Docucap DocketPORT 468 User manual

Compact, Fast and Easy to Use
User Guide

- 1 -
CE Conformity and FCC Statement …………………
This equipment has been tested and found to comply with the limits of the European Council Directive on the
approximation of the member states relating to electromagnetic compatibility according to
EN 55022/55024 Part 15 B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Increase the separation between the equipment and receiver
Move the computer away from the receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Trademarks
Windows, Windows 2000, XP, Vista, 7 and Microsoft are the registered trademarks of Microsoft Corporation.
What’s included with this package …………………

- 2 -
Contents …………………
CE Conformity and FCC Statement ……………………1
Introduction to DocketPORT®468 Scanner ………………2
Installation of Software & Hardware ………………………3
Initial Calibration with DocketSCAN II®…………………..6
Using Your Scanner …………………………………………7
Initial Setup with Presto! PageManager 7 …………………9
Tips & Cautions ……………………………………………10
Technical Support & Product Warranty Information ……....11
Welcome …………………
Thank you for purchasing our DocketPORT®468 document scanner.
We have designed this product to provide the user with a simple but effective tool to
capture, manage and archive documents of many types. We encourage you to read this
short but important User Guide carefully.
Your DocketPORT®468 scanner has the latest technology and compatible drivers. These
drivers are tested and certified by our in-house testing lab to be compliant with Windows 7,
Windows Vista, Windows XP (SP3), Windows 2000 (SP4) operating systems. We also
feature a TWAIN 1.9 compatible driver that will work with thousands of imaging
applications. If you experience any difficulty with these drivers, please check our website
www.docucap.com to verify that you are using the latest version.

- 3 -
Installation of Software & Hardware …………………
(FOR BEST RESULTS PLEASE INSTALL THE SOFTWARE FROM THE CD PROVIDED
BEFORE PLUGGING IN YOUR SCANNER)
NOTE:As a precaution, a RED warning label has been placed over the computer end of the USB plug to remind you to install
the software CD first. Remember to remove this warning label prior to using the USB cable.
Install Scanner Driver Software
a) Insert the installation CD into your CD-ROM drive.
b) The installation program will begin automatically.
c) Select “Install Scanner Driver” option and follow the installation instruction.
d) If your CD does not start automatically then double-click the MY COMPUTER icon on your
Windows desktop, then double-click the CD-ROM drive icon.
You can also manually start the installation by selecting the SETUP.exe icon located in the Driver
folder on the CD.
e) Accept the EULAagreement and select the Complete installation button.
f) Follow the on screen step-by-step setup instruction to complete the installation.

- 4 -
g) At the end of the driver installation process you will be redirected back to the main menu.
h) If you wish you can update toAdobe Reader 9.3 at this time or at a later time.
i) If you don’t have any scanning application, then install DocketSCAN II now.
j) You can always update or install these applications at a later time.
NOTE: After you have completed all your software installations, we strongly recommend that you
restart your computer even though you are not requested by Windows to do so.
Uninstall Scanner Driver Software
a) If you should need to un-install the scanner driver, you can do so by inserting the installation CD
and run the “install driver” setup again. (Or you can uninstall DocketPORT 468 in Uninstall or
change a program in Programs and Features under Control Panel.)
b) The second installation process will display a different setup window.
c) Select the Remove option and your scanner driver will be uninstalled.
d) To remove PageManager 7 orAdobe Reader 9.3 you will need to uninstall these from Programs
and Features: Uninstall a program under Control Panel.

- 5 -
Install Scanner hardware
NOTE: Proceed with this step only if you have successfully install the scanner driver.
a) Connect the USB cable provided to your computer and scanner. The installation will proceed
automatically.
b) Make sure the red warning label is removed before connecting this end to your computer.
c) You may need to reconnect the cable to another USB port on your computer if the scanner
cannot be detected initially. (Check your computer’s user guide to identify other available USB
ports and their locations.
d) When your software has been installed successfully you will see the following information
displayed from your system tray when you connect the scanner to your computer:

- 6 -
Initial Calibration with DocketSCAN II®…………………
NOTE: Calibration is a critical step in setting up your scanner. It allows the image quality to
be “balanced” for your computer and scanner combination. If at any time you switch the
computer that you use with your scanner, or change scanners, you will be required to calibrate
again.
To launch the DocketSCAN®II application you can either double-click the DocketSCAN II
icon in your system tray or shortcut icon on your desktop or the “Taskbar tray” icon
(usually in the lower right-hand corner of the Windows desktop).
Once you have launched DocketSCAN II®for the first time, you should select the SCAN
button and the step-by-step calibration instructions will appear in a succession of prompts.
This calibration process will require the special black and white calibration sheet that was
included with your scanner. When calibrating make sure the page with the black bars are
facing down and note the direction of the arrows for proper insertion. When the
calibration process has been completed successfully, you will see the message above
otherwise you would need to re-calibrate again.
If you switch scanners or your image quality has become unsatisfactory, you can
re-calibrate your scanner by choosing the CUSTOM button in the DocketSCAN II® window
and select the Calibrate button.
Should you lose or forget the black and white calibration paper that was included with your
scanner, you can simply use any plain “white” (the brighter the “white” the better) piece of
letter size (orA4) printer paper to perform the calibration. Simply fold the paper in half
and insert the folded end into the scanner first when calibrating.
The following message will be displayed (see below).

- 7 -
Using your Scanner …………………
There are two easy ways for you to scan and manage your documents and images with your
DocketSCAN II®. When scanning documents make sure the front image side to be
captured is inserted faced down.
The first is by utilizing the document manager control panel (shown below) that allows you
to select from the most common paper sizes, image settings and basic file output
information (location & name of your document). You can save your scans as PDF, JPG,
or TIFF format files.
The second way is through the TWAIN control panel, which you can find by pressing the
“Custom…” button on the DocketSCAN II®control panel. The TWAIN control panel
(shown below) allows you to control all details and settings of the scanner. This type of
“fine-adjustment” of your scans may be required for some of your document needs.

- 8 -
Please notice the page tabs at the top of the TWAIN control panel; they are: Pre-defined
Setting, Custom Settings, Information, and Language. Take a moment to explore these
Tabs and their function. The Information tab provides important information regarding the
software driver version. This may be required if you want to know if the software you are
using is the latest version. The Language tab allows you to switch the text of the TWAIN
control panel to another language.
The Pre-defined Setting Tab allows you to quickly choose the most frequent and common
scan setting. These are designed for your convenience. The settings are viewed once you
click “Acquire” and can be easily launched by selecting their respective user interface.
The Custom Settings control panel allows you to change the settings to the detailed specification that
you feel are required. You can adjust the Mode, Resolution, Filter (None or De-screen) together with
scanning size. In addition, you can also adjust the Brightness, Contrast, Color (Gamma), Highlight
and Shadow of the image with the 5 slide-bar controls. In case you forget the original settings of
these slide-bar controls, you can press the RESET button, which restores these settings to the scanner
default settings. Once your settings are defined, select either “Preview” button to take a quick look
at how your image will look in the scanning window or you can press “SCAN” button to perform final
scanning.
Using DocketPORT®468 scanner with other applications
DocketPORT®468 scanner is fully TWAIN compliant, you can use it with literally thousands of
applications that use standard TWAIN device input. From desktop publishing to games, and from
faxing to business card scanning, you will discover many useful applications for this scanner. Simply
select the scanner source from your program’s “source” options and look for DocketPORT®468.
Sometimes these “source” scanner options may be found under TWAIN devices available or “import
from”.

- 9 -
Initial Setup with Presto! PageManager 7 …………………
NOTE: Calibration is a critical step in setting up your scanner. This process will balance the image quality between
your computer and the scanner unit. If at any time you switch the scanner to another computer then you will need
to reinstall the scanner driver and recalibrate the scanner.
Selecting Scanning Source
a) When using Presto! PageManager 7 for the first time you will need to define the Scanning Source
this application will be using. This also applies when switching to another scanner.
b) Run the PageManger7 application and select file in the toolbar menu.
c) Under file pull-down menu choose the Select Source option, then your model.
Performing Scanner Calibration under TWAIN
a) Tools Scan Settings uncheck Suppress TWAIN User Interface
b) To calibrate your scanner select the Acquire Image Data icon (scanner and camera icon) under the
toolbar menu.
a) The TWAIN user interface screen will appear.
b) Insert the calibration target with the printed arrow end first.
c) Make sure the black bar side is inserted facing down then select the Calibration button.
NOTE: When the image quality has become unsatisfactory, we recommend you clean the scanner with the included cleaning
sheet(see Tips & Cautions page) and then recalibrate the scanner.
If you lose or forget the calibration target when traveling, use any plain “white” piece of printer paper to perform the
calibration. The following message will appear (see below). Select “OK” and proceed to scanning.