DMP Electronics CURVE-F-STAND User manual

English
Installation Instruction
1
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure
that all components were received undamaged. Do not use damaged or defective
parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
! Install and operate this device with care. Please read this instruction before
installation, and carefully follow all instructions contained herein. Use proper safety
equipment during installation.
! Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaims any and all liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Par ts List
2
(1) 48mm Pole-a (1) Weighted Base-b (4) Side Vesa Plate
with Slip Set-c1
(1) Middle Vesa
Plate-c2
(4)Arm Plastic
Cover-i
(2) Arm Clamp-f (8)M6x25 Bolt-g (8)M6 Washer-h
(20)M4 Space-s
(20)M4x30 Bolt-r (4)M8x10 Bolt-t
(40)M4 Washer-p
(1)Allen Key-o
(1)M10 Washer-n1 (1)Spring Washer-n2
(1) -lGrommet Plate(1) kDecorative Cover-(3)M6x29 Bolt-j (1)M10 Grommet
Bolt-m
(2) Long Arm-d1 (1) Arm Connect
Part-e1
(2) Short Arm-d2 (1) Arm Connect
Part-e2
(4)Wire Clip-u (2)M4x16 Bolt with washer-v (1)Wrench-w
(20)M4x12
Thumb Bolt-q

Step 1 Mounting the base according to your requirement
3
Option 2 Option 3
Option 1
a
b
k
j
The stand can be used with the weighted
metal base or there is a desk attachment
provided (as drawings on the bottom)
allowing you to mount the stand on a desk.
This is very simple to install and just
requires a hole drilling (10mm diameter) in
your desk and clamping with the bolt and
large washer.
a
k
a
k
b
j
l
m
n2
n1
l
m
n2
n1

4
Step 3 Mount the Monitor to VESA Plate
Step 2 Assemble the Arm Sets and Install it on the Pole
For Curved Back Monitor
s
p
r
p
t
Assemble the curved arm sets as the
diagram above, fasten the M6x25
Bolt-g by provided Allen Key-o.
Insert the curved arm sets to pole,
fasten the M8x10 Bolt-t by provided
Allen Key-o. Install the Wire Clip-u.
u
d1
ghe1
f
d2
ghe2
f
For Flat Back Monitor
p
q

Step 4
Step 5
Attach the Monitors to Arm Sets
Adjust the Tilting Angle and the Monitors Level
5
Fasten the grub screw to fix the tilting
angle by provided Allen Key-o.
grub screw
Attaching the monitors to the curved arm sets, fasten the M4x16 Bolt with
Washer-v, fixing the position by the plastic knob. Install the Arm Plastic Cover-i
as the above diagram.
i
Bolt
By fasten or loosen the bolt on the
above diagram to adjust the level of
each monitor.
Plastic Knob
c1
vc2
c1
c1
c1

Step 6 Manage the Wires
6
Thank you for choosing our products!