DirekTronik LT-22222-L User manual

LT-22222-L LoRa IO Controller User Manual
last modified by Xiaoling
on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
Table of Contents
1.Introduction ........................................................................................................................................................................... 5
1.1 What is LT Series I/O Controller ................................................................................................................................. 5
1.2 Specifications ................................................................................................................................................................ 5
1.3Features .......................................................................................................................................................................... 6
1.4 Applications ................................................................................................................................................................... 6
1.5Hardware Variants ......................................................................................................................................................... 7
2.Power ON Device ............................................................................................................................................................... 7
3.Operation Mode .................................................................................................................................................................. 7
3.1How it works? ................................................................................................................................................................ 7
3.2 Example to join LoRaWAN network ........................................................................................................................... 8
3.3Uplink Payload ............................................................................................................................................................. 10
3.3.1AT+MOD=1, 2ACI+2AVI ...................................................................................................................................... 10
3.3.2 AT+MOD=2, (Double DI Counting) ..................................................................................................................... 11
3.3.3 AT+MOD=3, Single DI Counting + 2 x ACI ....................................................................................................... 12
3.3.4 AT+MOD=4, Single DI Counting + 1 x Voltage Counting ................................................................................ 13
3.3.5 AT+MOD=5, Single DI Counting + 2 x AVI + 1 x ACI ...................................................................................... 14
3.3.6 AT+ADDMOD=6. (Trigger Mode, Optional) ...................................................................................................... 14
3.3.7 Payload Decoder ................................................................................................................................................... 16
3.4 Configure LT via AT or Downlink .............................................................................................................................. 16
3.4.1 Common Commands ............................................................................................................................................ 16
3.4.2 Sensor related commands ................................................................................................................................... 17
3.5 Integrate with Mydevice ............................................................................................................................................. 26
3.6 Interface Detail ............................................................................................................................................................ 30
3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active ) ........................................................................ 30
3.6.2 Digital Input Port: DI1/DI2 ( For LT-22222-L) .................................................................................................... 31
3.6.3 Digital Output Port: DO1/DO2 /DO3 ................................................................................................................... 32
3.6.4 Analog Input Interface .......................................................................................................................................... 32
3.6.5 Relay Output .......................................................................................................................................................... 33
3.7 LEDs Indicators ........................................................................................................................................................... 34
4. Use AT Command ........................................................................................................................................................... 35
4.1 Access AT Command ................................................................................................................................................ 35
4.2 Common AT Command Sequence ........................................................................................................................... 37
4.2.1 Multi-channel ABP mode (Use with SX1301/LG308) ....................................................................................... 37
4.2.2 Single-channel ABP mode (Use with LG01/LG02) ........................................................................................... 38
4.2.3 Change to Class A ................................................................................................................................................ 39
5. FAQ .................................................................................................................................................................................... 39
5.1 How to upgrade the image? ...................................................................................................................................... 39
5.4 Can I see counting event in Serial? .......................................................................................................................... 43
7. Order Info .......................................................................................................................................................................... 45
8. Packing Info ...................................................................................................................................................................... 45
9. Support .............................................................................................................................................................................. 46
10. Reference ........................................................................................................................................................................ 46
Page 2 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
Table of Contents:
•1.Introduction
•1.1 What is LT Series I/O Controller
•1.2 Specifications
•1.3Features
•1.4 Applications
•1.5Hardware Variants
•2.Power ON Device
Page 3 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
•3.Operation Mode
•3.1How it works?
•3.2 Example to join LoRaWAN network
•3.3Uplink Payload
•3.3.1AT+MOD=1, 2ACI+2AVI
•3.3.2 AT+MOD=2, (Double DI Counting)
•3.3.3 AT+MOD=3, Single DI Counting + 2 x ACI
•3.3.4 AT+MOD=4, Single DI Counting + 1 x Voltage Counting
•3.3.5 AT+MOD=5, Single DI Counting + 2 x AVI + 1 x ACI
•3.3.6 AT+ADDMOD=6. (Trigger Mode, Optional)
•3.3.7 Payload Decoder
•3.4 Configure LT via AT or Downlink
•3.4.1 Common Commands
•3.4.2 Sensor related commands
•3.4.2.1 Set Transmit Interval
•3.4.2.2 Set Work Mode (AT+MOD)
•3.4.2.3 Poll an uplink
•3.4.2.4 Enable Trigger Mode
•3.4.2.5 Poll trigger settings
•3.4.2.6 Enable / Disable DI1/DI2/DI3 as trigger
•3.4.2.7 Trigger1 – Set DI1 or DI3 as trigger
•3.4.2.8 Trigger2 – Set DI2 as trigger
•3.4.2.9 Trigger – Set AC (current) as trigger
•3.4.2.10 Trigger – Set AV (voltage) as trigger
•3.4.2.11 Trigger – Set minimum interval
•3.4.2.12 DO -- Control Digital Output DO1/DO2/DO3
•3.4.2.13 DO -- Control Digital Output DO1/DO2/DO3 with time control
•3.4.2. 14 Relay -- Control Relay Output RO1/RO2
•3.4.2.15 Relay -- Control Relay Output RO1/RO2 with time control
•3.4.2.16 Counting -- Voltage threshold counting
•3.4.2.17 Counting -- Pre-configure the Count Number
•3.4.2.18 Counting -- Clear Counting
•3.4.2.19 Counting -- Change counting mode save time
•3.4.2.20Reset save RO DO state
•3.4.2.21Encrypted payload
•3.4.2.22Get sensor value
•3.4.2.23 Resets the downlink packet count
•3.4.2.24 When the limit bytes are exceeded, upload in batches
•3.4.2.25Copy downlink to uplink
•3.4.2.26 Query version number and frequency band 、TDC
•3.5 Integrate with Mydevice
•3.6 Interface Detail
•3.6.1 Digital Input Port: DI1/DI2 /DI3 ( For LT-33222-L, low active )
•3.6.2 Digital Input Port: DI1/DI2 ( For LT-22222-L)
•3.6.3 Digital Output Port: DO1/DO2 /DO3
•3.6.4 Analog Input Interface
•3.6.5 Relay Output
•3.7 LEDs Indicators
•4. Use AT Command
•4.1 Access AT Command
•4.2 Common AT Command Sequence
•4.2.1 Multi-channel ABP mode (Use with SX1301/LG308)
•4.2.2 Single-channel ABP mode (Use with LG01/LG02)
•4.2.3 Change to Class A
•5. FAQ
•5.1 How to upgrade the image?
•5.2 How to change the LoRa Frequency Bands/Region?
•5.3 How to set up LT to work with Single Channel Gateway such as LG01/LG02?
•5.4 Can I see counting event in Serial?
•5.5 Can i use point to point communication for LT-22222-L?
Page 4 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
•5.6Why does the relay output become the default and open relay after the lt22222 is powered off?
•5.7 Can i set up LT-22222-L as a NC(Normal Close) Relay?
•5.8Can LT22222-L save RO state?
•6. Trouble Shooting
•6.1 Downlink doesn't work, how to solve it?
•6.2 Have trouble to upload image.
•6.3 Why I can't join TTN in US915 /AU915 bands?
•7. Order Info
•8. Packing Info
•9. Support
•10. Reference
1.Introduction
1.1 What is LT Series I/O Controller

The DraginoLT series I/O Modules are Long Range LoRaWAN I/O Controller. It contains different I/O Interfaces
such as:analog current Input, analog voltage input, relay output, digital input and digital output etc. The
LT I/O Modules are designed to simplify the installation of I/O monitoring.
The LT I/O Controllers allows the user to send data and reach extremely long ranges. It provides ultra-long
range spread spectrum communication and high interference immunity whilst minimizing current consumption. It
targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities,
smartphone detection, building automation, and so on.
The LT I/O Controllers is aiming to provide aneasy and low cost installationby using LoRa wireless technology.
The use environment includes:
1) If user's area has LoRaWAN service coverage, they can just install the I/O controller and configure it to connect
the LoRaWAN provider via wireless.
2) User can set up a LoRaWAN gateway locally and configure the controller to connect to the gateway via wireless.


1.2 Specifications

Hardware System:
• STM32L072xxxx MCU
• SX1276/78 Wireless Chip
Page 5 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
• Power Consumption:
• Idle: 4mA@12v
• 20dB Transmit: 34mA@12v

Interface for Model: LT22222-L:
• 2 x Digital dual direction Input (Detect High/Low signal, Max: 50v, or 220v with optional external resistor)
• 2 x Digital Output (NPN output. Max pull up voltage 36V,450mA)
• 2 x Relay Output (5A@250VAC / 30VDC)
• 2 x 0~20mA Analog Input (res:0.01mA)
• 2 x 0~30V Analog Input (res:0.01v)
• Power Input 7~ 24V DC.

LoRa Spec:
• Frequency Range:
• Band 1 (HF): 862 ~ 1020 Mhz
• Band 2 (LF): 410 ~ 528 Mhz
• 168 dB maximum link budget.
• +20 dBm - 100 mW constant RF output vs.
• +14 dBm high efficiency PA.
• Programmable bit rate up to 300 kbps.
• High sensitivity: down to -148 dBm.
• Bullet-proof front end: IIP3 = -12.5 dBm.
• Excellent blocking immunity.
• Low RX current of 10.3 mA, 200 nA register retention.
• Fully integrated synthesizer with a resolution of 61 Hz.
• FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
• Built-in bit synchronizer for clock recovery.
• Preamble detection.
• 127 dB Dynamic Range RSSI.
• Automatic RF Sense and CAD with ultra-fast AFC.
• Packet engine up to 256 bytes with CRC.

1.3Features
• LoRaWAN Class A & Class C protocol
• Optional Customized LoRa Protocol
• Frequency Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/RU864/IN865/MA869
• AT Commands to change parameters
• Remote configure parameters via LoRa Downlink
• Firmware upgradable via program port
• Counting
1.4 Applications
• Smart Buildings & Home Automation
• Logistics and Supply Chain Management
• Smart Metering
• Smart Agriculture
• Smart Cities
• Smart Factory
Page 6 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
1.5Hardware Variants
Model Photo Description
LT22222-L • 2 x Digital Input (Bi-direction)
• 2 x Digital Output
• 2 x Relay Output (5A@250VAC / 30VDC)
• 2 x 0~20mA Analog Input (res:0.01mA)
• 2 x 0~30V Analog Input (res:0.01v)
• 1 x Counting Port
2.Power ON Device
The LT controller can be powered by 7 ~ 24V DC power source. Connect VIN to Power Input V+ and GND to power
input V- to power the LT controller.
PWR will on when device is properly powered.

3.Operation Mode
3.1How it works?
The LT is configured as LoRaWAN OTAA Class C mode by default. It has OTAA keys to join network. To connect
a local LoRaWAN network, user just need to input the OTAA keys in the network server and power on the LT. It will
auto join the network via OTAA. For LT-22222-L, the LED will show the Join status: After power on TX LED will fast
blink 5 times, LT-22222-L will enter working mode and start to JOIN LoRaWAN network. TX LED will be on for 5
seconds after joined in network. When there is message from server, the RX LED will be on for 1 second.
Page 7 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
In case user can't set the OTAA keys in the network server and has to use the existing keys from server. User can
use AT Command to set the keys in the devices.
3.2 Example to join LoRaWAN network
This chapter shows an example for how to join the TTN LoRaWAN Network. Below is the network structure, we use
our LG308 as LoRaWAN gateway here.

The LG308 is already set to connect to TTN network. So what we need to do now is only configure register this
device to TTN:

Step 1: Create a device in TTN with the OTAA keys from LT IO controller.
Each LT is shipped with a sticker with the default device EUI as below:
Input these keys in the LoRaWAN Server portal. Below is TTN screen shot:
Add APP EUI in the application.
Page 8 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
Add APP KEY and DEV EUI
Step 2: Power on LT and it will auto join to the TTN network. After join success, it will start to upload message to
TTN and user can see in the panel.

Page 9 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
3.3Uplink Payload
There are five working modes + one interrupt mode on LT for different type application:
•MOD1: (default setting): 2 x ACI + 2AVI + DI + DO + RO
•MOD2: Double DI Counting + DO + RO
•MOD3: Single DI Counting + 2 x ACI + DO + RO
•MOD4: Single DI Counting + 1 x Voltage Counting + DO + RO
•MOD5: Single DI Counting + 2 x AVI + 1 x ACI + DO + RO
•ADDMOD6: Trigger Mode, Optional, used together with MOD1 ~ MOD5
3.3.1AT+MOD=1, 2ACI+2AVI
The uplink payload includes totally 9 bytes. Uplink packets use FPORT=2 and every 10 minutes send one uplink by
default.

DIDORO is a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
Page 10 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
• RO is for relay. ROx=1 : close，ROx=0 always open.
• DI is for digital input. DIx=1: high or float, DIx=0: low.
• DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
Note: DI3 and DO3 bit are not valid for LT-22222-L
For example if payload is:
The value for the interface is:
AVI1 channel voltage is 0x04AB/1000=1195（DEC）/1000=1.195V
AVI2 channel voltage is 0x04AC/1000=1.196V
ACI1 channel current is 0x1310/1000=4.880mA
ACI2 channel current is 0x1300/1000=4.864mA
The last byte 0xAA= 10101010(B) means
• [1] RO1 relay channel is close and the RO1 LED is ON.
• [0] RO2 relay channel is open and RO2 LED is OFF;
LT22222-L:
• [1] DI2 channel is high input and DI2 LED is ON;
• [0] DI1 channel is low input;
• [0] DO3 channel output state
• DO3 is float in case no load between DO3 and V+.;
• DO3 is high in case there is load between DO3 and V+.
• DO3 LED is off in both case
• [1] DO2 channel output is low and DO2 LED is ON.
• [0] DO1 channel output state
• DO1 is float in case no load between DO1 and V+.;
• DO1 is high in case there is load between DO1 and V+.
• DO1 LED is off in both case
3.3.2 AT+MOD=2, (Double DI Counting)
For LT-22222-L: this mode the DI1 and DI2 are used as counting pins.
Total : 11 bytes payload
DIDOROis a combination for RO1, RO2, DO3, DO2 and DO1. Totally 1bytes as below
Page 11 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
• RO is for relay. ROx=1 : close，ROx=0 always open.
• FIRST: Indicate this is the first packet after join network.
• DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
Note: DO3 bit is not valid for LT-22222-L.

To use counting mode, please run:
AT+MOD=2
ATZ

AT Commands for counting:

For LT22222-L:
AT+TRIG1=0,100 (set DI1 port to trigger on low level, valid signal is 100ms)
AT+TRIG1=1,100 (set DI1 port to trigger on high level, valid signal is 100ms )
AT+TRIG2=0,100 (set DI2 port to trigger on low level, valid signal is 100ms)
AT+TRIG2=1,100 (set DI2 port to trigger on high level, valid signal is 100ms )
AT+SETCNT=1,60 (Set COUNT1 value to 60)
AT+SETCNT=2,60 (Set COUNT2 value to 60)
3.3.3 AT+MOD=3, Single DI Counting + 2 x ACI
LT22222-L: This mode the DI1 is used as a counting pin.

DIDOROis a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
• RO is for relay. ROx=1 : close，ROx=0 always open.
Page 12 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
• FIRST: Indicate this is the first packet after join network.
• DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
Note: DO3 is not valid for LT-22222-L.
To use counting mode, please run:
AT+MOD=3
ATZ
Other AT Commands for counting are similar to MOD2 Counting Command.
3.3.4 AT+MOD=4, Single DI Counting + 1 x Voltage Counting
LT22222-L: This mode the DI1 is used as a counting pin.
The AVI1 is also used for counting. AVI1 is used to monitor the voltage. It will check the voltage every 60s, if
voltage is higher or lower than VOLMAX mV, the AVI1 Counting increase 1, so AVI1 counting can be used to
measure a machine working hour.
DIDOROis a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
• RO is for relay. ROx=1 : close，ROx=0 always open.
• FIRST: Indicate this is the first packet after join network.
• DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
Note: DO3 is not valid for LT-22222-L.

To use this mode, please run:
AT+MOD=4
ATZ
Other AT Commands for counting are similar to MOD2 Counting Command.

Plus below command for AVI1 Counting:
AT+SETCNT=3,60 (set AVI Count to 60)
AT+VOLMAX=20000 (If AVI1 voltage higher than VOLMAX (20000mV =20v), counter increase 1)
AT+VOLMAX=20000,0 (If AVI1 voltage lower than VOLMAX (20000mV =20v), counter increase 1)
AT+VOLMAX=20000,1 (If AVI1 voltage higer than VOLMAX (20000mV =20v), counter increase 1)
Page 13 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
3.3.5 AT+MOD=5, Single DI Counting + 2 x AVI + 1 x ACI
LT22222-L: This mode the DI1 is used as a counting pin.

DIDOROis a combination for RO1, RO2, DI3, DI2, DI1, DO3, DO2 and DO1. Totally 1bytes as below
• RO is for relay. ROx=1 : close，ROx=0 always open.
• FIRST: Indicate this is the first packet after join network.
• DO is for reverse digital output. DOx=1: output low, DOx=0: high or float.
Note: DO3 is not valid for LT-22222-L.

To use this mode, please run:
AT+MOD=5
ATZ
Other AT Commands for counting are similar to MOD2 Counting Command.
3.3.6 AT+ADDMOD=6. (Trigger Mode, Optional)
This mode is an optional mode for trigger purpose. It can run together with other mode.
For example, if user has configured below commands:
•AT+MOD=1 --> The normal working mode
•AT+ADDMOD6=1--> Enable trigger
LT will keep monitoring AV1/AV2/AC1/AC2 every 5 seconds; LT will send uplink packets in two cases:
1. Periodically uplink (Base on TDC time). Payload is same as the normal MOD (MOD 1 for above command).
This uplink uses LoRaWAN unconfirmed data type
2. Trigger uplink when meet the trigger condition. LT will sent two packets in this case, the first uplink use
payload specify in this mod (mod=6), the second packets use the normal mod payload(MOD=1 for above
settings). Both Uplinks use LoRaWAN CONFIRMED data type.
AT Command to set Trigger Condition:
Trigger base on voltage:
Format: AT+AVLIM=<AV1_LIMIT_LOW>,< AV1_LIMIT_HIGH>,<AV2_LIMIT_LOW>,< AV2_LIMIT_HIGH>
Example:
AT+AVLIM=3000,6000,0,2000 (If AVI1 voltage lower than 3v or higher than 6v. or AV2 voltage is higher than
2v, LT will trigger Uplink)
AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
Trigger base on current:
Format: AT+ACLIM=<AC1_LIMIT_LOW>,< AC1_LIMIT_HIGH>,<AC2_LIMIT_LOW>,< AC2_LIMIT_HIGH>
Page 14 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
Example:
AT+ACLIM=10000,15000,0,0 (If ACI1 voltage lower than 10mA or higher than 15mA, trigger an uplink)
Trigger base on DI status:
DI status trigger Flag.
Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
Example:
AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)
Downlink Command to set Trigger Condition:
Type Code: 0xAA. Downlink command same as AT Command AT+AVLIM, AT+ACLIM
Format: AA xx yy1 yy1 yy2 yy2 yy3 yy3 yy4 yy4
AA: Code for this downlink Command:
xx: 0: Limit for AV1 and AV2; 1: limit for AC1 and AC2 ; 2 DI1, DI2 trigger enable/disable
yy1 yy1: AC1 or AV1 low limit or DI1/DI2 trigger status.
yy2 yy2: AC1 or AV1 high limit.
yy3 yy3: AC2 or AV2 low limit.
Yy4 yy4: AC2 or AV2 high limit.
Example1: AA 00 13 88 00 00 00 00 00 00
Same as AT+AVLIM=5000,0,0,0 (If AVI1 voltage lower than 5V , trigger uplink, 0 means ignore)
Example2: AA 02 01 00
Same as AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)
Trigger Settings Payload Explanation:
MOD6 Payload : total 11 bytes payload
TRI FLAG1 is a combination to show if trigger is set for this part. Totally 1byte as below
• Each bits shows if the corresponding trigger has been configured.
Example:
10100000: Means the system has configure to use the trigger: AC1_LOW and AV2_LOW
Page 15 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
TRI Status1 is a combination to show which condition is trigger. Totally 1byte as below
• Each bits shows which status has been trigger on this uplink.
Example:
10000000: Means this packet is trigger by AC1_LOW. Means voltage too low.
TRI_DI FLAG+STAis a combination to show which condition is trigger. Totally 1byte as below
• Each bits shows which status has been trigger on this uplink.
Example:
00000111: Means both DI1 and DI2 trigger are enabled and this packet is trigger by DI1.
00000101: Means both DI1 and DI2 trigger are enabled.
Enable/Disable MOD6: 0x01: MOD6 is enable. 0x00: MOD6 is disable.
Downlink command to poll MOD6 status:
AB 06
When device got this command, it will send the MOD6 payload.
3.3.7 Payload Decoder

Decoder for TTN/loraserver/ChirpStack: https://github.com/dragino/dragino-end-node-decoder
3.4 Configure LT via AT or Downlink
User can configure LT I/O Controller via AT Commandsor LoRaWAN Downlink Commands
There are two kinds of Commands:
•Common Commands: They should be available for each sensor, such as: change uplink interval, reset
device. For firmware v1.5.4, user can find what common commands it supports: End Device AT Commands
and Downlink Command
•Sensor Related Commands: These commands are special designed for LT-22222-L. User can see these
commands below:
3.4.1 Common Commands
They should be available for each of Dragino Sensors, such as: change uplink interval, reset device. For firmware
v1.5.4, user can find what common commands it supports:End Device AT Commands and Downlink Command
Page 16 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
3.4.2 Sensor related commands
3.4.2.1 Set Transmit Interval
Set device uplink interval.
•AT Command:
AT+TDC=N
Example:AT+TDC=30000. Means set interval to 30 seconds
•Downlink Payload (prefix 0x01):
0x01 aa bb cc// Same as AT+TDC=0x(aa bb cc)
3.4.2.2 Set Work Mode (AT+MOD)
Set work mode.
•AT Command:
AT+MOD=N
Example: AT+MOD=2. Set work mode to Double DI counting mode
•Downlink Payload (prefix 0x0A):
0x0A aa // Same as AT+MOD=aa
3.4.2.3 Poll an uplink
•AT Command:
There is no AT Command to poll uplink
•Downlink Payload (prefix 0x08):
0x08 FF// Poll an uplink
Example: 0x08FF, ask device to send an Uplink
3.4.2.4 Enable Trigger Mode
Use of trigger mode, please check ADDMOD6
•AT Command:
AT+ADDMOD6=1 or 0
1:Enable Trigger Mode
0:Disable Trigger Mode
•Downlink Payload (prefix 0x0A 06):
0x0A 06 aa // Same as AT+ADDMOD6=aa
3.4.2.5 Poll trigger settings
Poll trigger settings,
Page 17 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
•AT Command:
There is no AT Command for this feature.
•Downlink Payload (prefix 0x AB 06):
0xAB 06 // Poll trigger settings, device will uplink trigger settings once receive this command
3.4.2.6 Enable / Disable DI1/DI2/DI3 as trigger
Enable Disable DI1/DI2/DI2 as trigger,
•AT Command:
Format: AT+DTRI=<DI1_TIRGGER_FlAG>,< DI2_TIRGGER_FlAG >
Example:
AT+ DTRI =1,0 (Enable DI1 trigger / disable DI2 trigger)
•Downlink Payload (prefix 0xAA 02):
0xAA 02 aa bb // Same as AT+DTRI=aa,bb
3.4.2.7 Trigger1 – Set DI1 or DI3 as trigger
Set DI1 or DI3(for LT-33222-L) trigger.
•AT Command:
AT+TRIG1=a,b
a :Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
b :delay timing.
Example:
AT+TRIG1=1,100(set DI1 port to trigger on high level, valid signal is 100ms )
•Downlink Payload (prefix 0x09 01 ):
0x09 01 aa bb cc // same as AT+TRIG1=aa,0x(bb cc)
3.4.2.8 Trigger2 – Set DI2 as trigger
Set DI2 trigger.
•AT Command:
AT+TRIG2=a,b
a :Interrupt mode. 0: falling edge; 1: rising edge, 2: falling and raising edge(for MOD=1).
b :delay timing.
Example:
AT+TRIG2=0,100(set DI1 port to trigger on low level, valid signal is 100ms )
•Downlink Payload (prefix 0x09 02 ):
0x09 02 aa bb cc// same as AT+TRIG2=aa,0x(bb cc)
Page 18 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
3.4.2.9 Trigger – Set AC (current) as trigger
Set current trigger , base on AC port. See trigger mode
•AT Command
AT+ACLIM
•Downlink Payload (prefix 0xAA 01 )
0x AA 01 aa bb cc dd ee ff gg hh // same as AT+ACLIM Seetrigger mode
3.4.2.10 Trigger – Set AV (voltage) as trigger
Set current trigger , base on AV port. Seetrigger mode
•AT Command
AT+AVLIMSeetrigger mode
•Downlink Payload (prefix 0xAA 00 )
0x AA 00 aa bb cc dd ee ff gg hh // same as AT+AVLIM See trigger mode
3.4.2.11 Trigger – Set minimum interval
Set AV and AC trigger minimum interval, system won't response to the second trigger within this set time after the
first trigger.
•AT Command
AT+ATDC=5Device won't response the second trigger within 5 minute after the first trigger.
•Downlink Payload (prefix 0xAC )
0x AC aa bb // same as AT+ATDC=0x(aa bb) . Unit (min)

Note: ATDC setting must be more than 5min
3.4.2.12 DO -- Control Digital Output DO1/DO2/DO3
•AT Command
There is no AT Command to control Digital Output
•Downlink Payload (prefix 0x02)
•0x02 aa bb cc// Set DO1/DO2/DO3 output
If payload = 0x02010001, while there is load between V+ and DOx, it means set DO1 to low, DO2 to high and DO3
to low.
01: Low, 00: High , 11: No action
Page 19 / 46 - last modified by Xiaoling on 2023/01/29 11:26

User Manual for LoRaWAN End Nodes - LT-22222-L LoRa IO Controller User Manual
Note: For LT-22222-L, there is no DO3, the last byte can use any value.
Device will upload a packet if downlink code executes successfully.
3.4.2.13 DO -- Control Digital Output DO1/DO2/DO3 with time control
•AT Command
There is no AT Command to control Digital Output
•Downlink Payload (prefix 0xA9)
0xA9 aa bb cc // Set DO1/DO2/DO3 output with time control
This is to control the digital output time of DO pin. Include four bytes:
First Byte: Type code (0xA9)
Second Byte: Inverter Mode
01: DO pins will change back to original state after timeout.
00: DO pins will change to an inverter state after timeout
Third Byte: Control Method and Ports status:
Fourth Byte: Control Method and Ports status:
Page 20 / 46 - last modified by Xiaoling on 2023/01/29 11:26