Discovery Telecom EWS3 User manual

EWS3
WIRELESS INDOOR SIREN
Тел: [phone]
Моб: [phone]
Skype: Discoverytelecom
Mail: [email protected]
www.discoverytelecom.ru

2
2
EN EWS3 – Wireless Indoor Siren
User Manual v1.0
Compatible with:
• ESIM364 v02.06.09 and up.
• EPIR2 v01.01.12 and up.
• ESIM264 v7.14.07 and up.
Main features:
• Audio alarm indication by 2 built-in speakers.
• Visual alarm indication by built-in LED indicators: burglary/24-hour/tamper alarm and re alarm indicated in dierent colours.
• 2 tamper switches: for enclosure opening and device detachment from the wall detection.
EWS3 is a wireless indoor device with built-in siren speakers and LED indicators operating with ELDES wireless alarm systems. The de-
vice is designed to notify the user by audio and visual signals in the event of alarm as well as in event of system arming/disarming (Bell
Squawk feature must be enabled). In the event of burglary, 24-hour or tamper alarm, EWS3 will activate the speakers and ash the blue
LED indicators, while in case of a re alarm, the device can ash the red LED indicator (both features require EWS3 Alarm LED and EWS3
Fire Alarm LED parameters to be enabled using ELDES Conguration Tool software or EKB2/EKB3/EKB3W keypad)
To start using EWS3, it has to be bind to ELDES alarm system by sending a corresponding SMS message or using software ELDES Cong-
uration Tool. Upon successful EWS3 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm,
the siren provides a sound alarm for one minute. The conguration of this parameter is disabled for EWS3 in order to save the battery
power.
ESIM264 and EPIR2 alarm systems support up to 16 EWS3 devices, while ESIM364 - up to 32 EWS3 devices. The maximum wireless con-
nection range is 150 meters (in open areas).
1. CONTENTS OF PACK
1. EWS3...................................... .................. qty. 1
2. 1,5V Alkaline AA Type Battery.......... ... qty. 4
3. User Manual... ............. ...........................qty. 1
4. Screws... ...................... ...........................qty. 2
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Battery type ...........................................................................................1,5V Alkaline AA type
Number of batteries .............................................................................4
Battery operation time .........................................................................~18 months*
Wireless transmitter-receiver frequency .........................................868 Mhz
Range of operating temperatures .....................................................-25...+55ºC
Humidity .................................................................................................0-90% RH @ 0... +40 °C (non-condensing)
Dimensions .............................................................................................167 x 80 x 34 mm
Wirelesscommunication range ...........................................................Up to 30 meters in premises; up to 150 meters in open areas
Compatible with alarm systems ..........................................................ELDES Wireless
* The operation time might vary in dierent conditions.

3
3
EN
EWS3 – Wireless Indoor Siren
2.2. Main Unit, LED & Connector Functionality
FRONT SIDE of PCB BACK SIDE of PCB
BUZZER
BUZZER
RESET
STATUS
ALARM (blue)
ALARM (blue)
ALARM (red)
TAMPER
TAMPER
BATTERY +
BATTERY
+ -
-
-BATTERY +
-BATTERY +
1
RESET Button for restoring default parameters
+ / - Battery slots
STATUS LED indicator for data transmission indication
ALARM (blue) Blue LED indicators for visual alarm indication
ALARM (red) Red LED indicator for visual alarm indication
BUZZER Speakers for audio alarm indication
TAMPER Tamper switches
FRONT SIDE of ENCLOSURE
ALARM (blue)
ALARM (blue)
ALARM (red)
2
LED indication Description
ALARM (blue) ashing Burglary, 24-Hour or tamper alarm in progress
ALARM (red) ashing Fire alarm in progress

4
4
EN EWS3 – Wireless Indoor Siren
3.INSTALLATION
1. Open EWS3 enclosure.
a. Press and hold
b. Pull down
3
2. Once the enclosure is opened, x the siren to the wall using the screws.
+
+ -
-
- +
- +
MOUNTING POINT AMOUNTING POINT B MOUNTING POINT A
Ensure to screw in properly for supervision of the back side by tamper switch
MOUNTING
POINT B
4 5
3. When installing EWS3, follow the recommendations for the installation to achieve the strongest wireless signal:
Wireless
device
6
Never install in the following
locations:
• inside the metal cabinet
• closer than 20 cm from
the metal surface and/or
power lines
Wireless
device
5 m to 30 m
inside the building
0.5 m to 150 m
in open areas
ELDES alarm
system wireless
antenna
7
Recommended:
• face the front side of the
wireless device towards
ELDES alarm system’s wire-
less antenna
• keep the distance: 0.5 m to
30 m inside the building, 0.5
m to 150 m in open areas.
EPIR2
Wireless
device
0.5 m to 30 m
inside the building
0.5 m to 150 m
in open areas
8
Recommended:
• face the front side of the
wireless device towards
the front side of EPIR2
• keep the distance: 0.5 m to
30 m inside the building,
0.5 m to 150 m in open
areas.
4. Remove the plastic tab inserted between one of the battery terminals and battery slot contacts.
9
5. STATUS indicator should start ashing indicating successful data transmission.

5
5
EN
EWS3 – Wireless Indoor Siren
6. Close EWS3 enclosure by putting the cover back (see Fig. No. 3).
7. Bind the device to the alarm system using ELDES Conguration Tool software. Open Wireless Device Management section and
enter a 8-digit wireless device ID located on the EWS3 enclosure and press Add button (see Fig. No.10). The device can also be bind by
sending a corresponding command via SMS message. For more details, please refer to the software‘s HELP section and ELDES alarm
system installation manual.
10
8. Upon the successful binding process, EWS3 device icon becomes visible in Wireless Device Management section as well as Battery
Level and Signal Level. If attempt to bind is unsuccessful, try to move EWS3 closer to the alarm system device and bind anew.
9. EWS3 siren is ready for use.
ATTENTION: Ensure that EWS3 device is properly xed to the wall and the Mounting Point A portrayed in Fig. No. 4 and Fig. No. 5 is properly
screwed in. Otherwise, the tamper switch will NOT supervise the back side of EWS3 enclosure (see also 4. EWS3 ZONE, PGM OUTPUT
AND TAMPER).
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again.
See chapter 6. RESTORING DEFAULT PARAMETERS for more details.

6
6
EN EWS3 – Wireless Indoor Siren
4.EWS3 ZONE, PGM OUTPUT AND TAMPER
Upon successful EWS3 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The
wireless zone is intended for EWS3 tamper control and ability to assign a partition (-s), while the wireless PGM output is intended for siren
speaker control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper viola-
tion on EWS3:
• By tamper switch. EWS3 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
• one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 1).
• the other one located on back of the PCB supervising the back side of the enclosure in case the EWS3 is illegally detached from the
wall (see Fig. No. 1).
Once the enclosure of EWS3 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS3 and ELDES alarm system leads to alarm. The system
identies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
5.BATTERY REPLACEMENT
1. Open EWS3 enclosure.
2. Remove all 4 old batteries from the battery slots.
3. Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated
on the PCB (printed-circuit-board) of EWS3
4. Insert the batteries into the battery slots.
5. Batteries replaced.
See chapter 3. INSTALLATION for more details.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the
old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid re or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Conguration Tool software.
6.RESTORING DEFAULT PARAMETERS
1. Remove one battery from EWS3.
2. Press and hold the RESET button.
3. Insert the battery back to EWS3.
4. Hold the RESET button until LED indicator starts blinking.
5. Release the RESET button.
6. Parameters reset to default.

7
7
EN
EWS3 – Wireless Indoor Siren
7.ADDITIONAL INFORMATION
Limited Liability
The buyer must agree that the system will reduce the risk of re, theft, burglary or other dangers but does not guarantee against such
events.“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system. “ELDES UAB”
liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not aliated with any of the Internet
providers therefore is not responsible for the quality of Internet service.
Manufacturer Warranty
This device carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been
purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the
manual and within specied operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided if the system
has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environment or other force majeure
factors.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further infor-
mation on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.