Discount Car Stereo BECKER BT-BKRTKMki User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
Radio shown for illustration purposes only
BT-BKRTKMki
QUICK REFERENCE GUIDE FOR BECKER RADIOS WITH CD CHANGER
Created December 22, 2016
Revised: June 10, 2020

Introduction:
Most Bluetooth car kits include a universal harness that may or may not fit the
radio in your vehicle and as a result splicing and/or cutting the vehicles harness
will be required to complete the install. Purchase this installation harness to
quickly install Motorola TK30 and select Parrot MKi Hands-free kits to Becker
radios with optional CD changer(vehicle MUST HAVE a working CD changer).
Installation:
We recommend disconnecting the car battery. But before
anything locate and record the radio safe code. Don’t
disconnect battery if radio code is not available, otherwise
radio will cease to operate.
1. Remove radio from dash to gain access to the connectors. A set of
Radio removal tools (See Fig. 1) is required.
Fig. 1
Radio removal Tools
Fig. 2
2. Slide tools into radio slots (51) (Straight edge facing away). Withdraw radio
by pulling outwards. To release keys simply press retaining springs. See
Fig. 2. Click here for more regarding removal tools.
3. Disconnect blue (C-3) green (C-2) plugs and yellow (C-1) plugs from radio
cavity (See Fig. 3)
Fig. 3
radio connectors
4. Connect installation harness yellow, green and blue plugs (See Fig. 4)
to their respective slots on radio. (Chamber C as seen in Fig. 3).

Fig. 4
Audio harness
5. Connect factory harness yellow, green and blue plug to installation
harness red plug as seen in Fig. 5
Fig. 5
6. Disconnect radio 8-pin plug from chamber A (See Fig. 3) and connect
to installation harness 8-pin connector (See Fig. 6)
7. Connect installation harness 8-pin plug (See Fig. 6) to radio cavity
vacated in step 6 (See Fig. 3)
Fig. 6
7. Connect installation harness 22-pin Molex plug (See Fig. 7) to Motorola
or Parrot hideaway module
Fig. 7
8. Install microphone (See Fig. 8) to visor and route plug down the side
pillar, under the dash and toward the radio cavity and connect to “MIC”
input on Module (See Fig. 7)

Proceed with microphone, module installation according to guide included with
kit.
Reminders:
1. The factory CD Changer is required and remains connected otherwise this
kit will not work as intended.
2. Radio must be in CD mode to for music streaming etc.
Frequent asked questions
1. Why purchase the BT-BKRTKMki?
The BT-BKRTKMki harness allows for quick installation of:
Motorola TK30 (will not fit other Motorola kits) and
Parrot MK6000/6100, MKi9000/9100 and MKi9200
2. Why should I purchase this harness instead of using the one included
in Bluetooth Kit?
The installation harness included with the aforementioned kits can be used
in most application except in vehicles equipped with factory amplifiers.
The BT-BKRTKMki can be used in vehicles with or without amplifiers.
3. Why is a CD changer required to install my Hands Free, music
streaming kit to the CD-210 and CDR-210 and other?
Becker CR-210 and CDR-210 and others, does not have “AUX IN” port
required for music streaming feature to work. This harness uses the CD
changer audio port for music streaming. CD changer playback is impaired;
however, the CD changer must remain connected.
Disclaimer
• this product has no affiliation with Becker or Apple
• we’re not liable for misuse of this product.
Email [e-mail]
© 1995-2020-06-10 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.