DLS CRUISE CRPP-UW64 User manual

User manual
Universal 4 ohm woofer

Content
Welcome
Warranty
General
Declaration of conformity
Included parts
Pre installation
Installation
Running-in time
DLS support
Wiring diagram
Specifications
Dimensions
Impedance vs Frequency
Product markings
1
1
1
1
2
2
2
3
3
4
5
5
5
6
DECLARATION OF CONFORMITY
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-UW64. For us,
it’s all about the sound experience. We care deeply about
sound and construction quality. In order for your experience
to be as optimal as possible, it is important that you read
this manual, preferably before you start your installation.
Keep the manual in a safe and accessible place for future
reference.
Your speakers must be installed correctly in order to work
as intended. Make sure you have all necessary tools nearby
before starting and that you are completely confident in how
to process. If you feel the slightest uncertainty; feel free to
take the help of an experienced installer or a car audio
dealer.
General
Some sound systems may vary in size of the door speaker.
Make sure that your vehicle has the same size as this
speaker, before you start the assembly
DLS Cruise speakers for vehicles are manufactu-
red in accordance with the EU directive EEC 95/54
(72/245/ EEC) and are marked with the approval
number. They are also marked in accordance with
the WEEE-directive 2012/19/EC. The products are
also produced in accordance with the EU RoHS
directive 2015/863/EU.
Warranty
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
Winn Scandinavia AB
Elementvägen 15 - SE-702 27 Örebro - Sweden
Tel: [phone] - E-mail: [email protected]
www.dls.se
DLS speakers are engineered by DLS Sweden,
a part of:
Designed & Sound tuned in Sweden.
CRPP-UW62
DLS CRUISE

2
Pre installation
Disconnect Battery
Before you start the process
of replacing speakers,
disconnect and secure the
negative terminal from your
battery/power source. This
will prevent the risk of
damaging yourself or the
products.
Place the disconnected terminal in a secure and
isolated location away from any possible
connection belonging to the battery/power source
system. Speaker connection
Make sure you connect the cables with correct
polarity on the speaker terminals. Observe the
markings and size differences on the connectors.
Included products:
2pcs Woofers
Included in box:
8pcs M4 screws
4pcs Fork terminals
4pcs Flat pin connectors
1pc PRY tool
1pc Manual
Included parts
Installation
Mount the speakers in the door or in the rear shelf
of your car. They may fit in the factory pre-made
mounting holes, if not you might have to modify
the fitting. If you want to improve the sound
reinforcement you can use a baffle of MDF-board
or similar. For door placements, there are normally
speaker rings that have to be used to make the
speaker fit to the door panel.
NOTE! It is important to fasten the speakers
properly in order to avoid bad sound or rattling.
General installation
Custom baffle installation
It is very important that the custom baffle are
stable and fasten properly, but it is just as
important that it´s shaped in a way that the driver
is allowed to “breathe” correctly. Bass reproduc-
tion will be enhanced when the air flow is free and
not obstructed.
Wrong way
Correct way
with chamfer-
ed edges
Max 5 mm
Correct way
Speaker phasing
To be sure that the CRPP-UW64 woofer are using
the correct polarity (phase) after installation, it is
possible to check this easily by using a 1.5 volt
battery.
Connect the battery’s positive and negative pole
to the speaker cable. If the speaker is correctly
connected the cone should move outwards. This
need to be tested on all left/ right pairs to make
sure all drivers are in phase with each other.
Note!
Don´t use this testing method on tweeters or
other low excursion drivers without a correct
connected high pass crossover.

DLS recommend using active crossover settings
for the UW64 speaker to get increased power
handling and durability.
High pass filter: 60-100 Hz
Low pass filter: 3500-5000Hz
Crossover settings
DLS recommends using insulation and/or sound
deadening in the car doors. It lowers the noise
from the road/tires and prevent rattles and other
noises from plastic details in the doors.
If you need help deciding what type of door
insulation you should use, ask your DLS
distributor for info and guidance.
Door insulation
DLS support
For technical assistance, ask your car audio
dealer where the product was sold or the dis-
tributor in your country. You can always contact
DLS Helpdesk in Sweden at e-mail: [email protected].
Information can also be found on our WEB-site
www.dls.se. We follow a policy of continuous
advancement in development. For this reason, all
or part of specifications and designs may be
changed without prior notice.
Running-in time
Allow the tweeters to play for at least 15-20 hours
in order to perform at its possibly best.This run-in
can be made with tone sweep or with just music.
Start at a moderate
volume and increase
the volume step by step
during the running in
period. After the 15-20
hour run in session the
performance and char-
acteristics will be in the
correct condition.
3

4
Wiring diagram

Specifications
Art. no CD-CRPP-UW64
Impedance VS Frequency
5
90mm
166mm
59mm
124mm 156.5mm
Dimensions
Woofer 6.5” / 165mm
RMS Power 100W
MAX Power 200W
Impedance 4 Ohm
Sensitivity 86.8dB 1W/1M
Freq. range 55-5000Hz
Technical specifications
Voice coil size 1” / 25mm
Voice coil material Copper voice coil / Kapton® former
Basket Euro-DIN ventilated reinforced steel frame
Magnet High grade ferrite / Ventilated back plate
Cone Laminated glass fibre cone
Dust cap Santoprene® rubber dust cap
Spider Nomex® with woven tinsel leads
Terminal Twin terminal
Electro-Acoustic Parameters
Re 3.2 Ohm
Fs 63.2Hz
Mms 15.8gr
Cms 0.399
Vas 10.9L
Qts 0.66
Qes 0.89
Qms 2.512
Bl 4.74T.m
SPL 86.8dB 1W/1M
Sd 139cm
20 Hz 50 100 200 500 1K 2K 5K 10K
2
5
10
20

This product has been granted with the CE certification mark to show that the
product follows the health, safety, and environmental protection standards for
products sold within the European Economic Area (EEA).
DLS products complies with the relevant provisions of the RoHS
Directive for the European Union. In common with all Electrical
and Electronic Equipment (EEE) the product should not be
disposed of as household waste. Alternative arrangements may
apply in other jurisdictions.
aideMeliboMnaeporuEehtforentraplabolgasiSLD
Association, an organisation that focus on promoting the
custom made mobile media installations to consumers.
Product markings
We follow a policy of continuous advancement in development. For this reason all or part of
specifications & designs may be changed without prior notice. We reserve for possible typos,
factual or numeric errors that may have been printed on any products, package designs,
user manuals and/or other included accessories.
6
The crossed-out wheelie bin symbol means that the product, literature and
packaging included must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste:
take them for recycling. For info on your nearest recycling point, check with
your local waste authority.