Directed DS4+ User manual

Designed by Installers for Installers
INSTALLATION GUIDE
DS4+
2010 Toyota Camry (Smart Key). 933.TL1 5.03.185
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.

Introduction 4
Vehicle function compatibilities 4
Pre-installation and application warnings 5
OEM remote starter detection 6
Wiring diagram 7
Locating components in the vehicle 8
Vehicle connections 9
Connecting the module 12
Important! 12
RF Systems 12
8556T Temperature Sensor 12
8504D Combo Sensor 12
When used in conjunction with SmartStart 12
D2D port configuration 13
Module programming 14
LED diagnostics and troubleshooting 15
Soft reset 17
Hard reset 17
Learning the Tach (not needed with Virtual Tach) 18
Initializing Virtual Tach (not needed with hardwired or data tach applications) 18
Limited lifetime consumer warranty 19
Quick reference guide 20
Contents

3933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.

4933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Introduction
DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features
built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information
on the installation of the module as an analog unit, however a digital solution could be available for your
vehicle. Please refer to the DirectLink application or www.directechs.com for more information about which
configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also
be configured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the
Google Play or Apple store.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
Accessory Activation
Ignition Activation
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
E-Brake Status
Ignition Status

5933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming 1Keys required for operation 0
No takeover feature is available on Push-to-Start vehicles. The vehicle will shut down as soon as a door is opened.
To remote start the engine, the hood, hatch, and all doors MUST be closed.
Keyless and Smart Key will remain functional during remote start.
All connectors are displayed from the wire side (unless specified otherwise).
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each
wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] Autolights Interrupt ONLY required if vehicles are equipped with Autolights.
[4] Connection required ONLY if Pit Stop/Idle mode is desired.

6933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
OEM remote starter detection
How to know if the vehicle is equipped with an OEM remote starter
1. An “ENGINE STARTER”
sticker should be on the remote.
ENGI NE
STARTER
2. Remote start the OEM remote starter:
Press the remote control’s lock button twice within 2 seconds, then press and hold the lock
button for 3 seconds.
x2 &Press & Hold
for 3 seconds
The parking lights flash after 3 seconds. The engine starts and the parking lights flash
repeatedly for 20 seconds.
If the vehicle is equipped with an add-on Lexus/Toyota OEM remote starter
The factory remote starter must be permanently disconnected before programming the Directed interface as both modules cannot
coexist. See "Locating the OEM Remote Starter" below.
Locating the OEM Remote Starter
Vehicle OEM Remote Starter & Connector Location
Toyota Camry (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel.
Toyota Camry Hybrid (Smart Key) 2007-2011 Behind Glove Box & Passenger kick panel.
Toyota Corolla (Smart Key) 2009-2013 Behind Glove Box & Passenger kick panel & Junction Box & Steering column.
Toyota Highlander (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel.
Toyota Highlander Hybrid (Smart Key) 2008-2013 Behind Glove Box & Passenger kick panel.
Toyota Rav4 (Smart Key) 2009-2012 Behind Glove Box & Junction Box.

7933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
(+) 12V Input: Blue/Red: 2
(-) Ground: Black: 10
HS CAN Low: Tan: 1
(-) Parking Light Output: Lt.Green/Black: 1
(-) Push-to-Start Output: Lt.Blue/Black: 10
HS CAN High: Tan/Black: 2
Siren
Hood Pin
(+) 12V Input: Red: 6 &12
Autolights Interrupt (veh. side): Lt.Green: 8
Autolights Interrupt (conn. side): Lt.Green/White: 9
(+) Start Stop Switch Output: Blue: 3
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
OBDII
Diagnostic
Connector
(-) Parking Lights:
Black or Lt. Blue, pin 18
(+) 12V,
Black or White,
pin 1
1
(+) STSW: Pin 4 or 6
16
8
9
1
12345678910
1112131415161720
18
1543 1
811
12 10 9
14
6
13
2
ENGINE
START
STOP 7
(-) Push-To-Start:
Blue or Pink, pin 7
PTS Switch
(black conn.
behind PTS button)
Headlight Switch
(white conn.
at headlight switch)
Main Body ECU
(white conn.
under drivers dash)
Dash Fuse Box
(white conn.)
Autolight:
Green or Yellow, pin 19
19
CUT
HS CAN Low: Pin 14
HS CAN High: Pin 6
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
It is important to check that the
fuses are positioned correctly.
10 9 8
6543
7
2 1
OR
Wiring diagram

8933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Locating components in the vehicle

9933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2010 Toyota Camry (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Main harness, 12-pin black connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.
H1/1 Blue/White Relay N.C. No Connection No Connection
H1/2 Blue/Red Relay N.O. STSW Body ECU on back of dash fuse box, white 10 pin plug, pin 4 + gray
H1/3 Blue Relay COM STSW dash fuse box, white 1 pin plug (A), pin 1 + black (120A)
H1/4 White/Brown Relay N.C. No Connection No Connection
H1/5 White Relay COM Clutch Activation Output clutch switch, black 2 pin plug, pins 1 and 2 +
N.O. red (in), green (out)
H1/6 Red No Connection No Connection
H1/7 Lt. Green/Red Relay N.O. No Connection No Connection
H1/8 Lt. Green Relay COM Auto Light headlight switch, white 20 pin plug, pin 19 cut green
H1/9 Lt. Green/White Relay N.C. Auto Light headlight switch, white 20 pin plug, pin 19 cut green
H1/10 Black No Connection No Connection
H1/11 White Relay COM No Connection No Connection
H1/12 Red No Connection No Connection
Relay harness, 10-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.
H2/1 N/A No Connection No Connection
H2/2 Red/Black No Connection No Connection
H2/3 Pink/Black No Connection No Connection
H2/4 Pink/White No Connection No Connection
H2/5 Red No Connection No Connection
H2/6 Green No Connection No Connection
H2/7 Violet No Connection No Connection
H2/8 Orange No Connection No Connection
H2/9 Red/White No Connection No Connection
H2/10 Pink No Connection No Connection
Data harness, 8-pin white connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.
H3/1 Tan (Data) HS CAN Low data link connector, black 16 pin plug, pin 14 data white
H3/2 Tan/Black (Data) HS CAN High data link connector, black 16 pin plug, pin 6 data black
H3/3 Orange/Brown No Connection No Connection
H3/4 Orange/Green No Connection No Connection

10 933.TL1 5.03.185 2010 Toyota Camry (Smart Key)
© 2017-10-17 Directed. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.
H3/5 Lt. Green No Connection No Connection
H3/6 Violet/Brown No Connection No Connection
H3/7 Orange/Black No Connection No Connection
H3/8 Yellow/Black No Connection No Connection
Analog input/output harness, 22-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.
H4/1 Lt. Green/Black (-) Pk Light Output headlight switch, white 20 pin plug, pin 18 - black
H4/2 Blue/White No Connection No Connection
H4/3 Dk. Green/Black No Connection No Connection
H4/4 Red/White No Connection No Connection
H4/5 Brown/Black No Connection No Connection
H4/6 Brown/White No Connection No Connection
H4/7 White (+) No Connection No Connection
H4/8 Violet/Black No Connection No Connection
H4/9 Dk. Blue/Black No Connection No Connection
H4/10 Lt. Blue/Black (-) PTS engine start stop switch, black or gray 14 pin plug, pin 7 - blue
H4/11 Brown/Red No Connection No Connection
H4/12 Pink No Connection No Connection
H4/13 Violet No Connection No Connection
H4/14 Brown No Connection No Connection
H4/15 White/Blue No Connection No Connection
H4/16 Red/Blue No Connection No Connection
H4/17 Black/White No Connection No Connection
H4/18 Orange/Black No Connection No Connection
H4/19 Blue No Connection No Connection
H4/20 Green No Connection No Connection
H4/21 Gray (-) Hood Switch Input
H4/22 Violet/White No Connection No Connection