DLS RW15 User manual

REFERENCE SERIES
SUBWOOFERS
WELCOME
Thank you for buying a DLS REFERENCE subwoofer.
Thesubwoofermustbeinstalledcorrectlyinordertowork
well. This manual will show you how to install it like a pro.
Please read the entire manual before beginning the in-
stallation.
Install the subwoofer yourself if you feel confident with
ourinstructionsandifyouhavethepropertools. However
ifyoufeelunsure,turnovertheinstallationjobto someone
better suited to it.
The speakers are designed for enclosure mounting. In
"open air" installations the power handling capacity is
reduced by 30% from the nominal value.
CONNECTION OF SUBWOOFER
How to connect depends on what type of amplifier you
use. The best is to follow the instructions given in the
manual for the amplifier. Most amplifiers today have built-
in lowpass crossover and possibilities to connect your
subwoofer in bridge mode.
Two4ohm subwoofersare oftenconnected instereomode
since most amplifiers can´t handle bridge mode loads
below 4 ohms. If you have a DLS Ultimate amplifier it´s
possibleto connect two 4 ohm subs in bridge mode, these
ampliers are 1 ohm stable.
RW15 has double four ohm voice coils which makes the
subwoofer more flexibl. You can connect a single voice
coil in 4 ohm. If you want to use both voice coils you can
either connect them in series to 8 ohm or in parallell to 2
ohm. If you want to connect more than one subwoofer
the dual voice coils system gives you great possibilities
to connect in a way that suits your amplifier.
We also recommend the use of a subsonic highpass fil-
ter. This gives a better bass reproduction with less
"rumble". In most DLS amplifiers this feature is already
built-in.
For wiring use high class speaker wires, minAWG13 (2.5
mm2). For example DLS SC 2x2,5.
RW15
SUBWOOFER ENCLOSURES, GENERAL
Build your enclosure in a stable and airtight material. The
best is MDF-board, 19 mm, or particle board, 22 mm.
Larger enclosures must have bracing inside to avoid
vibrations.Theenclosuremustbe completely airtight. Use
sealing compound in all joints, also around the cable
terminals.Thesizeoftheenclosureis decidedbythe spea-
ker data.
SEALED ENCLOSURES
Sealedenclosuresareeasy tobuild.Thesize is notcritical,
but it can´t be too small. The speaker data such as Fs,
Qts, Vas and X-max decides the size of the enclosure.
Large speakers need larger boxes.Two speakers need a
box of the double size etc. The enclosure must be
completely airtight.
A sealed enclosure should be filled with acoustic wool up
to 75 - 100%.
A sealed enclosure has a lower efficiency than vented
enclosures but they can handle high power and are easy
to build. A subwoofer in a sealed enclosure creates a
tightbasssuitablefortheaudiophileslisteningto classical
music, jazz and soft rock. You can use RW15 in sealed
enclosures if you use single voice coil connection.
VENTED ENCLOSURES
Aspeakerinaventedenclosure has a higher efficiency(3
dB) and higher power handling capacity than in a sealed
enclosure.In a vented enclosurethesoundfrom the spea-
ker and the port work together creating a higher sound
level.The sound from the port mustcome out in the same
phase as from the speaker otherwise the result is bad.
The size of the vented enclosure is decided by the spea-
ker data just as for the sealed one.
The size of the vehicle often decides the practical size of
the enclosure.Asmaller enclosure has a higher resonant
frequency than the larger one. The size of the enclosure
shouldnotbeso big that the speaker plays below it´s own
free air resonance (Fs), then it looses in power handling
capacity.
The port does not have to be fully inside the enclosure as
long as the area and length are correct.
Sometimes you need two or more ports in an enclosure.
You can convert from one to two or more ports as long as
the total port area is the same.
All DLS subwoofers works well in vented boxes.
BANDPASS ENCLOSURES
In all bandpass enclosures the speakers are hidden in-
side the enclosure, all sound is coming out through the
ports. There are different types of bandpass enclosures
and they have in common that they are a bit more difficult
to build. Most DLS subwoofers can be used in bandpass
enclosures.
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
www.dls.se
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.

RW15
Size 37,5 cm (15")
Impedance Z 2 x4 ohm
Nom.power (RMS) 400 W (max 600)
Frequency range 15 Hz - 1 kHz
Voice coil diameter 75 mm (3”)
Voice coil length 40 mm (1,57”)
X-max +-14 mm (0,55”)
CMES 117,8421
SD 830 cm2
Cone material Paper
Magnet, weight 160 oz (4,5 kg)
Magnet, diameter 180mm (7,08”)
Installation depth 180 mm (7,08”)
Mounting hole 353 mm (13,9”)
Outer diameter 385 mm ( 15,15”)
Weight 12,5 kg (27,55 lb)
Data that varies depending on way of connection:
Single VC, 4 ohm VC:s in series to 8 ohm VC:s in parallel to2 ohm
Re / Z 3,6 ohm / 4 ohm 7,1 ohm / 8 ohm 1,6 ohm / 2 ohm
BL product 13,3 25,6 13,2
Sensitivity 86,7 dB 89,4 dB 90,1 dB
Fs 29,4 Hz 28,7 Hz 28,7 Hz
Vas (liter) 116,3 122,2 122,2
Vas (ft3) 4,1 4,3 4,3
Qms 3,2 3,2 3,2
Qes 0,75 0,42 0,38
Qts 0,75 0,43 0,30
TECHNICAL SPECIFICATIONS FOR DLS REFERENCE SUBWOOFERS
RECOMMENDED ENCLOSURES FOR RW15
VENTED ENCLOSURE
SEALED ENCLOSURE
The speaker is installed in Vb1
playing into chamber Vb2 where
the port(s) are installed.
F3 = approximative lower frequency for
vented boxes in Hz. Often called F-3 dB point
= the point where the power is 50% lower.
Fb = Box resonant frequency
SEALED BANDPASS
Vb1=rear chamber
Vb2=front chamber
RUNNING-IN PERIOD
Allow the speaker to play for at least
15-20 hours.After this time the
performance is correct.
B
H
ÖD
ND
CALCULATE YOUR ENCLOSURE
Box volumes:
Whencaculating thevolumeof an enclosureyousimply
multiply the width (W) x heigth (H) x depth (D).
Use measures in dm and you will get the answer in
liters.
A trapezoid box is calulated as below:
Vol=width (W) x heigth (H) x upper depth (UD) + lower depth (LD)
2
upper
suspension
voice coil pole plate
magnet
spider
chassis dust cap
speaker cone
T-yoke
Be sure to measure the
inside dimensions.
Subwoofer Volume (liter/ft3) Port Dampning F3 Fb
RW15* vol: 46 / 1,62 4” x 27 cm/ 10,6” Line inside 44,4 Hz 40 Hz
RW15** vol: 56 / 1,98 4” x 29 cm/ 11,4” Line inside 38,7 Hz 35 Hz
*=voice coils in parallel to 2 ohms. **=voice coils in series to 8 ohms.
RW15
Vb1 Vb2 port Vb2
29,78 26,76 2x10,2x44 cm
1,05 ft30,94 ft32x4"x17" (US)
F3 Vb1: 40 Hz, Vb2: 109 Hz
In this example the voice coils
are connecten in parallel to 2
ohms.
Sealed enclosure:
Volume 58 liters
F3= 38,5 Hz
Use single voice coil 4 ohm