Discount Car Stereo A2DIY-JAG97 Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2DIY-JAG97
QUICK START BLUETOOTH INSTALLATION GUIDE FOR SELECT PRE-1998 JAGUAR CD CHANGER CONTROLLING RADIOS.
Created February 6, 2019
Revised: September 13, 2021

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements
OEM Radio with CD button on faceplate and 8-pin port at the rear
Introduction
Just because you drive an order car does not mean you have to settle for old
technology. Any pre-1998 Jaguar with CD changer controlling radio (TAPE/CD
button) is compatible with this module and able to make/received phone calls,
stream apps (Music, GPS etc.) and also connect and play an AUX device (e.g. MP3
player, iPod, Sat radio etc.) In addition, an optional USB charging por enables
charging those current hungry devices while on the road. Update older Jaguars
to support Bluetooth features only available on newer cars.
Warning: This module installs behind the radio cavity and requires radio
removal. CD changer (if present) must be disconnected—See our A2DIY-
JAG97CD to retain CD changer playback.
Installation
Radio removal required to access CD connector on radio
For help removing radio, click link below:
https://www.youtube.com/watch?v=vpAIdr6V3iE
1. Disconnect CD changer cable (if present) from “CD” connector on
radio
2. Connect module 8-pin plug (See Fig. 1) to radio 8-pin CD connector
(See Fig. 2)
Fig. 1
Fig. 2
radio
3. Connect supplied (3ft.) audio cable (See Fig. 3) to Module “AUX” input
jack, (See Fig. 4), route other end to dash area or location where
device resides (within 3ft).

Fig. 3
3ft. Audio cable
Fig. 4
Module
4. Install microphone to headliner with included visor clip
5. Route microphone cable (10 ft. long) down pillar, under dashboard and
into radio cavity
6. Connect microphone jack to module “MIC” input. (See Fig. 5)
Wind noise (Convertibles) will negatively affect phone audio. Users are
advised to install microphone away from wind/ventilation ducts etc. or
opt for push button microphone seen in Fig. 7
Visor microphone
Fig. 5
7. Connect/splice/tap module red wire (See Fig. 6) to a 12V accessory
(switched) supply in vehicle. 12V accessory or switched supply may
be available at cigar lighter Orange/Brown wire, radio 14-pin plug pin 11
(Light Green/Orange or White/yellow) etc.
Warning: Do not connect/tap red wire to 12V battery (always on)
supply.
Fig. 6
Optional charging kit
Optional USB charger can be added to the A2DIY-JAG97 Kit. Should you decide to
add it, we suggest one of 3 connecting options:
A. Flush to dash/panel requires drilling a ¾” hole
B. Flush with Support bracket (Mount USB terminal wherever your installation
demands without drilling)
C. USB port- (default)

A. Flush to Dash or Panel (drilling required)
1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent
(See Fig. 10)
Fig. 10
Step drill bit
2. Insert supplied 3ft. USB male terminal (See Fig. 11) through hole
created in step 1 and connect to module USB port (See Fig. 12)
Fig. 11
Flush mount 3 ft. USB cable
Fig. 12
USB port
3. Snap USB head (See Fig. 13) in place and flush with mounting surface
(See Fig. 14)
Fig. 13
USB head
Fig. 14
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and test operation
B. Bracket Mount (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. of module and
mount USB support bracket (See Fig. 15) to surface using
adhesive/tape or screws (included).

Fig. 15
USB mounting bracket
2. Insert male terminal through hole in bracket (See Fig. 16) and connect
to module USB port (See Fig. 12)
Fig. 16
3. Snap USB head (See Fig. 16) to bracket until flush (See Fig. 17)
Fig. 17
4. Tuck and secure any extra wire away from moving parts and test
operation ( See Bluetooth Pairing and Connection )
Media button
Pairing: Ensure Bluetooth is enabled on your device (e.g., Smartphone/Tablet
etc.) scan/search for available devices and select BT009 from list. Media
button can be paired with multiple devices but can only operate one at a time.
Fig. 18
Installing:
Attach button to steering wheel (includes holder) or dashboard to safely and
conveniently control multi-media functions even when smartphone is out of
reach.
Charging:
Media button has a built-in rechargeable 200mAH battery which may last up to
10 days. Use supplied USB cable to connect media button to charging source.
Reaches full charge after 2 hours.