Dometic MS680 User manual

1
COMFORT
COMFORT
1.
2.
3.
4.
5.
2.
1.
3.
Click!
Click!
Ø 15 mm
1
3
75
2
1
6
89
4
23
4
1
2
3
3
1
1
2
MS680
EN: 7
DE: 30
FR: 56
ES: 81
PT: 105
IT: 129
NL: 153
DA: 177
SV: 199
NO: 221
FI: 244
RU: 266
PL: 291
SK: 315
CS: 338
HU: 361
EN: 9
DE: 32
FR: 58
ES: 83
PT: 107
IT: 131
NL: 155
DA: 179
SV: 201
NO: 223
FI: 246
RU: 269
PL: 294
SK: 317
CS: 340
HU: 363
EN: 11
DE: 34
FR: 60
ES: 85
PT: 109
IT: 133
NL: 157
DA: 181
SV: 203
NO: 225
FI: 248
RU: 271
PL: 295
SK: 319
CS: 342
HU: 365
1
4
7
5
8
23
6
faltblatt_abbildungen.fm Seite 1 Mittwoch, 7. September 2016 11:19 11

2
Dometic WAECO International GmbH
Hollefeldstrasse 63
D-48282 Emsdetten
www.dometic.com
10 20
1 11
60
45
46
30
31
15
16
1
12
56
34
78
12345
11
10
1213
6
7
89
14151617181920
ge
ge
bl/sw
ge/bl
gr/sw
Fiat Ducato x290
gr/sw
br/sw
bl/sw
bl/sw
vt
sw
sw
rt
rt
grgr
gr
bl bl/br
38
7
59
6
4
1 10
13
11
12
2
9
EN DE FR ES PT IT NL DA
bl Blue Blau Bleu Azul Azul Blu Blauw Blå
br Brown Braun Marron Marrón Castanho Marrone Bruin Brun
ge Yellow Gelb Jaune Amarillo Amarelo Giallo Geel Gul
gr Grey Grau Gris Gris Cinzento Grigio Grijs Grå
rt Red Rot Rouge Rojo Vermelho Rosso Rood Rød
sw Black Schwarz Noir Negro Preto Nero Zwart Sort
vt Violet Violett Violeta Lila Violeta Violetto Paars Violet
SV NO FI RU PL SK CS HU
bl Blå Blå Sininen Синий Niebieski Modrá Modrá Kék
br Brun Brun Ruskea Коричневый Brązowy Hnedá Hněda Barna
ge Gul Gul Keltainen Желтый Żółty Žltá Žlutá Sárga
gr Grå Grå Harmaa Зеленый Zielony Zelená Zelená Szürke
rt Röd Rød Punainen Красный Czerwony Červená Červená Piros
sw Svart Svart Musta Черный Czarny Čierna Černá Fekete
vt Violett Fiolett Violetti Фиолетовый Fioletowy Fialová Fialová Ibolya
4445101744 08/2016
faltblatt_abbildungen.fm Seite 2 Mittwoch, 7. September 2016 11:19 11

MS680
Alarm system
Installation and Operating Manual. . . . . . . . 3
Alarmanlage
Montage- und Bedienungsanleitung . . . . .26
Système d'alarme
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . . 51
Sistema de alarma
Instrucciones de montaje y de uso . . . . . . .77
Sistema de alarme
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Sistema di allarme
Istruzioni di montaggio e d’uso . . . . . . . .125
Alarminstallatie
Montagehandleiding en
gebruiksaanwijzing . . . . . . . . . . . . . . . . . .149
Alarmanlæg
Monterings- og betjeningsvejledning . . . 173
Larmsystem
Monterings- och bruksanvisning . . . . . . . 195
Sinus vekselretter
Monterings- og bruksanvisning . . . . . . . . 217
Varashälytin
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 240
Автомобильная система
сигнализации
Инструкция по монтажу и
эксплуатации . . . . . . . . . . . . . . . . . . . . . . 262
System alarmowy
Instrukcja montażu i obsługi. . . . . . . . . . . 287
Poplašné zariadenie
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 311
Poplašné zařízení
Návod k montáži a obsluze . . . . . . . . . . . 334
Riasztóberendezés
Szerelési és használati útmutató . . . . . . . 357
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
SAFETY SOLUTIONS
ALARM SYSTEMS
MS-680-IO-16S.book Seite 1 Mittwoch, 7. September 2016 11:20 11

MS-680-IO-16S.book Seite 2 Mittwoch, 7. September 2016 11:20 11

EN
MS680
3
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
7 Installing the alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
8 Connecting the alarm system electrically . . . . . . . . . . . . . . . . . . . . . . . . . . .12
9 Programming the alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
10 Using the alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
11 Care and cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
13 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
14 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MS-680-IO-16S.book Seite 3 Mittwoch, 7. September 2016 11:20 11

EN
Explanation of symbols MS680
4
1 Explanation of symbols
!
!
A
I
2 Safety and installation instructions
The manufacturer accepts no liability for damage in the following cases:
•Faulty assembly or connection
•Damage to the product resulting from mechanical influences and excess voltage
•Alterations to the product without express permission from the manufacturer
•Use for purposes other than those described in the operating manual
Pleaseobservetheprescribedsafetyinstructionsandstipulationsfromthe
vehicle manufacturer and service workshops.
!WARNING!
Inadequate supply cable connections could result in short circuits, which
could have as a consequence that:
•Cable fires occur
•The airbag is triggered
•Electronic control devices are damaged
•Electric functions fail (indicators, brake light, horn, ignition, lights)
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
MS-680-IO-16S.book Seite 4 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Safety and installation instructions
5
ANOTICE!
To prevent the risk of short circuits, always disconnect the negative termi-
nal of the vehicle's electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be
disconnected.
Please observe the following instructions:
•When working on the following cables, only use insulated cable lugs, plugs and
flat push-on receptacles:
– 30 (direct supply from positive battery terminal)
– 15 (connected positive terminal, behind the battery)
– 31 (return line from the battery, earth)
– L (indicator lights left)
– R (indicator lights right)
Do not use terminal strips.
•Use a crimping tool to connect the cables.
•When connecting to cable 31 (earth), screw the cable
– to the vehicle's earth bolt with a cable lug and a gear disc or
– to the sheet-metal bodywork with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
If you disconnect the negative terminal of the battery, all data stored in the volatile
memories will be lost.
•The following data must be set again, depending on the vehicle equipment
options:
–Radiocode
– Vehicle clock
–Timer
– On-board computer
– Seat position
You can find instructions for making these settings in the appropriate operating
instructions.
Observe the following installation instructions:
!CAUTION!
•Secure the parts installed in the vehicle in such a way that they cannot
become loose under any circumstances (sudden braking, accidents)
and cause injuries to the occupants of the vehicle.
MS-680-IO-16S.book Seite 5 Mittwoch, 7. September 2016 11:20 11

EN
Safety and installation instructions MS680
6
•Secure any parts of the system covered by the bodywork in such a
manner that they cannot be come loose or damage other parts and
cables or impair vehicle functions (steering, pedals, etc).
•Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may
only be performed by qualified specialists.
ANOTICE!
•To prevent damage when drilling, make sure there is sufficient space
on the other side for the drill head to come out.
•Deburr all drill holes and treat them with a rust-protection agent.
Observe the following instructions when working with electrical parts:
ANOTICE!
•When testing the voltage in electrical cables, only use a diode test
lamp or a voltmeter.
Test lamps with an illuminant take up voltages which are too high and
which can damage the vehicle's electronic system.
•When making electrical connections, ensure that:
– they are not kinked or twisted
– they do not rub on edges
– they are not laid in sharp edged ducts without protection.
•Insulate all connections.
•Secure the cables against mechanical wear with cable binders or insu-
lating tape, for example to existing cables.
MS-680-IO-16S.book Seite 6 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Scope of delivery
7
3Scopeofdelivery
See fig. 1
4Accessories
Available as accessories (not included in the scope of delivery):
No. Quantity Description Ref. no.
1 1 Control unit 9101600015
2 1 Siren MS-670-SI
3 2 Ultrasonic sensors
4 1 Radio remote control 9101600016
5 1 Ultrasonic module (including sensors) MS-670-US
6 1 Electronic key (e-key) with base
7 1 Vehicle-specific cable set with OBD plug
8 1 Bonnet contact switch
9 1 Holder for bonnet contact switch and siren
– – Fastening and installation material
– – Installation and operating manual
Description Ref. no.
Wireless infrared motion sensor 9101600013
Wireless magnetic contact switch 9101600014
Electronic key MS-670-EK
Electronic key base MS-670-ES
MS-680-IO-16S.book Seite 7 Mittwoch, 7. September 2016 11:20 11

EN
Intended use MS680
8
5 Intended use
MS680 (ref. no. 9101600012) is an alarm system and preset for a Fiat Ducato x290
(manufactured in 2015). Optionally, the alarm system can also be used for a Fiat
Ducato x250 (manufactured in 2011). For the connection data for a Fiat
Ducato x250, refer to chapter “Connection data for Fiat Ducato x250 (without
connection to the central locking system)” on page 15.
The alarm system offers additional protection against the theft of your vehicle and its
contents.
6 Technical description
6.1 Function description
MS680 is an alarm system with two ultrasonic sensors and a siren. The alarm system
can optionally be extended by up to 55 wireless infrared motion detectors and wire-
less magnetic contact switches. It is designed for vehicles with a voltage of 12 V and
is enabled or disabled when operating the original vehicle remote controls.
When the alarm system is activated, an alarm is triggered when one of the following
events occurs:
•A door opens.
•The boot is opened.
•The bonnet is opened.
•The ignition is turned on.
•An (optional) wireless sensor (radio magnetic contact, wireless motion) reports
movement.
The product offers you the following features:
•Activation and deactivation with original vehicle remote control
•Programmable acoustic and optical signals
•Interior monitoring of the passenger compartment using ultrasonic sensors
•Additional remote control to deactivate the interior monitoring
•E-key (electronic key) for programming and deactivating the alarm system
•Input for the connection of additional door contacts or a contact switch for the
bonnet or the boot.
MS-680-IO-16S.book Seite 8 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Technical description
9
6.2 Control unit
See fig. 2
6.3 Radio remote control
See fig. 3
6.4 Ultrasonic module
See fig. 5
No. Description
1 Connection plug
2 Connection plug for 20-pin connection cable
3 Button (for programming)
4LED
No. Description
1 Deactivates the entire system (including unlocking of the doors upon connec-
tion of the central locking system, see chapter “Optional connection options”
on page 14)
2 Deactivates the interior monitoring system with an activated system or activates
the system without the interior monitoring (including interlock of doors upon
connection of the central locking system, see chapter “Optional connection
options” on page 14)
3 Activates the complete system (including interior monitoring and interlock of
the doors upon connection of the central locking system, see chapter
“Optional connection options” on page 14)
No. Description
1 Ultrasonic sensors
2 Ultrasonic module
3 Adjusting screw
MS-680-IO-16S.book Seite 9 Mittwoch, 7. September 2016 11:20 11

EN
Installing the alarm system MS680
10
6.5 Possible operating states
The alarm system has the following operating modes:
•Stand-by
The alarm system is constantly on stand-by as soon as it is installed and correctly
connected. However, it does not trigger the alarm when in stand-by.
•Activation time
The alarm system has an activation time of approx. 40 seconds.
As an optical indicator of the activation time, the LED is illuminated on the
electronic key base (fig. 41).
•Activated
If the alarm system is activated, it can trigger an alarm. This happens if someone
breaks into the door, opens the bonnet or enters the vehicle interior. If you wish
to drive off, you must first deactivate the alarm system. The system is then in
stand-by mode.
As an optical indicator for activation, the LED flashes on the electronic key base
(fig. 41).
•Alarm triggered
When an alarm has been triggered, it is indicated by optical and acoustic signals.
7 Installing the alarm system
I
7.1 Installing the controller
➤Select a suitable installation location.
➤Install the control unit
– In the vehicle interior
– In such a way that you can read the LED and operate the button
– Under the dashboard
–Not in areas where strong electrical fields could cause interference,
e.g. ignition cables or central control electronics
–Not directly next to ventilator nozzles.
➤Screw the control unit firmly to the vehicle with the screws supplied or use
double-sided adhesive tape.
NOTE
If you do not have sufficient technical knowledge for installing and
connecting the components in vehicles, you should have a specialist
install the alarm system in your vehicle.
MS-680-IO-16S.book Seite 10 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Installing the alarm system
11
7.2 Mounting the siren
See fig. 6
The siren can be mounted in the engine compartment.
A
➤Install the siren and the holder as shown in fig. 6.
7.3 Installing the ultrasonic module
See fig. 5
➤Install the ultrasonic module as illustrated in fig. 5.
7.4 Installing the ultrasonic sensors
See fig. 7
!
➤Align the ultrasonic sensors so that they point towards the centre between the
backrests of the front seats (of the passenger compartment).
➤Lay the connecting cables of the sensors through the A-pillar to the ultrasonic
module.
NOTICE!
When mounting it, ensure that the installation location is
•Not in an area exposed to splashing water
•Not near the exhaust system
•Not accessible from underneath the vehicle, to ensure that it cannot
be tampered with.
CAUTION!
Risk of injury if the airbag deploys!
Do not fit the ultrasonic sensors where an airbag may open.
MS-680-IO-16S.book Seite 11 Mittwoch, 7. September 2016 11:20 11

EN
Connecting the alarm system electrically MS680
12
7.5 Installing the bonnet contact switch
➤Find a suitable location in the engine compartment and drill a hole with a
diameter of 8 mm.
➤During installation make sure the distance to the closed bonnet is between
22 mm and 27 mm.
Use putty, for example, to check this distance.
You can further reduce the minimum distance by shortening the switch.
➤Test the switch function after installation.
➤Connect the bonnet contact switch with the grey wire (fig. 9) of the connection
cable of the siren in the engine compartment.
7.6 Mounting the base for the electronic key
See fig. 8
I
8 Connecting the alarm system
electrically
Fiat Ducato x290: You can find the circuit diagram in fig. 9.
NOTE
When selecting the installation location, pay attention to the cable
lengths and whether the LED in the base is to be visible.
No. Description
1 20-pin plug of the connection cable on the MS680 control unit
2 Connected positive terminal (ignition, terminal 15)
3 Central locking system
4 Central locking system
5 Right-hand indicator
6 Left-hand indicator
7OBDplug
8 60-pin green plug from the vehicle fuse box
9 20-pin black plug from the vehicle fuse box
MS-680-IO-16S.book Seite 12 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Connecting the alarm system electrically
13
All plugs are coded so that you cannot connect them incorrectly.
8.1 Connecting the connection wires of the connection
cable (fig. 9)
Connecting the siren
➤Insert the plug of the connection cable (fig. 911) into the connection of the
ultrasonic module.
➤Guide this open cable end through the splash-protection wall into the passenger
compartment.
➤Connect the red cable of the siren to the red cable of PIN 3 (8-pin plug of the
connection cable on the MS680 control unit) (fig. 910).
➤Connect the blue cable of the siren to the blue/brown cable of PIN 18 (20-pin
plug of the connection cable on the MS680 control unit) (fig. 91).
➤Connect the grey cable to the grey cable of PIN 15 (20-pin plug of the
connection cable on the MS680 control unit) (fig. 91).
➤Connect the black cable to the black cable of PIN 1 (8-pin plug of the connection
cable on the MS680 control unit) (fig. 910).
Connecting the electronic key base
➤Plug the red two-pin connector of the electronic key base (fig. 16) into the red
socket of the connection cable.
➤Plug the white two-pin connector of the electronic key base (fig. 16) into the
white socket of the connection cable.
Violet (ignition plus)
➤Connect the violet cable of PIN 10 (20-pin plug of the connection cable)
(fig. 91) to PIN 16 (20-pin black plug of the vehicle fuse box) (fig. 99).
10 8-pin plug of the connection cable on the MS680 control unit
11 Siren
12 Bonnet switch
13 Power supply connection
No. Description
MS-680-IO-16S.book Seite 13 Mittwoch, 7. September 2016 11:20 11

EN
Connecting the alarm system electrically MS680
14
Connecting the ultrasonic module (fig. 52)
Insert the white 3-pin plug of the connection cable into the connection of the
ultrasonic module.
Connecting the ultrasonic sensors (fig. 51)
➤Insert the red plug of the ultrasonic sensor cable into the red connection of the
ultrasonic module (fig. 95).
➤Insert the red plug of the ultrasonic sensor cable in the white connection of the
ultrasonic sensor (fig. 95).
Yellow (indicator)
➤Connect the yellow cable of PIN 4 (8-pin plug of the connection cable on the
MS680 control unit) (fig. 910) to PIN 18 of the right indicator cable (60-pin
green plug of the vehicle fuse box) (fig. 98).
➤Connect the yellow cable of PIN 8 (8-pin plug of the connection cable on the
MS680 control unit) (fig. 910) toPIN 19 of the left indicator cable (60-pingreen
plug of the vehicle fuse box) (fig. 98).
8.2 Optional connection options
Brown/black (central locking system)
➤Connect the brown/black cable of PIN 17 (20-pin plug of the connection cable)
(fig. 91) to PIN 27 (60-pin green plug from the vehicle fuse box) (fig. 98), if
you would like to also open and lock the vehicle with the additional hand-held
transmitter as well as activate and deactivate the MS680.
Grey/black (central locking system)
➤Connect the grey/black cable of PIN 16 (20-pin plug of the connection cable)
(fig. 91) to PIN 53 (60-pin green plug from the vehicle fuse box) (fig. 98), if
you would like to also open and lock the vehicle with the additional hand-held
transmitter as well as activate and deactivate the MS680.
MS-680-IO-16S.book Seite 14 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Connecting the alarm system electrically
15
Connection data for Fiat Ducato x250 (without connection to the central
locking system)
Yellow – indicator (standard)
➤Connect the yellow cable of PIN 4 (8-pin plug of the connection cable on the
MS680 control unit) (fig. 910) to PIN 18 (blue/black cable) of the right
indicator cable (60-pin green/blue plug of the vehicle fuse box).
➤Connect the yellow cable of PIN 8 (8-pin plug of the connection cable on the
MS680 control unit) (fig. 910) to PIN 19 (blue/white cable) of the left indicator
cable (60-pin green/blue plug of the vehicle fuse box).
Violet – ignition (+15)
➤Connect the violet cable of PIN 10 (20-pin plug of the MS680 connection cable)
(fig. 91) to PIN 18 (light blue/grey) (20-pin black/blue plug of the vehicle fuse
box).
8.3 Connecting the connection cable
➤Insert the 20-pin plug and the 8-pin plug of the connection cable into the
appropriate connection on the control unit of the alarm system (fig. 91 and
fig. 910).
➤Insert the OBD plug (fig. 97) into the OBD connection underneath the vehicle
fuse box.
Red
➤Insert the cable lug (fig. 913) of the red cable of PIN 3 of the 8-pin plug of the
connection cable into the MS680 control unit (fig. 910) in the open slot of the
vehicle fuse box (fig. 9).
MS-680-IO-16S.book Seite 15 Mittwoch, 7. September 2016 11:20 11

EN
Programming the alarm system MS680
16
9 Programming the alarm system
I
9.1 Programming the vehicle code
The alarm system must be adjusted to the CAN bus of your vehicle type. The alarm
system is factory set to the vehicle code 131 for Fiat Ducato x250 and Fiat
Ducato x290.
If you need to reprogram the vehicle code, proceed as follows:
➤Press the button (fig. 23) on the control unit and hold it down.
➤When the LED on the control device (fig. 24) lights up, release the button.
✓The LED goes out.
✓After a pause of 4 seconds, the LED begins to flash.
➤Count the number of flashes until the number agrees with the first number ofyour
vehicle code:
– One flash: Number 1
–Twoflashes:Number2,…
– Nine flashes: Number 9
– Ten flashes: Number 0
➤Press the button again.
✓After a pause of 4 seconds, the LED begins to flash.
➤Repeat the steps described above for all the digits of the vehicle code.
✓After programming, the LED flashes the vehicle code.
➤Test the alarm system by activating it with your remote control.
✓When you correctly enter the vehicle code, the alarm system will be activated.
If the alarm system is not activated, you have not entered the vehicle code correctly.
Repeat the programming.
NOTE
The alarm system is pre-programmed for the Fiat Ducato x290.
MS-680-IO-16S.book Seite 16 Mittwoch, 7. September 2016 11:20 11

EN
MS680 Programming the alarm system
17
9.2 Programming (optional)
You can program the functions listed in the following table. These functions remain
stored even if the battery is disconnected.
To program a function, proceed as follows:
➤Start the ignition with the alarm system deactivated.
✓The LED in the base of the electronic key illuminates for two seconds.
➤Insert the electronic key into the key holder within these two seconds.
✓To indicate that the programming mode has been activated, the LED flashes
three times and the siren emits three acoustic signals.
✓The first function is activated.
INOTE
Each time you call up the programming mode in this way, all the values
of the individual functions are reset to the factory settings (see following
table).
Function Factory
setting LED Programming
Optical signals
during activation/
deactivation
Off Flashes once This function can only be activated for
vehicles which do not emit any
optical signals (e.g. indicator) during
opening or closing.
Acoustic signals Off Flashes twice The following acoustic signals are
emitted:
Activating: 2 signals
Deactivating: 1 long signal
Deactivating when the alarm has
been triggered: 1 brief signal
Passive alarm Off Flashes three
times
This function automatically activates
the alarm system 60 seconds after the
ignition has been switched off.
When this function is activated, the
convenience output and the ultra-
sonic sensors are deactivated.
MS-680-IO-16S.book Seite 17 Mittwoch, 7. September 2016 11:20 11

EN
Programming the alarm system MS680
18
Modifying selected function
➤Insert the electronic key in the electronic key base in order to modify the value of
the selected function.
✓If the factory setting is “On”, the value is set to “Off” and vice versa.
✓The siren emits an acoustic signal, and the LED on the electronic key base flashes
once.
Activating the next function
➤Switch the ignition off and on again.
✓The next function is activated.
➤Modify the value as described above or switch the ignition off and on again to
activate the next function.
➤Once you have called up all functions in sequence, switch the ignition off and on
again to confirm the entered values.
✓The alarm system indicates the leaving of the programming mode and the storing
of the entered values by having the LED on the electronic key base flash three
times and the siren emit three acoustic signals.
Door contact input Negative Flashes four
times
The factory setting switches the
convenience output to negative so
that an external system can be
connected.
Flashes five
times
Do not change the value!
Flashes six
times
Do not change the value!
Function Factory
setting LED Programming
MS-680-IO-16S.book Seite 18 Mittwoch, 7. September 2016 11:20 11