DMP Electronics SR3 User manual

SR3 Bluetooth and Proximity Reader
Quick Start Guide
Wire the Reader
WARNING: Do not press and hold the button on the back of the reader. This procedure clears the unit’s memory
and firmware, which renders the device inoperable until it is reconfigured and re-enrolled.
Disconnect power before wiring the reader. After wiring and reconnecting power, the LED turns steady yellow, indicating
that the reader is ready for enrollment. Follow these guidelines when wiring the reader: Connections must be made in
accordance with NFPA 70: Do not connect to a receptacle controlled by a switch. Minimum wire gauge is 24 AWG with a
maximum single wire run length of 500 ft (150 m).
SR3 Installation and Programming Guide | Digital Monitoring Products 3
Wire the Reader
Connect the reader wires to the access controller according to the purpose of each controller terminal. Refer
to Table 1 and the examples that follow for details. For wiring and power requirements, refer to “Wiring and Power”.
Caution: Do not cut the braided directional antenna wire. Wrap it around and secure it to the wiring harness for
future use.
WIRE COLOR PURPOSE TYPICAL X1 SERIES
TERMINALS
TYPICAL 734 SERIES
TERMINALS
TYPICAL KEYPAD
WIRES
Red Power (Positive) R1 RED Red
Black Ground (Negative) B1 BLK Black
White Data 1 W1 WHT White
Green Data 0 G1 GRN Green/White
Blue Green LED LC LC None
Orange Beeper* (optional) BC RA None
Purple Red LED (optional) None None None
Yellow Smart Card Present (optional) None None None
Copper, braided - Do not cut Directional Antenna (optional) None - Do Not Cut None - Do Not Cut None - Do Not Cut
* If connected, the orange wire (beeper) mimics keypad beeping.
Table 1: Wire Connections
SR3 Installation and Programming Guide | Digital Monitoring Products 1
GET STARTED
SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
reader protocol to communicate with door controllers or access control modules.
Procedure
The installation must follow this procedure:
Step 1 (Technician): Install the reader.
Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.
Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.
Step 4 (Customer): Assign credentials to a user in Virtual Keypad.
Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad.
Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.
This guide walks you through all 6 steps.
What’s Included
What You’ll Need
▶Drill
▶If mounting with wall anchors, a 5/16” (8.0 mm) drill bit
▶If mounting without wall anchors, a 5/64” (2.0 mm) drill bit
▶#1 Phillips screwdriver
▶#2 Phillips screwdriver
▶Pliers
▶Wire connectors
▶Electrical tape
SR3 Installation and Programming Guide | Digital Monitoring Products 1
GET STARTED
SR3 Bluetooth and Proximity Readers support Mobile Credentials and 125 kHz proximity credentials. The reader comes
with two mounting options, mullion or single-gang, and is suitable for indoor or outdoor use. The SR3 uses the Wiegand
reader protocol to communicate with door controllers or access control modules.
Procedure
The installation must follow this procedure:
Step 1 (Technician): Install the reader.
Step 2 (Technician): Enroll and associate the reader with a system in Tech APP.
Step 3 (Administrator): Purchase credentials for a customer in Dealer Admin.
Step 4 (Customer): Assign credentials to a user in Virtual Keypad.
Step 5 (End User): Bind a mobile credential to a user’s device in Virtual Keypad.
Step 6 (End User): Use the credential at the SR3 Bluetooth Reader.
This guide walks you through all 6 steps.
What’s Included
What You’ll Need
▶Drill
▶If mounting with wall anchors, a 5/16” (8.0 mm) drill bit
▶If mounting without wall anchors, a 5/64” (2.0 mm) drill bit
▶#1 Phillips screwdriver
▶#2 Phillips screwdriver
▶Pliers
▶Wire connectors
▶Electrical tape
Full Installation Guide
To view the full SR3 Installation Guide (LT-2505), scan this QR code or visit DMP.com.
This quick start guide walks you through Step 1 and Step 2. For the full installation guide, follow the QR code below.

18205
LT-2519 21343
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
Domestic: 800.641.4282 | International: 417.831.9362
DMP.com
© 2021
LED Operation
LED COLOR LED BEHAVIOR MEANING
None None No power or LED not connected
Yellow Spinning Powering on
Yellow Steady Connected to power, ready for enrollment
White Steady Enrolled, waiting for credential
Blue Spinning Searching for credential
Green Flash Access Granted
SR3 Installation and Programming Guide | Digital Monitoring Products 15
Specifications
Operating Voltage 12VDC
Current Draw 100 mA typical at 12 VDC
135 to 155 mA max at 12VDC
Read Range Adjustable, range 3.0 in to 30 ft (7.62 cm to 9.14 m)
Operating Temperature -27 °F to 151 °F (-33 °C to 66 °C)
Recommended Humidity 85% RH or lower, non-condensing
IP Rating IP65
Dimensions 6.0” x 1.7” x 1.3” (15.24 cm x 4.32 cm x 3.30 cm)
Weight 0.5 lb (0.23 kg)
Compliance Requirements
Wiring and Power
▶Connections must be made in accordance with NFPA 70: Do not connect to a receptacle controlled by a switch
▶Shield must run continuously from the reader to the panel
▶The reader ground, shield line, and earth ground must be connected to a single point at the panel
▶To avoid creating a ground loop, do not ground the shield line at the reader
▶Minimum wire gauge is 24 AWG with a maximum single wire run length of 500 ft (150 m)
UL 294
For UL 294 Compliance, the readers shall be connected to a class two power limited power supply or control panel
output.
Certifications
▶FCC Part 15 RFID Reader FCC ID: 2ANJI-SR3
▶Industry Canada ID: 10727A-SR3
Underwriters Laboratory (UL) Listed
ANSI/UL 294 Access Control System Units
Level I Destructive Attack, Line Security, Standby Power
Level III Endurance
Mobile Device and Software Requirements
▶The SR3 uses BLE Version 4.2 or higher
▶Android devices with Version 8.0 (Oreo) or higher and Bluetooth enabled
▶iOS devices with Version 10.0 or higher and Bluetooth enabled
▶Tech APP (Version 2.15.0 or higher) and Virtual Keypad (Version 6.35.0or higher)
▶Compatible with Mobile Credentials and 125 kHz proximity credentials
SR3 Installation and Programming Guide | Digital Monitoring Products 6
STEP 2: ENROLL & ASSOCIATE THE READER
A technician on site must associate each reader with a system before mobile credentials can be purchased in Dealer
Admin by an Administrator.
Note: For XR Series panels with 734 Series Access Control Modules, ensure Program 734 Options is turned on and
Card Options is set to Custom in Device Setup before proceeding.
1. Stand at the reader and ensure your device has Bluetooth turned on.
2. Open Tech APP, then find and open the appropriate system.
3. Tap the Bluetooth Readers tile.
4. Tap Add. Name the reader, then tap Create.
5. When prompted, touch your device to the reader. When paired successfully, the reader beeps.
6. In Tech APP, open the reader you added. Use the slider to adjust the Reader Range closer or farther as needed.
Range is 3in to 30ft (7.62 cm to 9.14 m).
7. To update the reader’s firmware, go to Firmware and tap Update. If no new firmware is available, this button is not
displayed.
8. Tap Save.
After being enrolled and associated, the reader’s LED changes from steady yellow to steady white.
If you receive a message that states the 56-bit card format cannot be added, you must add the format manually in Full
Programming > Device Setup > Card Formats. For more information, refer to “56-Bit Card Format”.
56-Bit Card Format
NAME WIEGAND CODE
LENGTH
SITE CODE
POSITION
SITE CODE
LENGTH
USER CODE
POSITION
USER CODE
LENGTH
USER CODE
DIGITS
BLUETOOTHFORMAT 56 1 16 17 34 10
Configuring the Reader in Tech APP
Enroll & Associate the Reader in Tech APP