KneeRover KneeCycle User manual

KneeRover® KneeCycle
User Manual
Congratulations on your purchase of the KneeRover®
KneeCycle!
The deluxe KneeRover®KneeCycle provides a new level of
freedom to users recovering from foot, ankle or lower leg
injuries. This revolutionary product enables users to get back to
their daily routines and enjoy life while recovering –increasing
their mobility without the use of painful crutches.
Operating Instructions:
This medical device is designed to maximize mobility during your
recovery from foot/ankle surgery or injury.
Place the knee of your injured leg on the knee platform and stand as
straight as possible. Adjust the handlebar to waist height so the arms
and hands are in a comfortable position. Adjust the knee platform so
that your injured leg is supported at a 90 degree angle when standing.
Ensure that the hand brake is fully engaged before mounting the
KneeRover®scooter. To move the scooter, simply push forwards or
backwards with your good foot. Allow the scooter to glide, and as it
slows down, push again.
Safety First:
The KneeRover®scooter is designed for easy steering and stopping and
should be used to carefully move about at slow, controlled speeds.
When turning the scooter you should have the brake applied and be
moving at a slow, safe, controlled speed. It is easy to tip the scooter if
you are making a turn with too much speed. Use caution and balance
and operate at your own risk.
With routine use, nuts and bolts on the steering column, steering
mechanism, and brake mechanism can and likely will become loose.
Periodically check nuts and bolts after use and re-tighten as
appropriate.

KneeCycle Set Up Instructions:
Please follow the step by step instructions on the following pages to
properly assemble your KneeRover®scooter. The diagram below
identifies the key components of the scooter to aid with assembly.
Step 1: Install Front Axle
Please take your time to carefully complete all steps before operating
your new KneeRover®scooter. First, place the front axle with caster
wheels under the scooter frame, ensuring the round bolts by the wheels
are facing up (as shown in left and right photos). Align the axle and frame
holes, insert the clamp and washer into each hole, and tighten the clamps
in a clockwise motion until the axle is tight against the frame. Press the
clamp lever down firmly until it touches the frame, to lock it in place. The
right photo shows how the clamp should look when properly installed.
Step 2: Install Steering Mechanism
Attached to the front axle you will see two gray bars (the tie rods). Take
one of the tie rods and position it under the black plate that is attached to
the frame. Next take the other tie rod and place it on top of the black
plate. Place the washer on top of the upper tie rod and then thread the
bolt from the bottom to the top, through the tie rods. Finally thread the
cotter pin through the hole on top to lock the assembly in place.
Weight Capacity = 300 pounds
Hand Brake Lever
8” Non Marking
Wheels
Basket
Adjustable Knee
Platform
Handlebar Height
Adjustment Knob
Quick Release
Clamp
Steering Column
Brake Cable
Rear Brake
Mechanism
Removable Front
Axle
Clamp
Lever
Washer
Round Bolt
Proper Assembly of Tie Rods:
Black Plate
Upper Tie Rod
Washer
Cotter Pin
Lower Tie Rod
Bolt

Step 3: Install Steering Column
The steering column will be in a folded position when unpacking. When
facing the front of the KneeRover®scooter, raise the steering column and
push the security pin in the clamp to the left (as shown in left photo) to
allow the column to lock into place. Raise the clamp lever upward and
tighten by turning it clockwise. Finally, push clamp lever down firmly to
secure the steering column (as shown in center photo). Reverse these
steps when needing to lower steering column for transport. Once knee
platform is installed, use the black knob (shown in right photo) to set the
handlebars at a comfortable height for operation.
Step 4: Install Knee Platform & Attach Basket
The knee platform is designed to be used with either the right or left leg.
Remove the knee platform from the bottom of the KneeRover®scooter by
removing the locking pin and loosening the clamp. Next insert the knee
platform post into the receptacle tube and set the knee platform at your
desired height for use by inserting the locking pin through the aligned
holes. Finally, tighten the clamp to secure the knee platform in place.
Removable basket attaches to the steering column.
Step 5: Brake Operation
To engage the brake, squeeze the brake lever on handle bar.
Your KneeRover®scooter comes equipped with a brake lock /
parking brake. Simply squeeze brake handle firmly and press the
button to engage the lock. To release the lock, squeeze the brake
handle again.
Ongoing Maintenance
With routine use, nuts and bolts on the steering column, tie rod
steering mechanism, and brake assembly can become loose. To
ensure safe continuous operation of this KneeRover®scooter, it is
important to periodically inspect the scooter for loose nuts and
bolts and re-tighten as appropriate.
Push Pin to Left
Clamp
Lever
Locking
Pin
Brake Lock

Who we are:
We are committed to providing innovative and affordable mobility
solutions to get you moving as soon as possible after injury or surgery
and for the duration of your recovery –free to go about your busy,
active life –and have a little fun doing it. We are all about leaving the
painful crutches behind and giving you the Freedom to Move.
The KneeRover®Team is Driven to Change Your Outcome!
Your Satisfaction is Our Top Priority:
Thank you for your business –we appreciate having you as a customer!
We hope that you are completely satisfied with your purchase. If you
have any issues, please contact us and we will do everything possible
to help you. Reviews have a significant impact on our small business.
If you purchased this product on Amazon or eBay, we would greatly
appreciate a review once you’ve had a chance to use your new
KneeRover® scooter. We hope we’ve earned a 4 or 5 star review – if
not, please give us the opportunity to help you before leaving a review.
Thank you for your support. We appreciate you!
Need Help –Contact Us:
Phone: [phone]
Email: [e-mail]
Web: www.kneerover.com
Limited Lifetime Warranty
This warranty applies only to the original purchaser.
This device was built to exacting standards and carefully inspected
prior to shipment. Your KneeRover®brand product is warranted
to be free of defects in materials and workmanship for a period of
one year from the date of purchase. The side frames and cross
braces are warranted for the lifetime of the KneeRover®scooter.
This warranty does not cover device failure due to owner misuse,
negligence, or normal wear and tear. The warranty does not
extend to non-durable components, which are subject to normal
wear and need periodic replacement. These components include,
but are not limited to tires, grips, brake pads and upholstery.
The warranty shall not apply for damages or defects caused by
unauthorized parts, attachments or repairs, negligence, accident,
or any circumstances beyond the control of KneeRover®, such as
improper operation, maintenance or storage.
If you have any questions regarding your KneeRover®product or
this warranty, please contact our Customer Care Team. We are
available, for your convenience, toll free at 1-877-737-9877,
Monday –Friday from 9 am to 5 pm Eastern.
Need Parts or Accessories?
Add an accessory like a deluxe backpack, knee pad cover, cup holder
or headlight to enhance your experience on your new KneeRover®
scooter. Keep your scooter operating in top shape with original
manufacturer parts. Visit our exclusive online partner:
kneewalkershop.com, to explore our full range of parts and
accessories.
KneeRover®is a registered trademark of Capital Grade Imports LLC.