Dodge 75 User manual

1
WARNING: Only qualified electrical personnel familiar with
the construction and operation of this equipment and the
hazards involved should install, adjust, and/or service this
equipment. Failure to observe this precaution can result in
bodily injury.
WARNING: The user is responsible for conforming to the
National Electrical Code and all other applicable local codes
in respect to wiring practices, grounding, disconnects,
and overcurrent protection. Installation of an approved
disconnecting means in the line side of the controller is of
particular importance. Failure to observe these precautions
could result in severe bodily injury or loss of life.
WARNING: Subsequent steps require rotating parts and/or
electrical circuits to be exposed. Stay clear if unit must be
running or disconnect and lockout or tag power source if
contact must be made. Failure to observe these precautions
could result in severe bodily injury or loss of life.
WARNING Because of the possible danger to persons(s) or
property from accidents which may result from the improper
use of products, it is important that correct procedures be
followed. Products must be used in accordance with the
engineering information specified in the catalog. Proper
installation, maintenance and operation procedures must
be observed. The instructions in the instruction manuals
must be followed. Inspections should be made as necessary
to assure safe operation under prevailing conditions. Proper
guards and other suitable safety devices or procedures as
may be desirable or as may be specified in safety codes
should be provided, and are neither provided by Baldor
Electric Company nor are the responsibility of Baldor
Electric Company. This unit and its associated equipment
must be installed, adjusted and maintained by qualified
personnel who are familiar with the construction and
operation of all equipment in the system and the potential
hazards involved. When risk to persons or property may
be involved, a failsafe device must be an inegral part of the
driven equipment beyond the speed reducer output shaft.
Installation Manual for DODGE Model 75 Power Supply
These instructions must be read thoroughly before installing or operating this product.
Specifications
Input voltage: 230 VAC 50-60 Hz, 1 phase
Output voltage: 100 VDC Nominal
Output current: 0.4 Amp Maximum
Output wattage: 80 Watts Maximum
Dimensions: 0.62” H, 1.40” W, 0.90” D
Description:
Model 75 is a power supply that can be mounted in a
Clutch and/or Brake conduit box. The power supply
converts 230 VAC to 100 VDC.
Model 67 power supply kit includes:
Model 75 power supply (quantity 1)
Two-sided tape (quantity 1)
Wire nuts (quantity 4)
Connection Instructions (See Figure 1):
1. Disconnect and lockout power to the Clutch and/or Brake
unit.
2. Remove conduit box cover and separate the incoming
power leads to the coil(s).
3. Connect power supply as shown in Figure 1, using supplied
wire nuts to secure connections.
Note A: Polarity of wiring is immaterial.
Note B: Customer must supply any switching or fuse for
230 VAC input line voltage.
Note C: The power supply is suitable for clutches and
brakes rated 90 VDC.
4. Use two-sided tape to secure power supply to the inside
wall of the conduit box.
5. Reattach the conduit box cover making sure not to pinch
wiring.
230
Vac
blue
blue
red
black
coil
*
*
* Clutch coil lead wires are black.
Brake coil lead wires are white.
Figure 1 - Wiring Diagram

World Headquarters
P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.646.4711, Fax [phone], International Fax [phone]
Dodge Product Support
6040 Ponders Court, Greenville, SC 29615-4617 U.S.A., Ph: (1) 864.297.4800, Fax: [phone]
www.baldor.com
All Rights Reserved. Printed in USA.
11/10 Printshop 500
© Baldor Electric Company
MN4007 (Replaces 499060) *4007-1110*