Dirty hand 107036 User manual

25-Ton & 30-Ton
Vertical/Horizontal Log Splitters
is safety alert symbol identies important safety messages in
this manual. Failure to follow this important safety information
may result in serious injury or death.
MODEL #’s 107036 (25-Ton) & 107079 (30-Ton)
Operation Manual
!
Part # 107171 Rev A

1100 W 120th Ave., Suite 600
Westminster, CO 80234 • 720-287-5182
For Service or Questions
Call 1-877-487-8275
720-287-5182
www.dirtyhandtools.com
Dirty Hand Tools® is a brand of

Table of Contents
Important Safety Information .....................................................4
Intended Use ..............................................................................4
Personal Protective Equipment ..................................................4
Safety Decals ..............................................................................5
General Safety ............................................................................6
Preparation of the Log ...............................................................6
Work Area ................................................................................. 6
Operation of the Log Splitter .....................................................7
Repair and Maintenance Safety ..................................................8
Hydraulic Safety .........................................................................8
Fire Prevention ...........................................................................9
Towing Safety ...........................................................................10
Unpacking & Assembly .............................................................11
Log Catcher Installation ..........................................................12
Operating Instructions...............................................................13
Engine Oil Recommendations .................................................13
Starting Instructions .................................................................14
Towing ..................................................................................... 16
Maintenance .............................................................................16
Assembly Overview ....................................................................17
Log Catcher Assembly ..............................................................18
Tank & Wheel Assembly ..........................................................19
Tank & Tongue Assembly .........................................................20
Beam Bracket Assembly ............................................................21
Beam & Tank Assembly ............................................................22
Hydraulic Line Assembly ..........................................................23
Tank & Engine Assembly ..........................................................24
Pump & Engine Assembly ........................................................25
Beam Assembly .........................................................................26
Tongue Assembly ......................................................................27
Log Splitter Replacement Parts .................................................28
Hardware Kit .............................................................................29
Log Splitter Accessories .............................................................30
Specications & Warranty ......................................... Back Cover
3

Important Safety Information
WARNING: Read and understand the complete Operation
Manual before assembling or using this product! Failure
to comprehend and comply with warnings, cautions and
instructions for assembly and operation could result in serious
injury or death.
Do not permit children to operate this equipment at any time. Do
not permit others that have not read and understood the complete
Operation Manual to operate this equipment. Operation of power
equipment can be dangerous. It is the sole responsibility of the
operator to understand the assembly and safe operation of this
product.
Call our customer service department at 720-287-5182,
1-877-487-8275, or visit www.dirtyhandtools.com if you have any
questions or concerns about the safe operation of this equipment.
INTENDED USE
Do Not Use the log splitter for any purpose other than splitting
wood, for which it was designed. Any other use is unauthorized
and may result in serious injury or death.
PERSONAL PROTECTIVE EQUIPMENT
When operating this log splitter it is essential that you wear safety
gear including goggles or safety glasses, steel toed shoes and tight
fitting gloves (no loose cuffs or draw strings). Always wear ear
plugs or sound deafening headphones to protect against hearing
loss when operating this log splitter.
Do Not wear loose clothing or jewelry that can be caught by
moving parts of the log splitter. Keep clothing and hair away
from all moving parts when operating this log splitter.
4
!
WARNING
!
DANGER
!
CAUTION

5
Important Safety Information
SAFETY DECALS
Make sure all safety warning decals are attached and in readable
condition. Replace missing or defaced decals. Contact Dirty Hand
Tools at 1-877-487-8275 for replacement decals.
OPERATING INSTRUCTIONS
CONTROL VALVE
OPERATION
For repair or service please call 1-877-487-8275
RETRACT
EXTEND
100212
WARNING
READ
MANUAL
BEFORE
OPERATION
TO AVOID SERIOUS INJURY OR DEATH:
WEAR
PROTECTIVE
HEAD
GEAR
WEAR
GOGGLES OR
PROTECTIVE
EYEWEAR
WEAR
NOISE
DEAFENING
HEADPHONES
WEAR
PROTECTIVE
FOOTWEAR
WEAR
GLOVES
DO NOT USE
HANDS TO
CHECK FOR
LEAKS
AVOID PINCH
POINTS
KEEP AWAY
FROM MOVING
PARTS
· STAY WITHIN DESIGNATED OPERATION ZONE
· KEEP PETS AND BYSTANDERS AWAY
· NEVER REACH OVER SPLITTER DURING OPERATION
· DO NOT OPERATE IN ENCLOSED SPACE
· KEEP BODY & CLOTHING AWAY FROM MOVING PARTS
· OPERATE ONLY WHEN COMPLETELY ALERT
1. PLACE LOG SPLITTER ON A STABLE, FLAT SURFACE
2. START ENGINE & ADVANCE THROTTLE TO MAXIMUM
3. PLACE LOG ON CRADLE AGAINST FOOT PLATE
4. MOVE VALVE HANDLE TOWARDS FOOT PLATE TO
EXTEND THE WEDGE AND SPLIT THE LOG
5. MOVE VALVE HANDLE TOWARDS THE OPERATOR TO
RETRACT THE WEDGE FROM THE LOG
NOTE: SPLIT WOOD IN DIRECTION OF THE GRAIN
Tank oil level should always be kept between the “MAX”
and “MIN” lines indicated on the dipstick. Never fill the
reservoir above the “MAX” line. Consult the Operation
Manual for maximum system and operating fluid
capacities. Select oil viscosity based on the outside
temperature at the time of operation in the table below.
100207C
Operator Zone Decal Part # 100399
Oil Level Decal Part # 100207
Operation Decal Part # 100212
TO AVOID SERIOUS INJURY OR DEATH
●Read the Operation Manual on how to attach the
coupler to the hitch ball and how to tow safely.
●Ensure the correct ball size is being used.
●Do not exceed hitch ball or coupler load limits.
●Attach and secure safety chains prior to towing.
●Do not exceed maximum towing speed of 45 mph.
●Avoid sharp turns and steep angles.
●Check tightness of the coupler before towing.
●Replace the hitch ball or coupler if damaged. 100208
WARNING
Warning Decal Part # 100208
100204
DANGER
PINCH POINT
HAZARD
KEEP CLEAR
DURING
OPERATION
Pinch Point Decal Part # 100204
106047
HOT
SURFACE
DO NOT TOUCH
CAUTION
Hot Surface Decal Part # 106047
ATTENTION
START ENGINE,
CYCLE CYLINDER 3 - 4
TIMES, STOP ENGINE
ADD 32 - 64 FLUID OZ.
AW46 HYDRAULIC
FLUID BEFORE
OPERATION.
107163
Hydraulic Fluid Decal
Part # 107163

6
Important Safety Information
GENERAL SAFETY
Failure to follow warnings, cautions, assembly and operation
instructions in the Operation Manual may result in serious
injury or death.
Read the Operation Manual before operation.
• Do not permit children to operate this equipment at any time.
Do not permit others that have not read and understood the
complete Operation Manual to operate this equipment.
• Keep all people and pets a minimum of 10 feet away from the
work area when operating this log splitter. Only the operator is
to be near the log splitter during use.
• Do not operate the log splitter when under the influence of
alcohol, drugs or medication.
• Do not allow a person who is tired or otherwise impaired or not
completely alert to operate the log splitter.
PREPARATION OF THE LOG
Both ends of the log should be cut as square as possible to prevent
the log from rotating out of the splitter during operation.
Do not split logs greater than 25 in. in length.
WORK AREA
• Do not operate the log splitter on icy, wet, muddy or otherwise
slippery ground. ONLY operate your log splitter on level ground.
Operating on a slope could cause the log splitter to roll over or
logs to fall o of the equipment, which could result in injury.
• Do not operate the log splitter in an enclosed area. Exhaust
fumes from the engine contain carbon monoxide which can be
harmful or deadly when inhaled.
• Do not move the log splitter over hilly or uneven terrain without
a tow vehicle or adequate help.
• Use a tire chock or block on the wheels to prevent movement of
the log splitter while in operation.
• Operate the log splitter in daylight or under good artificial light.
• Keep the work area free of clutter. Remove split wood from
around the log splitter immediately after each use to avoid
potential tripping.
!
DANGER
!
DANGER

7
Important Safety Information
OPERATION OF THE LOG SPLITTER
Operate the log splitter from within the operation zone as shown
in the diagrams below. e operator has the safest and most
efficient access to the control valve and the beam in these locations.
Failure to operate the log splitter in this position can result in
serious injury or death.
• Make sure the operator knows how to stop and disengage the
controls before operating.
• Do not place hands or feet between the log and splitting wedge
during forward or reverse stroke. Serious injury or death could
result.
• Do not straddle or step over the log splitter during operation.
• Do not reach or bend over the log splitter to pick up a log.
• Do not attempt to split two logs on top of each other.
• Do not attempt to cross split a log.
• Do not attempt to load your log splitter when the ram or wedge
is in motion.
• Use your hand to operate the control lever on the valve. Do not
use your foot, a rope or any extension device.
• Do not move the log splitter while the engine is running.
• Never leave the equipment unattended while the engine is
running. Shut off the engine even if you are leaving the log
splitter for a short period of time.
• Avoid contact with the muffler and other hot areas of the engine
during operation or after running to prevent burns.
!
DANGER
!
DANGER

8
Important Safety Information
REPAIR AND MAINTENANCE
• Do not operate the log splitter when it is in poor mechanical
condition or in need of repair. Frequently check that all nuts,
bolts, screws, hydraulic fittings and hose clamps are tight.
• Do not alter the log splitter in any manner. Any alteration will
void the warranty and could cause the log splitter to be unsafe
to operate. Perform all recommended maintenance procedures
before using the log splitter. Replace all damaged or worn parts
immediately.
• Do not tamper with the engine to run it at excessive speeds.
e maximum engine speed is preset by the manufacturer and is
within safety limits. See Kohler engine manual.
• Remove the spark plug wire before performing any service or
repair on the log splitter.
• Always check the level of hydraulic oil and engine oil before
operation.
• Replacement parts must meet manufacturer’s specifications.
HYDRAULIC SAFETY
e hydraulic system of the log splitter requires careful inspection
along with the mechanical parts. Be sure to replace frayed, kinked,
cracked or otherwise damaged hydraulic hoses or hydraulic
components.
• Check for hydraulic uid leaks by passing a piece of paper or
cardboard underneath or over the area of the leak. Do not check
for leaks with your hand. Fluid escaping from the smallest hole,
under pressure, can have enough force to penetrate the skin causing
serious injury or death.
• Seek professional medical attention immediately if injured
by escaping hydraulic uid. Serious infection or reaction can
develop if medical treatment is not administered immediately.
• Relieve all pressure by shutting off the engine and moving the
valve control handle back and forth should it become necessary to
loosen or remove any hydraulic fitting.
• Do not remove the cap from the hydraulic tank or reservoir while
the log splitter is running. e tank could contain hot oil under
pressure which could result in serious injury.
• Do not adjust the hydraulic valve. e pressure relief valve on
the log splitter is preset at the factory. Only a qualied service
technician should perform this adjustment.
!
WARNING

9
Important Safety Information
FIRE PREVENTION
• Do not operate the log splitter near an open flame or spark.
Hydraulic oil and gasoline are ammable and can explode.
• Do not fill the gas tank while the engine is hot or running.
Allow the engine to cool before refueling.
• Do not smoke while operating or refueling the log splitter. Gas
fumes can easily explode.
• Refuel the log splitter in a clear area with no gas fumes or spilled
gas. Use an approved fuel container. Replace the gas cap securely.
If gasoline has spilled, move the log splitter away from the area
of the spill and avoid creating any source of ignition until the
spilled gas has evaporated.
• Keep a Class B fire extinguisher on hand when operating this log
splitter in dry areas as a precautionary measure against possible
flying sparks.
• Drain the fuel tank prior to storage to avoid the potential fire
hazard. Store gasoline in an approved, tightly sealed container.
Store the container in a cool, dry place.
• Turn the fuel shut off valve on the engine to the “OFF” position
before towing the log splitter. Failure to do so may result in
flooding the engine.
IMPORTANT NOTE:
is log splitter is equipped with an internal combustion engine
and should not be used on or near any unimproved forest-covered,
brush-covered or grass-covered land unless the engine’s exhaust
system is equipped with a spark arrester meeting applicable
local or state laws (if any). If a spark arrester is used, it should be
maintained in effective working order by the operator. In the state
of California a spark arrester is required by law. Other states have
similar laws.
Federal laws apply on federal lands. A spark arrester muffler
(optional by manufacturer) is available as an accessory at your
nearest engine dealer. Always check the legal requirements in your
area.
!
CAUTION
!
CAUTION

10
Important Safety Information
TOWING SAFETY
•Check all local and state regulations regarding towing, licensing,
and lights before towing your log splitter.
• Check before towing to make sure that the log splitter is
correctly and securely attached to the towing vehicle and that the
safety chains are secured to the hitch or bumper of the vehicle
with enough slack to allow turning. Always use a Class I, 2” ball
with this log splitter.
• Do not carry any cargo or wood on the log splitter.
• Do not allow anyone to sit or ride on the log splitter.
• Disconnect the log splitter from the towing vehicle before
operating it.
• Use care when backing up with the log splitter in tow to avoid
jack-knifing. Allow for added length of the log splitter when
turning, parking, crossing intersections and in all driving
situations.
• Do not exceed 45 mph when towing your log splitter. Towing
the log splitter at speeds higher than 45 mph could result in loss
of control, damage to the equipment, serious injury or death.
Adjust towing speed for terrain and conditions. Be extra cautious
when towing over rough terrain especially railroad crossings.
!
CAUTION

Unpacking & Assembly
List of tools needed for assembly:
• Needle nose pliers • Scissors • Box Cutter or knife
• (2) 17mm wrenches • (2) 19mm wrenches
IMPORTANT:e hydraulic tank is pre-lled with AW46 hydraulic
uid and the engine is pre-lled with 10W30 engine oil at the factory.
Two (2) people may be required for assembly
1. Cut and remove the box and additional packaging.
2. Cut and remove banding using scissors.
3. Remove engine guard by removing the lynch pin
underneath the engine (see arrow). Recycle engine guard.
4. Cut and remove bag around the tow coupler, cut zip tie and
lower tongue . Extend tongue stand .
5. Remove bolts, washers, and nuts from
tongue mount bracket on tank.
6. Slide tongue into the mounting bracket , aligning
the two holes in the tongue with the two holes in the
bracket and secure with hex bolt , washer , lock
washer and hex nut , in two places.
7. Lower beam into the horizontal position and secure beam
latch . Two people may be required to complete operation.
8. Attach valve handle into operational position and secure
with clevis pin and cotter pin .
9. Remove log splitter from metal pallet and recycle pallet.
Two people may be required to complete operation.
10. Check all fittings and hardware for tightness.
6
3
5
8
7
6
13
14
15
4
9
11
10
12
Item Description Qty.
1 Metal Pallet 1
2 Engine Guard 1
3 Tongue & Stand Assembly 1
4 Tongue Stand 1
5 Hex Bolt, M12 x 1.75 x 1.10mm, G8.8 2
6 Flat Washer, M12 4
7 Lock Washer, M12 2
8 Hex Nut, M12 x 1.75, G8.8 2
9 Valve Handle 1
10 Clevis Pin, 1/4 in. x 1/2 in. 1
11 Cotter Pin, 1/16 in. x 1/2 in. 1
12 Detent Valve 1
13 Beam & Cylinder Assembly 1
14 Beam Lock Bracket 1
15 Tongue Mount Bracket 1
2
1
11
3
!
WARNING
2
4
5678
15
9
10 11
1
14
153
56
78

12
Item # Part # Description Qty.
1 100157 Log Catcher Grate 1
2 100165 Hex Bolt, M10 x 1.5 x 30mm, G8.8 2
3 100161 Flat Washer, M10 6
4 100089 Lock Washer, M10 4
5 100009 Hex Nut, M1 x 1.5, G8.8 4
6 100064 Button Screw, 2
M10 x 1.5 x 30mm, G8.8
Log Catcher Installation (30-Ton)
NOTE: e 25-Ton Log Splitter does not come with a log
catcher, which is available as an accessory.
1. Rotate Beam & Cylinder Assembly down from upright
position and lock in place with the release pin.
2. Install the Log Catcher Assembly 1with Hex Bolts, M10 x
1.5 x 30mm 2; Flat Washer, M10 3; Lock Washer, M10 4;
Hex Nut, M10 x 1.5 5; and Button Screw, M10 x 1.5 x 30mm
6; in 2 places. Tighten hex nuts securely with a 17mm socket
wrench and tighten button screws with 6mm hex key wrench.

13
Operating Instructions
WARNING: Read and understand the complete Operation
Manual before assembling or using this product! Failure
to comprehend and comply with warnings, cautions and
instructions for assembly and operation could result in serious
injury or death.
Do not permit children to operate this equipment at any time.
Do not permit others that have not read and understood
the complete Operation Manual to operate this equipment.
Operation of power equipment can be dangerous. It is the sole
responsibility of the operator to understand the assembly and safe
operation of this product.
Call our customer service department at 720-287-5182,
1-877-487-8275, or visit www.dirtyhandtools.com if you have
any questions or concerns about the safe operation of this
equipment.
e hydraulic reservoir should be lled with hydraulic uid
and the engine should be lled with engine oil
before starting or operation.
STEP 1: Add approximately 4 gallons of hydraulic fluid. e
remaining hydraulic fluid will be added after the cylinder
is cycled. AW32 or AW46 hydraulic oil is recommended.
Automatic transmission fluid can be substituted instead of
hydraulic oil when temperatures are below 32°F. Use only clean
oil and take care to prevent dirt from entering the hydraulic
reservoir.
ENGINE OIL RECOMMENDATIONS
Use 4-stroke automotive detergent oil. SAE 10W-30 is
recommended for general use. Refer to the SAE Viscosity
Grades chart in your engine owner’s manual for average
temperature ranges. e engine manufacturer recommends using
API SERVICE Category SE or SF oil. e engine oil capacity is
20 oz. for Kohler SH265 (22-Ton/27-Ton) and 40 oz. for Kohler
CH395 (35-Ton). Always check oil level before starting the
engine and keep level full.
!
DANGER
!
CAUTION

14
Operating Instructions
Step 2: After the hydraulic reservoir and the engine crankcase
are filled with oil, start the engine. e hydraulic pump is
self-priming. With the engine running, move the hydraulic
valve lever toward the foot plate. is will cause the cylinder
to extend and expel air. When the cylinder is fully extended,
retract it. Repeat this procedure several times. An erratic
movement of the cylinder indicates that there is still air in the
system. Add about 1.0 to 1.5 gallons of hydraulic fluid. Five
gallons will register just above the top fill line on the dip stick.
e total capacity of the entire hydraulic system is 6.5 gallons
with 5 gallons of hydraulic fluid the minimum required to
operate.
NOTE: If the tank is overlled it will expel oil from the
breather cap when the cylinder is retracted. Cycle the
cylinder again until it has a constant speed which indicates
that all air has been expelled.
STARTING INSTRUCTIONS
NOTE: Refer to the Engine Owner’s Manual for complete
information on starting, maintenance and troubleshooting.
1. Move the fuel valve lever to the ON position.
2. To start a cold engine, move the choke lever to the CLOSE
position. To restart a warm engine, leave the choke lever in
the OPEN position.
3. Move the throttle lever away from the SLOW position,
about 1/3 of the way toward the FAST position.
4. Turn the engine switch to the ON position.
5. Pull the starter grip until you feel resistance, then pull
briskly. Return the starter grip gently.
6. If the choke lever has been moved to the CLOSE position
to start the engine, gradually move it to the OPEN position
as the engine warms up.
7. To stop the engine in an emergency, simply turn the engine
switch to the OFF position. Under normal conditions,
move the throttle lever to the SLOW position and then
turn the engine switch to the OFF position. en turn the
fuel valve lever to the OFF position.
For further information on starting and stopping the engine,
refer to your engine owner’s manual.

15
Operating Instructions
CAUTION:Turn Fuel Shut O Valve to the “O ” position
before towing to avoid ooding the engine.
NOTE: e engine‘s maximum speed is factory preset at 3600
RPM as the no load speed.e throttle should be set at the
maximum speed for wood splitting to reach the horsepower
required for the pump.
WARNING: Review safety information related to operation of
the log splitter on pages 4-10 of this manual. Make sure that you
have the recommended personal protective equipment described
on page 4.
1. Set up the log splitter in a clear, level area and block the
wheels. Make sure that the suction port on the tank is always
on the lower side of the log splitter.
2. For horizontal operation place a log on the beam against the
foot plate. Make sure the log is securely on the foot plate and
against the beam. To split wood in the vertical position, release
the pin on the beam latch located on the front end of the
beam. Carefully tilt the beam up until the foot plate is sitting
squarely on the ground and the log splitter is stable. Place
the log on the foot plate against the beam. When the beam is
returned to the horizontal position make sure the beam latch
is securely locked down.
3. With the engine running, depress the valve handle so that the
cylinder will drive the wedge into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not
completely split after the cylinder has reached the end of its
extension, retract the cylinder.
IMPORTANT: Leaving the valve in the “actuate” position at the
end of the stroke may damage the pump. Always use extra care
when splitting logs with unsquare ends.
Store manuals in the Manual Cannister attached to the tongue
of the log splitter or le in a safe place for future reference.
!
CAUTION
!
WARNING

16
Operating Instructions
NOTE: For operation in wooded areas, obtain a spark arrestor
for the exhaust system. See the engine operating and maintenance
manual and check with your authorized service center. See also
Fire Prevention on page 9 of this manual.
IMPORTANT:To extend the life of the hydraulic cylinder
avoid bottoming out the wedge plate to the foot piece.
To conform with industry safety recommendations the wedge
stops 1/2 inches from the end of the stroke.
TOWING
is log splitter is equipped with pneumatic tires, a Class I coupler
(2 in. diameter ball required) and safety chains. Before towing,
the safety chains must be secured to the hitch or bumper of the
vehicle. Local regulations should be checked regarding licensing,
lights, towing, etc. Turn fuel shut off valve on the engine to the
“Off ” position prior to towing. Failure to do so may result in
flooding the engine. Do not exceed 45 mph when towing this log
splitter. See also Towing Safety on page 10 of this manual.
MAINTENANCE
1. Consult the operating and maintenance instructions of the
engine manufacturer for engine care and maintenance.
2. Always check the oil level of the hydraulic reservoir before
operation. Operating the log splitter without an adequate oil
supply will cause severe damage to the pump.
3. Change the oil filter after the first 25 hours of operation.
ere after change the oil filter every 100 hours or seasonally,
whichever comes first.
4. To drain the hydraulic oil, loosen the clamp on the hose
coming from the fitting on the bottom of the tank. It is located
just to the right of the oil filter.
5. If the wedge becomes dull or nicked, it can be removed and
sharpened. Remove the bolt that connects the wedge to the
cylinder. e hose from the valve may need to be removed.
Carefully lift the cylinder to allow the wedge to slide forward.
e wedge can now be lifted off and sharpened.
6. Clean the breather cap after 25 hours of operation. Clean
it more often when operated in dusty conditions.To clean,
remove the breather cap from the tank and flush with kerosene
or liquid detergent to remove the dirt.
7. See Repair and Maintenance on page 8 of this manual.
8. All replacement parts must meet manufacturer’s specifications.

Assembly Overview
Item # Part # Description Qty.
1 107164 Tank & Engine Assembly (25-Ton) 1
107165 Tank & Engine Assembly (30-Ton)
2 100065 Tongue & Stand Assembly 1
3 107166 Beam & Cylinder Assembly (25-Ton) 1
107167 Beam & Cylinder Assembly (30-Ton)
4 100062 Wheel/Tire Assembly, 4.80 x 8 in. 2
5 100150 Beam Lock Bracket 1
6 100087 Beam Pivot Bracket 1
7 101391 Log Catcher Assembly (25-Ton)* 1
100173 Log Catcher Assembly (30-Ton)
* Item not included with Model 107036 (25-Ton)
**Item not shown
17

Item # Part # Description Qty.
1 100157 Log Catcher Grate 1
2 100154 Log Catcher Support Plate 2
3 100155 Log Catcher Mount, Lower 2
4 100152 Log Catcher Mount, Upper 2
5 100165 Hex Bolt, M10 x 30mm 8
6 100089 Lock Washer, M10 10
7 100009 Hex Nut, M10 10
8 100161 Flat Washer, M10 12
9 100064 Button Head Screw, M10 x 30mm 2
Log Catcher Assembly
7
8
4
5
2
6
3
1
7
9
18
89
6
9
8
7
6
7
2
3
1
4
5
Item # Part # Description Qty.
1 100929 Log Catcher Grate 1
2 100934 Support Arm, Large Right 1
3 100933 Support, Right 1
4 100930 Support Arm, Left 1
5 100931 Support Arm, Large Left 1
6 100165 Hex Bolt, M10 x 30mm 8
7 100009 Hex Nut, M10 8
8 100089 Lock Washer, M10 8
9 100181 Flat Washer, M12 8
101391
Log Catcher Assembly
For 25-Ton
100173
Log Catcher Assembly
For 30-Ton

Tank and Wheel Assembly
Item # Part # Description Qty.
1 107164 Tank & Engine Assembly (25-Ton) 1
107165 Tank & Engine Assembly (30-Ton)
2 100062 Wheel/Tire Assembly, 4.80 x 8 in. 2
3 100142 Flat Washer, 3/4 in. 2
4 100140 Castle Nut, 3/4-16, Clear Zinc 2
5 100143 Cotter Pin, 1/8 in. x 1-1/2 in. 2
6 100063 Hub Cap 2
7 100162 Hub Cap Tool 1
19

Tank and Tongue Assembly
Item # Part # Description Qty
1 107164 Tank & Engine Assembly (25-Ton) 1
107165 Tank & Engine Assembly (30-Ton)
2 100065 Tongue & Stand Assembly 1
3 100200 Hex Bolt M12 x 1.75 x 1.10mm, G8.8 2
4 100181 Flat Washer, M12 10
5 100023 Lock Washer, M12 8
6 100022 Hex Nut, M12 x 1.75, G8.8 8
20