Display Mount Pro MDM 003T User manual

English
Installation Instruction
1
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure
that all components were received undamaged. Do not use damaged or defective
parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
! Install and operate this device with care. Please read this instruction before
installation, and carefully follow all instructions contained herein. Use proper safety
equipment during installation.
! Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaims any and all liability for injury or damage arising
from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Par ts List
2
(1) Swivel Arm-d1
(1) “C” Clamp-b (1) “C” Clamp Brace-c
(1)Support Plate-j(1)M10 Bolt-i (1)M10 Washer-k (1)Spring Washer-l
(12)M4 Spacer-s
(12)M4x12
Thumb Bolt-q (12)M4x30 Bolt-r
(1) Grommet Base
Plate-m (2)Wire Clip-n1 (1)Allen Key-o
(1)Wrench-p
(4)Wire Clip-n2
(2) VESA Plate-e1
(3) M5x14 Bolt-g (2) M8x12 Bolt-h(2) Nut-f1
(1) Monitor Arm-d2 (1)VESA Plate-e2
(1)M4x6 Bolt-f2
(1) Lower Pole-a1 (1) Upper Pole-a2

Pre-Assembly
3
a1
a2

Step 1 Install the Pole to the Desktop
4
Option B: Grommet Base Install
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(g), and
tighten using the Allen Key(o), see Figure 3.
2. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 4.
a
Figure 3
m
g
Figure 4
j
i
k
l
Existing Grommet Hole Installation
Option A: Desk Clamp Install a
1. Install the “C”-Clamp Brace(c) to the Pole
(a) using 3pcs M5x14 Bolts(g), and tighten
using the Allen Key(o), see Figure 1.
2. Install the “C”-Clamp(b) to the pole
assembly according to the thickness of the
desktop. The thickness can be changed to
three positions. Connect it using 2pcs M8x12
Bolts(h), and tighten using the Allen Key(o).
Tighten the “C”-Clamp to the desktop using
the plastic knob, see Figure 2.
Figure 1
c
g
Figure 2
h
o
b
Plastic Knob

Step 1 Install the Pole to the Desktop
5
Self Drilled Grommet Hole Installation
Option B: Grommet Base Install
1. Position the Pole(a) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked position
through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(g), and
tighten using the Allen Key(o), see Figure 5.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 6.
a
Figure 5
m
g
Figure 6
j
i
k
l
Step 2 Install Arm to the Pole
d1
o
Install Swivel Arm(d1,d2) to the
Pole(a). Fasten the bolt with
supplied Allen Key(o). Attach
the Wire Clip(n1,n2) to the
Pole(a) and Swivel Arm(d1).
n1
n2
d2

6
Step 3A Attach the Side VESA Plates to the Monitors
For Monitor with Curved or
Recessed Back
For Monitor with Flat Back
qs
r
Step 3B Attach the Center VESA Plate to the Monitor
For Monitor with Flat Back
q
For Monitor with Curved or
Recessed Back
s
r
e1
e1
e2 e2

7
Step 4A Slide the Side Monitors onto the Head of Swivel Arm
Install the security Nut(f1). Make
sure the security nut is installed
before you rotate the monitor.
Slide the monitor onto the head of
Swivel Arm(d1) as shown in the
above diagram.
f1
Step 4B Slide the Center Monitor onto the Head of Monitor Arm
Install the M4x6 Bolt(f2). Make
sure the bolt is installed before you
rotate the monitor.
Slide the monitor onto the head of
Monitor Arm(d2) as shown in the
above diagram.
f2
d1
d2

Step 6 Adjust the Level of Monitors and Manage the Wires
Step 5 Fix the Tilt Angle of Side and Center Monitors
8
o
Tighten the bolt with the supplied Allen
Key(o) to fix the tilt angle.
Fix the tilt angle
Thank you for choosing our products!
If one monitor is lower, remove the Nut(f1)
and turn the bolt counter-clockwise with
supplied Allen key(o) to raise the monitor.
Install the Nut(f1) after the adjustment.
Manage the wires and store the Allen
keys(o) in Wire Clip(n1) for future use.
n1
Ignore this step if
monitors are level
o
Fasten the grub screw in monitor arm to fix
the tilting angle by provided Allen Key(o).
grub
screw
Fix the tilt angle