DiroDi xTreme User manual

xTreme
ASSEMBLY GUIDE
DiroDi

CONTACT
US
Address
G18, 425 Smith Street, Fitzroy VIC 3065
Melbourne, Australia
Phone
1800 571 930
E-mail
[email protected]
@ dirodiofficial
Website
www.dirodi.com.au

TABLE OF
CONTENTS

STEP 0
Tools required
STEP 1
Opening the box
STEP 2
Removing protective materials
STEP 3
Handlebars assembly
STEP 5
Front mudguard & light assembly
STEP 6
Installing pedals
06
08
12
16
26
31
STEP 4
Front wheel assembly
20

STEP 7
Installing the seat post
STEP 8
Pumping the tyres
STEP 9
Disk brake adjustment
STEP 10
Rear derailleur adjustment
STEP 11
Operating the bike
34
36
38
40
42

STEP 0
Tools required

DiroDi xTreme Assembly Guide - Tools required
07
Tools required for the assembly:
1x 10mm Wrench
1x 15mm Wrench
1x 4mm Alen key
1x 5mm Alen key
> 1

STEP 1
Opening the box

DiroDi xTreme Assembly Guide - Opening the box
09
1. Cut the plastic straps of the bike carton
(photos 1 & 2).
2. Open the carton door and take care so that the
staples do not cut you (photo 3).
> 1 > 2
> 3

DiroDi xTreme Assembly Guide - Opening the box
10
3. Remove the protective foams (photos 4 & 5).
4. Remove the small accessories box (photo 6).
> 6
> 5
> 4

DiroDi xTreme Assembly Guide - Opening the box
11
5. Lay the carton on the floor and Pull the bike out
of the carton (photo 7). It is better to put a mat in front of
the carton so that the bike frame does not get scratched.
6. Put the bike on a standing position (photo 8).
> 7
> 8
** Please note until the front wheel is assembled, the bike
is not stable on a standing position.
So please lean it against a wall or have someone hold the bike
until the front wheel assembly step is done.
(when you will be able to put the bike on the kickstand)

STEP 2
Removing protective
materials

DiroDi xTreme Assembly Guide - Removing protective materials
13
1. Remove all protective material from the bike
(photos 1, 2 & 3).
** Please take care so that the bike frame does not get
scratched.
> 3
> 1 > 2

DiroDi xTreme Assembly Guide - Removing protective materials
14
3. Open the accessories box (photo 6)
(Which includes the power adapter, basic assembly tools, pedals,
front mudguard assembly belts, bike manual and LCD manual).
> 6
2. Remove the front wheel off the pedal.
In order to release the wheel from the pedal, it might
be easier if you lift the rear wheel and turn the left
pedal anti-clockwise a bit and then remove the wheel
from the pedal (photos 4 & 5)
> 4 > 5

DiroDi xTreme Assembly Guide - Removing protective materials
15
4. After all protective materials are removed, your
bike should look the same as that in photo 7.
> 7

STEP 3
Handlebars assembly

DiroDi xTreme Assembly Guide - Handlebars assembly
17
1. Turn the stem of the bike anti-clock wise until the
stem and arch of the front fork faces forward
(photos 1 & 2).
2. Remove the 4 bolts and the stem plate by using a
4 mm Allen key (photos 3 & 4).
> 1
> 3 > 4
> 2

18
3. Put the handlebars in the stem.
Ensure the handlebar is centered and brake levers are
facing downward (photo 5).
> 5
4. Now adjust the angle of the display (photo 6).
> 6
DiroDi xTreme Assembly Guide - Handlebars assembly

19
5. Now tighten the bots by an Alley key. Please tighten
one bolt a bit and move to the next one and repeat
until all bolts are tightened (photos 7 & 8).
> 7
DiroDi xTreme Assembly Guide - Handlebars assembly
> 8

STEP 4
Front Wheel assembly