Divine Lighting Hyper 361 P User manual

Hyper 361 P
USER MANUAL

Summary .......................................................................................................................1
Safety Instructions ........................................................................................................1
Product Dimensions ......................................................................................................2
Main Functions..............................................................................................................3
DMX Operation.............................................................................................................4
Display Operation Instruction.....................................................................................5
Manual Instructions......................................................................................................5
Master/Slave Operation................................................................................................7
XLR Connection............................................................................................................7
Wiring Diagram.............................................................................................................9
Troubleshooting........................................................................................................... 11
Technical Specifications……………………………………………………………..13
Please read over this manual before operating the light
Index

www.divinelighting.com
1Hyper 361 P v1.0
1. Summary
Thank you for purchasing our Hyper 361 P lighting fixture. Please read these
instructions carefully prior to operation. Use the fixture according to these instructions to
reduce the chance of damage and accident.
Product Introduction
This product uses high power R, G, B LED diodes. Each color can be manipulated
independently. It can be operated via built-in programs or by international standard DMX
512 signal.
Packing list
Hyper 361 P Light 1pc
DMX cable 1 pc
User manual 1pc
2. Safety Information
Safety Notes
! Repairs should be attempted only by qualified professionals;
! Always make sure disconnect from the power source before setting up, servicing and moving;.
! Avoid direct eye exposure to the LED output when it is on;
Safety Instructions
● Make sure the power supply voltage is consistent with the requirements of this fixture.
●Before the installation, please ensure that the light’s fasteners and mechanical
structure have been received in good condition and there is no damage.
● This light is designed for indoor use only. Ambient temperature should not exceed 40
degrees Celsius.
●This fixture maybe mounted in any position provided there is adequate room for
ventilation. Make sure there are no inflammable and explosive items within 0.5 meters

www.divinelighting.com
2Hyper 361 P v1.0
of any surface of this unit.
●Please make sure that this fixture is properly grounded.
3. Dimensions

www.divinelighting.com
3Hyper 361 P v1.0
4. Main Functions
 High quality LED's: low power consumption, high brightness, stable output and long
lifetime.
Each color of LED dims in 256 increments.
Combined, RGB yields over 16.7 million colors combinations.
36 one-watt LED’s of light: 12 Red, 12 Green, 12 Blue
Linear Dimming 0%-100%, Strobes, Color change by fading, Color change by snapping
Modes: Auto run /sound activated/master slave/DMX remote controlled
Using switching power supply for optimal functioning and light weight.
DMX512 channels: 6 channels
Cast aluminum casing: Black, White (optional)

www.divinelighting.com
4Hyper 361 P v1.0
5. DMX Control Function
DMX
Channel
DMX Value
Control
Function
Remark
Priority
1
0-255
Master Dimmer
0——100%
0 = Off
255 = Full On
1
2
0-255
Red Dimming
0——100%
0 = Off
255 = Full On
3
0-255
Green Diming
0——100%
0 = Off
255 = Full On
4
0-255
Blue Dimming
0——100%
0 = Off
255 = Full On
5
0-14
Dimming
When Channel 6 is 32-223，this
channel adjusts the speed of the
selected function (0-255)
2
15-255
Strobe Speed
Increasing Strobe Frequency
6
0-31
Invalid
Use 0-31 when you wish to only
use Channels 1-5.
32-63
From dark to
bright
Must use Channels 1-4, otherwise
no light，Adjust speed with
Channel 5.
3
64-95
From bright to
dark
96-127
From dark—
bright—dark
128-159
RGB Gradient
Adjust speed with Channel 5..
Channels 1-4 disabled.
160-191
3 colors snap
change
192-223
7 colors snap
change
224-255
Sound
activated.
Fixture changes color to noises.

www.divinelighting.com
5Hyper 361 P v1.0
6. Display Operation
DMX IN/OUT
LED Display
4 Buttons
MENU : access the menu or return to a previous menu option
ENTER: select the current menu option
UP: menu selection or parameter increase
DOWN: menu selection or parameters decrease
7. Manual Instructions
Operating instructions:
1. The MENU button is used initially to access the menu. After that, it is used to return to
a previous menu. Pressing UP / DOWN cycles through the available options at that
menu level.
2. Press ENTER to access the displayed menu setting. If you are at the end of the menu
tree and press enter, then that value displayed will be saved, even when the unit has
been powered off. For example, if you want to set the DMX channel to 1, operate as
follows:
a) Press MENU, go back to the initial setting
DMX IN DMX OUT
MENU ENTER UP DOWN

www.divinelighting.com
6Hyper 361 P v1.0
b) Press UP / DOWN until ―Addr‖ is displayed
c) Press ENTER to select address adjustment
d) Press UP / DOWN to change the address code to select A001
e) Press ENTER to select and store the current address. DMX mode will be stored
automatically and the screen will stop flashing.
3. Primary Menu Options :
a) ‖addr‖: DMX mode – The unit is remotely controlled by a DMX controller set to the
same address as this fixture. The possible addresses range from 1-512 and are
displayed as A001, A002, ….A512.
b) ―SouF‖: Sound mode –Light flashes to sounds.
c) ―SouA‖: Sound mode –Light changes colors to sounds.
d) ‖SP‖; built-in program color cycles (SP00-SP15, SP00 is the fastest)
e) ‖Pr‖; Built-in programs （Pr00-Pr15: 16 programs in all）These programs are listed
below. Pr7-Pr15 have adjustable speeds Sp0-Sp15. (Sp15 is the fastest.)
Pr00 = red
Pr08 = strobing green
Pr01 = green
Pr09 = strobing blue
Pr02 = blue
Pr10 = strobing amber
Pr03 = amber
Pr11 = strobing cyan
Pr04 = cyan
Pr12 = strobing purple
Pr05 = purple
Pr13 = strobing white
Pr06 = white
Pr14 = three color cycle (RGB)
Pr07 = strobing red
Pr15 = seven color cycle
f) ‖ASC‖; seven color cycle（AS00-AS15 speed adjustable）
g) ‖FAdE‖: gradual change between colors（FA00-FA15 speed adjustable）
h) ‖FLAS‖: (as in Flash) white color strobe（FL00-FL15 speed adjustable）
i) ‖rL‖: red color brightness adjustment mode （r000-W255, r255 is the brightest）
j) ‖gL‖: green color brightness adjustment mode（g000- g255, g255 is the brightest）
k) ‖bL‖: blue color brightness adjustment mode（b000- b255, b255 is the brightest）

www.divinelighting.com
7Hyper 361 P v1.0
Adjusting built-in programs（Pr- -）
1. Press MENU to go back to the initial setting
2. Press UP / DOWN until Pr—
3. Press ENTER to choose, the display will flash at this moment
4. Press UP / DOWN to find the desired program number
5. Press ENTER to select and store the current menu options. The unit will retain
this setting even after the power has been cycled.
8. Master/Slave Operation
Master/Slave: All of the units are connected together so that the output of the
first (Master) are mirrored in all of the other units (Slaves)
Master：Units are always set in Master mode (i.e. outputting DMX signal that mirrors
their own operation) unless they are set in DMX (which is also Slave mode). Signal lines
longer than 60 meters or 20 fixtures should utilize a signal amplifier.
Slave：Connect all the slave units to the master unit using DMX cable. Set all slaves
to DMX mode and address them to channel 1 (A001). Any adjustments made to the master
should be displayed on the slaves as well.
9. XLR Cable Connections
XLR cable：(DMX Cable)
XLR/DMX connections are connected male to female, as shown below:
pin 1:ground,pin 2: negative signal, pin 3: positive signal

www.divinelighting.com
8Hyper 361 P v1.0
Note : Male and female jacks are wired in parallel. Either may be used for input and
output.
Note：In order to avoid failures and interference with signal transmission，use a
terminator plug. Between pins 2 and 3, connect a resistance120Ω（1/4W）at the end
of the DMX connecting as below:
Conversion between 3-pin and 5-pin XLR
If the output cable of DMX 512 controller is the 5-PIN, please use a 5-PIN to 3-PIN
adapter.

www.divinelighting.com
9Hyper 361 P v1.0
10. Connection Diagram

www.divinelighting.com
10 Hyper 361 P v1.0
Electrical wiring diagram
显示板
display board
DC 24V IN
16P computer cable
DMX IN
LED Aluminum Light Panel
灯板连接线
DSLM-PAR575-5A
K1
K2
K3
K4
V+ V+ R G B
GND
POWER IN DISPLAY
DMX IN/OUT UR UB
1 Control board
2 DSLM-PAR575-5408
3 UG UW
STC12C5404
34063
75176
LM358
MIC
C1
L1

www.divinelighting.com
11 Hyper 361 P v1.0
11. Troubleshooting
Note：Only qualified professionals should attempt to service this unit!
Problem
Possible Solution/Cause
Can not turn on the
light
Ensure the power plug is fully inserted
Ensure the power switch for the lights is on
Check the fuse continuity
DMX not functioning
Check the DMX cable is connect to the lights
Check the DMX512 controller for signal output
Check if the lights is in DMX mode（A001）
Display not bright
When initially powered，did the led flash one time? If so，the
power source is normal. If not, please check voltage switch or
voltage supply.
Check if the power input to the IC board is normal
Check if the cable connect to the display is loose
Change the main board to see if it is normal.
Change the display
LED's not coming on.
When connect to the electricity，did the led flash one time? If
so，the power source is normal. If not, please check voltage
switch or voltage supply.
Check if the power input of the IC board is normal
Check if the cable connect to the display loose
Change the main board to see if it is normal.
Change the display
Some of the LED's
not coming on.
LED is connect in series first, then in parallel. Check to see if
any LED's are loose.
Use the multimeter to check if the led is powered or not. If not,
please change the led.
Check whether current limiting resistor is normal or not
Check constant current IC is normal or not (compared with the

www.divinelighting.com
12 Hyper 361 P v1.0
normal IC)
Single color LED's
Always bright/not
bright
Check the switch of this color is normal or not
Change the IC control board

www.divinelighting.com
13 Hyper 361 P v1.0
12. Technical Specifications
●Input voltage：AC 100V-264V/47-63HZ
●Power Consumption：50 Watts
●Lamp Type：High Power LED (1W)
●Lamp Spec：Red（12 PCS), Green（12 PCS), Blue（12 PCS）
●Life span: 50000-100000 hours
●Control mode：stand alone, master, slave, DMX, sound active
●Channel：6CH
●Color Effect: RGB Mixing
●Beam Angle: 25°,(15° or 45° by special order)
●Display mode：4 seven-segment LED screen display, four-key input
●Cooling mode: Natural Convection
●Anti-electricity intension：1.5KV
●Insulation Resistance：＞２MΩ
●Size:：330*295*220mm
●Net Weight：5 KG
●Casing: Cast Aluminum Black (White by special order)