Docking Drawer Trio User manual

Docking Drawer Trio™
Installation Instructions
Tools Needed:
• Jigsaw
• Drill
• Measuring Tape
• Screwdriver
• Square
• Pencil
• Cutout Template
Time Required - 30 min
DOCKING DRAWER
TRIO PART #:
3030-xxx0
DOCKING DRAWER
TRIO PART #:
3040-xxx0
for Docking
Drawer Trio
DOCKING DRAWER TRIO
Step 2 - Remove the included cutout
template.
Step 4 - With a 13mm drill bit, drill a hole in
each corner, being careful not to splinter the
wood on the inside of the drawer box. Using
one of the 13mm holes, insert a jigsaw and then
make the required cutouts in the drawer box.
Step 3 - Locate the proper location for
the receptacle box cutout using our cutout
template. You can locate the proper location
from either the inside or backside of the
drawer box, making sure that the arms will
not interfere with the slides and that there is
enough material surrounding the receptacle
box to securely hold it in place.
• Failure to follow these instructions can cause
death or permanent injury. Do not work on
live electrical circuits! Make absolutely certain
power is o before connecting the device!
• This product is for dry, indoor and permanent
installations only.
• Install the device in accordance with all
national and local electrical codes.
CAUTION – READ CAREFULLY
for Docking
Drawer Trio
CUTOUT TEMPLATE
Step 5 - Reinstall the drawer box and slide
the Docking Drawer Trio receptacle box
through the cutout. Secure it with the 4 wood
screws provided.
Step 3 - cont.
DOCKING DRAWER
TRIO PART #:
3050-xxx0
Downloadable Resources
For additional planning resources, visit
dockingdrawer.com/downloads
• Spec Book
• Mounting Diagrams
• DXF and STEP Files
• Electrical Certications
How to Install the Outlet
There are 3 methods to install the Trio Series
depending on your drawer box type. The
following instructions detail the installation
process for Shallow drawer box types. Need
more detail for the other options? Call us at
[phone].
Step 1 - Verify there is space available for the
in-drawer outlet behind the drawer box. The
Docking Drawer Trio requires at least 51mm
of space behind the drawer box and 381mm
minimum drawer box width.
DOCKING DRAWER TRIO PART #: 3030-xxx0 3040-xxx0 3050-xxx0
CUTOUT TEMPLATE for Docking Drawer Trio
FOR ACCURACY SCALE PRINTER TO 100%

Step 6 - Align arms. With the drawer mostly
closed, mark the position of the rear mounting
bracket. It is important to make sure the
drawer moves freely in and out and that the
arms are square and even. Spend sucient
time at this step before fastening the bracket
to the rear wall to make sure everything
is square and the arms are in the correct
position. Once that is done, secure with the 3
rear mounting bracket screws provided.
Step 7 - Install the cover plate.
Step 8 - Connect the Docking Drawer power
cord to the in-cabinet electrical supply. For
more details about locating an in-cabinet
electrical supply for your Docking Drawer
installation, please refer to the Electrical
Planning Guide located in our Spec Book.
DD082222
For private households: Information
on Disposal for Users of WEEE This
symbol (gure 1) on the product(s) and
/ or accompanying documents means
that used electrical and electronic
equipment (WEEE) should not be
mixed with general household waste.
For proper treatment, recovery and
recycling, please take this product(s) to designated
collection points where it will be accepted free of charge.
Alternatively, in some countries, you may be able to
return your products to your local retailer upon purchase
of an equivalent new product.
Disposing of this product correctly will help save valuable
resources and prevent any potential negative eects
on human health and the environment, which could
otherwise arise from inappropriate waste handling.
Please contact your local authority for further details
of your nearest designated collection point. Penalties
may be applicable for incorrect disposal of this waste, in
accordance with you national legislation.
For professional users in the European Union
If you wish to discard electrical and electronic equipment
(EEE), please contact your dealer or supplier for further
information.
For disposal in countries outside of the
European Union
This symbol is only valid in the European Union (EU). If
you wish to discard this product please contact your local
authorities or dealer and ask for the correct method of
disposal.
[email protected]
www.dockingdrawer.com
[phone]



How to Operate the Outlet
The Docking Drawer Trio Series in-drawer
outlets include a 50˚C interlocking thermostat
to protect against overheating inside the
drawer. To reset, correct the source of over
temperature and push the button in the center
of the vents of the cover plate. Note: You may
need to wait a few minutes for the unit to cool
before the thermostat can be reset.
Push to reset
interlocking
thermostat