DOL 104 0-3 V Manual

Technical User Guide
DOL 104 0-3 V
Humidity Sensor
dol-sensors a/s – Agro Food Park 15 – DK-8200 Aarhus N – T: [phone] – F: [phone] – www.dol-sensors.com

Technical User Guide
2www.dol-sensors.com DOL 104 0-3 V
1 Product description
DOL 104 is a high-precision sensor for measuring relative humidity. It is intended for use in livestock houses
but is also well suited for a number of industrial applications.
The sensor features one analogue output with full protection against short-circuits and wiring failures.
The special sensor element and the built-in Teflon filter enable application in livestock houses with constantly
high humidity.
The sensor is microprocessor-controlled and has a two-color light emitting diode (LED) to communicate the op-
eration status and the error diagnostic.
2 Mounting guide
For optimum mounting of the sensor, use mounting clip or mount it free-hanging
in the cable.
The sensor element of the sensor requires free air passage.
Mount the sensor so it is not exposed to direct sunlight, as this would affect the
measurement.
Remember to put on a protection cap before mounting the cable.
3 Installation guide
Installation, servicing and troubleshooting of all electrical equipment must be carried out by quali-
fied personnel in compliance with the applicable national and international standard EN 60204-1
and any other EU standards that are applicable in Europe.
3.1 Connection of the sensor
Supply voltage
11-30 V DC
+ V (Brown)
+ GND (Blue)
% RH (White)
Signals and wire colors

Technical User Guide
DOL 104 0-3 V www.dol-sensors.com 3
LED/LIGHT PROTOCOL Functional graph
LED Status
Green Red
ON Operation OK
Flash Outside normal range
(below 10 % RH or exceeding 95 %
RH)
ON Connection error
Load < 500 Ω
Flash Sensor defect
Over or under voltage alarm
Overload
4 Maintenance
When cleaning and disinfecting the house, the protective cap must be put on the sensor so that it hangs with
the tip up, as shown in the picture.
Sensor is cleaned with: • Water and brush
• High-pressure cleaning with cold water (only with attached protective cap)
Avoid using:
• High-pressure cleaning with hot water
• Highly compressed air
• Solvents
• Corrosive/caustic agents
• Alcohol-based disinfectants
After the sensor has been exposed to water and condensation, it requires a period where the relative humidity
is lower than 80 %RH in order for it to measure correctly.
Do not bend the sensor as this would inflict permanent damage on the electronics of the sensor.
5 Technical data
Measuring range % RH 0 - 100
Accuracy % RH ± 3% RH (40–85 %) ± 4% RH (10-95 %) at 0-40 °C
Output signal V 0.03 V / % RH
Time constant T63 20 s at 0.5 m/s air speed
Supply voltage V DC 11 – 30
Current mA 12 mA no load
35 mA max. load
Load Ω > 500 Ω - < 10 MΩ

Technical User Guide
dol-sensors a/s – Agro Food Park 15 – DK-8200 Aarhus N – T: [phone] – F: [phone] – www.dol-sensors.com
Recommended load kΩ ≥ 100
Max. output current mA 20
Output impedance Ω < 1
Cable 2 m 3 x 22 AWG / 0.34 mm2
Max. Cable length at 0.75
mm2
m 100
Max. Cable length at 1.50
mm2
m 200
Temperature, operation and
storage
°C -40 to +60
Protection class IP 67
Measurement, shipment mm 275 × 200 × 20
Shipment weight ex. connec-
tor
g 150
5.1 Dimensions
Dimensions in mm.
154
107.54
604258 • 2023-09-06 • en-US • Made in Denmark