Remote-Starting Your Vehicle
Setting Your Vehicle Into Ready Mode
If your vehicle has a manual transmission you must read the following indications. The unit must
first be set to Ready Mode in order to start the vehicle by remote. If the unit is not set to Ready
Mode, it cannot remote start the vehicle. Please note that Ready Mode can be enabled by the
remote or the handbrake, depending on the option that was selected by your installer. Therefore,
you must follow the appropriate procedure between the two described below in order to set your
vehicle into Ready Mode.
Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.
The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is
pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON
(RUN) position.
To set the system to Ready Mode:
If Ready Mode is enabled by remote
If Ready Mode is enabled by handbrake
1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the
neutral position.
2. With the engine running, apply the parking
brake once and release the brake pedal.
3. Within 20
sec. of engaging the parking
brake, press and hold , or on the
transmitter (SmartStart™ uses only the
SmartStart™ icon).
The parking lights will flash 3 times quickly
and remain lit. Release the button.
2. With the engine running, apply the parking
brake twice within 10 sec.
3. Make sure to release the brake pedal.
The parking lights will flash 3 times quickly
and remain lit.
4.
Remove the key: the engine will keep on running.
5.
Exit the vehicle. All doors should be closed, including the hood and trunk.
6.
THERE ARE THREE POSSIBLE OPTIONS TO COMPLETE READY MODE (programmable
by installer)
OPTION 1: No lock
OPTION 2: Manual shut down
(default)
OPTION 3: Automatic shut
down
The engine runs for 8 sec.
before finally shutting down
the engine, without user
interaction
The engine keeps going until you
press either;
a. to lock the doors and shut
down the engine;
The engine runs for 8 sec.
then locks the doors before
finally shutting down the
engine, without user

P.10 User Guide
b. to unlock the doors and
shut down the engine;
c. to shut down the engine
without affecting the doors.
interaction.
WARNING:
The vehicle is
not armed or locked down.
WARNING: Engine runs until the
pre-
programmed run time
expires.
WARNING: Do not leave
your keys in the vehicle!
The Parking lights will flash
twice
to indicate Ready
mode is set. To see the
icon, refresh the
remote screen by pressing
The icon will appear on your
screen.
The Parking lights will flash
twice to indicate Ready mode
is set. To see the icon,
refresh the remote screen by
pressing .
Remote-starting
1. Press the button for approximately 1 second and release.
2. The remote will beep once and the LCD will display “START”.
3. The remote will confirm the remote starter’s activation by beeping 3 times.
If your vehicle does not start on the first attempt, the system will shut down, wait a few seconds
and try to start the engine again. There will be 3 start attempts before the system gives up.
Driving Off
With the vehicle running remotely, press the button to disarm the starter kill (if installed) and
unlock the doors. Enter the vehicle and do the following:
1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK
position while the engine is running. This would cause the starter motor to re-engage.)
2. Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.
Note: On some Push-To-Start (PTS) vehicles, no takeover is possible as pressing the brakes will
shut the engine down. Please talk to your technician to determine if the “Takeover mode” can be
set for your vehicle.
Arming and disarming the starter kill (if installed)
This added security feature will prevent the vehicle from starting with the Ignition key when the
starter kill is armed. If the system was installed with the starter kill option, the vehicle will not be
able to start with the key unless the system has been unlocked first or put into Valet Mode
(page 12).
Note: If the Starter Kill is installed, the vehicle will benefit from a protection against starter motor
damage that could occur after remote-starting the engine should the user, by force of habit, turn
the ignition key to the CRANK position.
The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm
automatically) or Active Mode (so as to require the user’s intervention for arming). By default, the
Remote Car Starter is configured to Passive Mode.

User Guide P.11
Passive mode:
To arm the Starter Kill:
•Press the button on the transmitter.
OR
•Let the Starter Kill arm automatically 1 minute (by default) or 3 minutes (if configured this way)
after the ignition is turned OFF or once the last door is closed (if the doors are monitored).
•The LED on the antenna will flash quickly during the countdown preceding the activation
of the Starter Kill.
•Once the activation countdown expires, the LED will send a series of quick double
flashes to indicate that the Starter Kill is now armed.
To disarm the Starter Kill:
•Press the button on the transmitter.
•The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if
configured this way) if no door is left opened (if the doors are monitored) and the ignition
is not turned ON.
Active Mode:
To arm the Starter Kill:
•Press the button on the transmitter.
•The parking lights will flash once.
•The LED on the antenna will flash slowly.
•If remote door locks are installed, this will also lock the doors and arm the OEM-style
alarm (if configured).
To disarm the Starter Kill:
•Press the button on the transmitter.
•The parking lights will flash twice.
•The LED on the antenna will remain OFF.
•If remote door locks are installed, this will also unlock the doors and disarm the OEM-
style alarm (if configured).
Remote Starter Features
Remote Door Locks
If your Remote Car Starter was installed with the Remote Door Locks option, you will have the
convenience of remote keyless entry.
To LOCK your doors and ARM the system:
1. Press and hold the button for approx. 1 sec.
2. The remote will beep once then display the icon to confirm locking of the doors.
To UNLOCK your doors and DISARM the system:
1. Press and hold the button for approx. 1 sec.
2. The remote will beep twice then display the icon to confirm unlocking of the doors.
Remote Trunk Release
If your system was installed with the Remote Trunk Release option, you can open your trunk by
pressing the button until the remote displays the text “TRUNK” on the screen. In addition, this
will also disarm the OEM-style alarm (if installed).

P.12 User Guide
Idle Mode
Convenience feature: Idle Mode allows you to keep the engine running and the doors locked
while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the
Ignition Switch) while the engine is running.
Activating Idle mode (Automatic transmission):
1. With the engine running, make sure to release the brake pedal and press the , or
button on the transmitter until the parking lights come ON.
Note: SmartStart™ can be setup to use the SmartStart™ icon to activate Idle mode.
2. Remove the ignition key from the ignition switch.
The engine will continue running.
3. Exit the vehicle. All doors, the hood and trunk should be closed
4. Press the button to lock the doors, to arm the starter kill and to arm the alarm (if
available). The engine will continue running.
a. When re-entering the vehicle, the user must reinsert the key into the ignition and
turn it to the ON position (not Crank) without pressing on the brake.
b. Once the key is in the ON position, press on the brake pedal to put the
transmission in gear. Pressing the brake pedal at this step will cancel the remote
starter takeover.
c. Drive off.
If your vehicle has a manual transmission, Idle Mode can be activated through the same routine as
that used for Ready Mode (page-9); at the last step, press the button to lock the doors, arm
the system and leave the engine running.
Valet Modes
When the vehicle is in Valet Mode, the remote starter and alarm functionalities are disabled. If the
vehicle needs to be serviced, or if you park it indoors, Valet Mode will prevent the engine from
being remote-started accidentally.
Any of the following features will put the remote car starter into Valet Mode:
Ignition Valet: This feature allows you to set Valet Mode using the ignition key.
Remote valet: This feature allows you to set Valet Mode using the transmitter.
To put the system into Valet Mode
Using the KEY (Ignition Valet Mode):
1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key to the
IGNITION/RUN and OFF positions until parking lights flash 3 times.
2. Turn the ignition OFF.
3. The LED on the antenna will stay ON indicating that the vehicle has successfully entered
Valet mode.
4. The icon will appear on the LCD remote if the or button is pressed.
Using the TRANSMITTER (Remote Valet Mode):
1. Press the and buttons simultaneously until the icon appears on the LCD display.
2. The LED on the antenna will stay ON indicating that the vehicle has successfully entered
Valet mode.

User Guide P.13
To take the system out of Valet Mode
Using the KEY (Ignition Valet Mode):
1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key to the
IGNITION/RUN and OFF positions until parking lights flash twice.
2. Turn the ignition OFF.
3. The LED on the antenna will switch OFF indicating that the vehicle is now out of Valet mode.
4. The icon will disappear from the LCD remote if the or button is pressed.
Using the TRANSMITTER (Remote Valet Mode):
•Press the and buttons simultaneously until the icon disappears from the LCD
display.
•The LED on the antenna will switch OFF indicating that the vehicle is now out of Valet mode.
If someone attempted to remote-start the vehicle while in Valet Mode; the parking lights will turn
ON, then OFF, then will flash twice.
Panic Mode
Note: Panic mode can only be activated if the horn has been adequately configured by the
installer.
In an emergency situation, you can activate panic mode by pressing and holding the OR
button for more than 3 seconds, until the horn starts honking. If the vehicle is under a remote start,
the engine will shutdown automatically before setting off the horn. You can stop the horn by
pressing:
(this will lock your doors and deactivate panic mode),or
(this will unlock your doors and deactivate panic mode).
Furthermore, the panic mode can be stopped by activating Valet Mode (page-12)
* Panic Mode will automatically shut down after 30 sec.
Quick LockoutTM
(Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all
doors when you press the brake pedal while you hear the Horn sounding. (Quick Lockout is only
available when Panic mode has been triggered.)
Cold Weather Mode
If the vehicle has a manual transmission, Ready mode (page-9) should be set before entering
Cold Weather mode. When Cold Weather Mode is active, the engine starts every 2 hours and runs
for 3 minutes (8 or 20 minutes for diesel engines). Cold Weather Mode automatically ends after
24 hours or 12 starts.
To enter Cold Weather Mode:
2-way remote:
1. Press and release to select L-01.
2. Press and hold the button until the icon appears on the display.
OR
1-way remote:
1. Rapidly press AUX twice. While the remote’s LED is flashing, press and hold until the
parking lights flash for 2 seconds, pause, and then flash 3 times.

P.14 User Guide
To exit Cold Weather Mode, do any one of the following actions:
•Open the hood.
•Start the engine remotely.
•Turn the ignition key to the IGNITION ON (RUN) position.
•Or by using the remote as so:
2-way remote
a. Press and release to select L-01.Press and hold the button until the icon
disappears from the display.
1-way remote
b. Rapidly press AUX twice. While the remote’s LED is flashing, press and hold until the
parking lights flash for 2 seconds, pause, and then flash once.
To verify whether the system is in cold weather mode:
•The icon should appear on your remote display.
OR
•(Automatic transmissions only) Press the brake pedal: If the vehicle is in Cold Weather
mode, the parking lights will remain ON while the brake pedal is pressed.
Extended Run Time
While the vehicle is running remotely, press and hold the button until the remote beeps 3 times.
This will reset the run time counter to zero and restart the run time cycle from the beginning.
Note: The extended run time procedure can only be carried out once per remote start.
To stop the vehicle, at any moment, simply press and release the button.
Example: If your remote car starter is programmed for a run time of 3 minutes and your vehicle has
been running for 2 minutes already, pressing the button will reset the counter to zero and allow
the engine to run for another cycle (in this case, 3 minutes).
Disable/Enable LED flashing
To disable the LED: Press and simultaneously until the remote beeps once, pauses for
2 seconds, then beeps once again. Release the buttons. The parking lights will flash 3 times.
To Enable the LED: Press and simultaneously until the remote beeps once, pauses for
2 seconds, then beeps once more. Release the buttons. The parking lights flash once.
Temperature Request (If ACC-Temp-100 installed)
The user can request the temperature in the vehicle if a Temperature Sensor Module (ACC-Temp-
100) is installed:
1. Through the remote’s advanced function menu (page-6), select L-01.
2. Immediately press the button and hold it until the temperature is displayed on the
LCD screen.
Advanced Features: Installation-programmable Options
The remote starter was designed with flexibility and OEM integration in mind. With its program-
mable options, this unit can single-handedly control nearly any electrical system in your vehicle.
Caution: The programming of your system should be left to a professional. Changing any one of
the settings may affect the operation of your remote starter.

User Guide P.15
Ignition-controlled Door Locks
This is an added security feature. If your Remote Car Starter was installed with the Ignition-
Controlled Door Locks option, the doors will automatically lock as soon as the ignition key is turned
to the IGNITION ON (RUN) position while the brakes are pressed. The remote car starter will also
lock any door that was unlocked and opened (then closed) the next time the brake pedal is pressed
(only when doors are monitored). When the key is turned to the OFF position, the doors will
automatically be unlocked.
Secure Lock
Before it can remote-start your vehicle, the remote starter must first disarm the factory security
system. The secure lock feature may be required on certain vehicle models with factory security
systems that automatically unlock the doors when the security system is disarmed. To keep your
vehicle protected when the factory security system is disarmed for a remote start, secure lock will
relock your doors as soon as the vehicle has started. Once the engine run cycle ends, secure lock
will rearm your factory security system.
Safe Start
This feature will eliminate accidental remote starts, e.g. when children are playing with the
transmitter.
Safe start enabled: If this feature is enabled, the user must press the button twice within
3 seconds to remote-start the vehicle.
Swap start: If this feature is enabled;
2-way remote:
1. Through the remote’s advanced function menu (page-6), select L-01.
2. Press to remote start the vehicle.
Note: The AUX 2 output can be activated by pressing the button.
1-way remote:
1. Rapidly press AUX twice. While the remote’s LED is flashing, press to remote start the
vehicle.
Note: The AUX 2 output can be activated by pressing the button.
Engine Run Time
On a gas engine, the Remote Car Starter can be programmed to run the engine for 3, 15, or
25 minutes (15 minutes by default). On a diesel engine, the Remote Car Starter can be
programmed to run the engine for 8, 20, or 30 minutes (20 minutes by default).
Turbo Mode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine.
If your vehicle has an automatic transmission, proceed as follows to set the system to Turbo Mode:
1. With the engine running, make sure to release the brake pedal and press the , or
button on the transmitter until the parking lights come ON.
Note: SmartStart™ can be setup to use the SmartStart™ icon to activate Turbo mode.
2. Remove the ignition key from the ignition switch. The engine will continue running.
3. Exit the vehicle and close all doors, hood and trunk.
4. Press the button; this will lock the doors, arm the OEM-style alarm (if configured) and
confirm that the vehicle is in Turbo Mode.

P.16 User Guide
5. The engine will shut down after 60 seconds.
If your vehicle has a manual transmission, follow all steps of the Ready Mode routine (page-9) to
activate Turbo Mode. At the last step,
•Press to lock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
The OEM-style alarm and starter kill (if configured) will be armed.
•Press to unlock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
•Press to shut down the engine without affecting the doors.
Note: The vehicle will enter Ready Mode once the engine run time expires.
“Home ValetTM” Mode
If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if
the vehicle is parked indoors, there is no danger of it starting accidentally by remote control. If the
vehicle has a manual transmission, it should be set into ready mode before activating the Home
Valet™.
Note: Once the Home Valet™ Mode is activated, the vehicle will not start by remote, but the OEM
alarm functions will remain active.
To put the system into Home Valet™ mode:
1. Press the or button.
2. Within 3 seconds, press the and buttons simultaneously until the transmitter
beep once and display icon on the LCD screen.
To take the system out of Home Valet™ mode:
•Turn the ignition key to the IGNITION ON (RUN) position.
The system will warn you if someone attempts to start your vehicle while it stands in Home Valet™
mode. The parking lights will turn ON then OFF, then flash twice, pause, then flash twice again.
AUX 1
Note: This 500 mA negative Aux 1 output can be used for many different applications
Priority door:
This great feature allows the user to unlock solely the driver’s door with a single press of the
button on the transmitter, and to unlock the other doors, if desired, by pressing the button for a
second time within 5 sec.
The output will provide a 1-second negative output when the button is pressed a second time
on the transmitter.
Horn Confirmation:
AUX 1 can be programmed to trigger the horn every time the button is pressed, or when the
button is pressed twice within 3 seconds. When horn confirmation is activated, panic mode is
enabled. If horn confirmation is disabled, panic mode will not be available.

User Guide P.17
AUX 2
2-way remote: If configured at installation, by default, press the Function button to select level 01
(“L-01”), then press the button to activate AUX 2. Refer to the multi-level features table for
more details.
1-way remote: If configured at installation, press twice quickly on the AUX button, then once on the
button while the LED is slowly flashing.
Horn Chirp Timing
The pulse duration can be configured by your installer (from 5 ms to 200 ms).
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same remote starter model, to
control both systems with a single remote control.
Note: Your remote control must be configured for second car operation by the installer.
To control the second vehicle:
Press + simultaneously:.................................................LOCK
Press + simultaneously:.................................................UNLOCK
Press + simultaneously: ..................................................START
Press + simultaneously: ..................................................STOP
Press :............................................................TRUNK
OR
Press :............................................................LOCK
Press :............................................................UNLOCK
Press : .............................................................START
Press : .............................................................STOP
Press :............................................................TRUNK
OEM-Style Alarm
The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch
of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the
ignition.
•To arm the OEM-style alarm, press the button on the transmitter.
- The OEM-style alarm will ONLY arm if the button on the transmitter is pressed.
- The LED on the antenna will flash slowly to indicate that the OEM-style alarm is now
armed.
•To disarm the OEM-style alarm, press the button on the transmitter.
-To stop the horn from sounding if the OEM-style alarm is triggered, press the
or button, or put the system in and out of Valet Mode (page-12)

P.18 User Guide
Intrusion Codes via horn
The system monitors the following:
•Doors
•Hood
•Ignition
Note: If an intrusion has occurred the HORN will sound for a maximum of 1 minute
If an intrusion has occurred and pressed, the horn provides an intrusion code corresponding to
the type of intrusion that occurred.
Diagnostic table:
1x = power interruption
4x = Doors intrusion
3x = Hood
6x = Ignition
Missing a Start or a Stop Confirmation
If you have not received a Start or the Stop confirmation after pressing the button, pressing the
button within range of the remote starter’s signal will refresh the display and will confirm if the
vehicle was started or stopped.
If no start confirmation was received:
•Press the button:
The remote’s icon will start flashing
The icon and runtime time countdown will be displayed.
If no stop confirmation was received:
•Press the button:
The will be displayed
The remote’s icon and the runtime countdown will disappear.
Multi-Level Features
The multi-level features allow you to access different features of your vehicle or of a second car by
pressing the button once, twice or three times. For convenience purpose, the order of
LEVELS and MENU can be re-arranged through FBPRO setting (page-6)
Features:
•MENU: see page-6 for complete lists of MENU available.
•Basic features: AUX 2, Cold Weather mode, Swap Start, Temperature request
•Multicar Operation: Allows the owner to control both vehicle equipped with the same
remote starter model.
•Customized feature: Your installer can add customized features such as turning on the
radio, opening sliding doors, etc.

User Guide P.19
To control the Multi level features, refer to the tables below:
FBPRO setting 1 *default
FBPRO setting 2
FBPRO
setting Features Levels FBPRO setting Features Levels
1
Basic features
L01
2
Multicar operation
L01
2
Multicar operation
L02
3
Customize feature
L02
3
Customize feature
L03
1
Basic features
L03
M
MENU
MENU
M
MENU
MENU
FBPRO setting 3
FBPRO setting 4
FBPRO
setting Features Levels
FBPRO
setting Features Levels
3
Customize feature
L01
2
Multicar operation
L01
1
Basic features
L02
1
Basic features
L02
2
Multi car operation
L03
3
Customize feature
L03
M
MENU
MENU
M
MENU
MENU
FBPRO setting 5
FBPRO
setting Features Levels
M
MENU
MENU
1
Basic features
L01
2
Multicar operation
L02
3
Customize feature
L03
Example: If the multi-level feature is set to FBPRO setting 3, the basic features can be access as
follow:
To activate AUX 2 feature, browse the remote’s Advance Functions (page-6) and select L02. After
selecting L02, immediately press lock to activate AUX 2 feature.

P.20 User Guide
Troubleshooting Transmitting Range
Many factors may affect the operating range of the transmitter. Some of these are:
•The condition of the battery in the transmitter.
•The operating environment (for example: downtown radio-frequency noise, airports, cellular
phone towers…)
•Metal: any type of metal will affect operating range. This includes the metal in the car.
•The shape of the vehicle can affect range as well; vans in general have an especially poor
range.
•The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in this
case the signal from the remote control). As a result, the direction in which the vehicle is facing
in relation to the remote control can affect the range. Straight on – standing in front of the
vehicle – generally gives you the greatest range; the second best performance is from the back.
Using the remote control from either side of the vehicle will usually give the lowest range.
•The range will be significantly lower in a crowded parking lot than in open space.
•Always hold the transmitter high, approximately at shoulder height. Holding the transmitter
against your chin will also increase your range: your head acts as an antenna.
•The operating range will be somewhat lower on vehicles equipped with an aftermarket or factory
alarm.
Diagnostics – Parking Light Flash Table
Parking lights flashes
Description
1
•Doors locked.
•Trunk released.
•Start signal received from the remote.
•Runtime has expired
2 slow
•Shutdown by remote
2 fast
•Doors unlocked
•Valet mode is deactivated
3 slow
•Runtime is extended.
3 fast
•Valet mode activated.
4 fast
•Shutdown by brake
•A remote start was attempted while the brake pedal is engaged.
10 fast
•Shutdown by hood
•A remote start was attempted while the hood is open.
ON twice
•Cold weather mode deactivated
ON 3 times
•Cold weather mode activated.
Solid ON
•Engine is running under remote start.
Flash for 30 sec.
•Panic mode is triggered.
Flash for 60 sec.
•Alarm is triggered.
ON twice twice
•A remote start was attempted while the system is in home valet.