Discovery Telecom Driftwood 4118R User manual

SAFETY FIRST !!!!!
4118R / 4218R / 4818R Twin/Full Bunk Bed
All of Discovery’s Bunkbeds were designed and manufactured with your child’s safety as our top priority. Their
unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-13
“Standard Consumer Safety Specification for Bunk Beds” and Code of Federal Regulations (CFR) 1213 “Safety Standards
for Entrapment Hazards in Bunk Beds” and (CFR) 1513 “Requirements for Bunk Beds”.
Safety is a cooperative effort between us as the manufacturer, and you as a guardian. Please read and consider the warnings listed
below when choosing a mattress and discussing rules of use with your child.
SAFETY WARNINGS
1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on the upper bunk.
6. Periodically, check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Always use guardrails on both long sides of the upper bunk. If bunk bed will be placed next to the
wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent
entrapment between the bed and wall.
12. The use of water or sleep flotation mattresses is prohibited.
13. Keep these instructions for future reference.
STRANGULATION HAZARD –Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts and
jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only Twin or Full Mattress with the following specifications on upper & lower bunks
Twin Mattress :37 1/2” - 38 1/2” Wide x 74”-75” long
Full Mattress :52 1/2” - 53 1/2” Wide x 74”-75” long
Ensure thickness of mattress and foundation combined does not exceed 10 inches and mattress is at least
5 inches below upper edge of guardrails.
******Replacement parts, including additional guardrails, may be obtained from any Discovery dealer or
directly from us at the below address.
DiscoveryDiscovery
World FurnitureWorld Furniture
TMTM
ASSEMBLY INSTRUCTIONS
“Driftwood Collection”
www.discoveryworldfurniture.com
2963 Stonewall Place
Sanford, Fl, 32773
June-2019
Sand Gray Chestnut

4118R / 4218R / 4818R Twin/Full Bunk Bed
Replacement Parts & Limited Lifetime Warranty
Discovery World Furniture will replace any component part free of charge for 1 full year via UPS freight collect. In addition,
Discovery World Furniture will replace any component part for 50% of the then prevailing retail price plus freight for the lifetime of
the product unless the product has been discontinued from our line. For service, mail your request to: Discovery World Furniture
2963 Stonewall Place, Sanford, Fl, 32773. Website www.discoveryworldfurniture.com
D
BMetal Dowel 3 1/2 x 3/8”
1/4"X3 1/8" (80mm)
1/4" X 2 3/8" (60mm)
A
02
05
G
H
I
F
E
Wooden Dowel 1 3/4”
Wooden Blocks
04
16
16
04
04
01 02
5/32"X1 5/8"
Allen wrench
C1/4"X 1 1/2" (40mm)
Requires a phillips screw driver not included
Sand Gray Chestnut

01
2x
3x
05
H
H
H
H
H
H
H
H
12
02
09
01
01
03
10
13
14
12
12
12
05
06
08
08 07
04
Block
I
Block
Assembled ladder I
H
H
Parts List

A
E
2
3
10
09
12
12
A
A
A
A
G
A
A
A
A
A
G
G
G
G

5
4
A-B
E
B
B
B
B
A
A
A
A
A
A
A
A
01
01
12
05
C
C
C
C
C
E
A
B
C

6
7
F
F
F
F
I
F
F
Very Important:
These blocks must be
attached to comply
with ASTM standards
F

8
9
Refer to the next page for the slats installation
14
13
D
C
D
Choose a side and install the ladder
04

A (1)
A
B(4) (4) (4) (1) (1) (24)
CDE F P
Step-1
Step-2
Attach tube (A) under one of the metal slat sections
using parts (B,C,D) as shown
Attach the second section of the metal slats to the tube (A)
as shown below.
DWF ( FULL SIZE METAL SLAT KIT INSTRUCTION)
(42” tube)
D
B
C
E
F
1/2”
Step-3 Install the complete slats to one side of the bed always starting
flush with the end of the cleat using the screws (P)
Always Start here
(Find these hardware in Slat box)
P
P
P
P
P
P
P
P
P
P
P
P