dji Osmo Z-Axis User manual

Quick Start Guide
OSMO Z-Axis
V1.0
2016.04

Disclaimer and Warning
Congratulations on purchasing your new DJITM product. The information in
this document affects your safety and your legal rights and responsibilities.
Read this entire document carefully to ensure proper conguration before
use. Failure to read and follow instructions and warnings in this document
may result in serious injury to yourself or others, damage to your DJI
product, or damage to other objects in the vicinity. This document and all
other collateral documents are subject to change at the sole discretion of
DJI. For up-to-date product information, visit http://www.dji.com and click on
the product page for this product.
By using this product, you hereby signify that you have read this disclaimer
and warning carefully and that you understand and agree to abide by the
terms and conditions herein. You agree that you are solely responsible
for your own conduct while using this product, and for any consequences
thereof. You agree to use this product only for purposes that are proper and
in accordance with all applicable laws, rules, and regulations, and all terms,
precautions, practices, policies and guidelines DJI has made and may
make available.
DJI accepts no liability for damage, injury or any legal responsibility
incurred directly or indirectly from the use of this product. The user shall
observe safe and lawful practices including, but not limited to, those set
forth in this document.
1

Introduction
The OsmoTM Z-Axis can signicantly reduce vertical shaking from natural
arm movements when walking or jogging. It is compatible with the
ZenmuseTM X3 gimbal and camera.
[1] Gimbal Securing Ring
[2] Arm
[3] Pivot Release Button
[4] DJI Rosette Mount
[5] Securing Knob
[6] Handle Connector
[7] Tension Adjustment Knob
The Z-Axis is NOT intended for action sports that involve extreme
movement or to be used with other non-DJI devices.
Specications
Weight: 282 g
Dimensions: 212 mm x 67 mm x 127 mm
[1]
[2]
[3]
[4]
[5]
[6]
[7]
2

Installation
1. Rotate the Osmo handle’s gimbal securing ring to its unlocked position.
2. Insert the Z-Axis’s handle connector into the gimbal securing ring.
3. Lock the gimbal securing ring.
4. Screw the Z-Axis’s securing knob to the Rosette Mount on the side of the
Osmo handle. Ensure that it is mounted securely.
3

5. Rotate the Z-Axis’s gimbal securing ring to its unlocked position and
attach the Zenmuse X3.
6. Lock the gimbal securing ring. Ensure that the Zenmuse X3 is mounted
securely.
Adjusting the Balance
The balance of the Z-Axis should be adjusted to ensure that the arm can
move up and down freely without bumping against the endpoints.
4

Place the Osmo on a at and stable surface so that it is perfectly upright.
Adjust the height of the arm by turning the tension adjustment knob. The
arm should be elevated slightly above the horizontal plane as shown.
Avoid icking your wrist when lming. Move your arm steadily while
keeping the gimbal upright.
Keep ngers, hair and small objects away from the arm during use
so they do not get caught in the articulating mechanism.
5
Horizontal Line

DO NOT attempt to adjust the grip angle without pressing the pivot
release button as this will damage the Z-Axis.
Adjusting the Grip Angle
While holding down the pivot release button on the Z-Axis, rotate the Osmo
handle vertically to the desired position, and then release the button to lock
that position.
6

The content in this document is subject to change.
Download the latest version from
www.dji.com/product/osmo
If you have any questions about this document, please contact DJI
by sending a message to [email protected].
© 2016 DJI. All Rights Reserved.
DJI Support:
www.dji.com/support