domi LTCF5206 User manual

[e-mail]
© copyright 2019-2023 Domi Outdoor Living LLC. All Rights Reserved.

8-15
17-19
16
20
23
24
21-22

When using the appliance, keep the appliance area clear and free from combustible materials,
gasoline and other flammable liquid and vapors. Certain items or materials, when stored under
the appliance or nearby, will be subjected to radiant heat and could be seriously damaged.

5PSI
2.17mm
ETL

1X Table Top 1X Control Panel 2X Leg A
1X Leg B 1X Leg C 1X Cylinder Holder
1X Front Panel 2X Side Panel 1X Door
1X Glass Beads 1X Cover Lid Ring 1X Cover Lid
1X Cylinder Block Wire 1X Door Handle 15X M5X10 Bolt
4X M4X10 Flat Bolt 15X M6X22 Bolt 1X M6X28 Bolt
1X M4X8 Bolt
16X Steel Flat washers
1X Allen Wrench
1X Phillips Screwdriver 1X Nut 1X Wrench
Estimated time for assembly: 30 minutes.
7

With assistance, place the table
top ① upside down on a soft,
level surface.
Attach the control panel ② to the
table top ① by first inserting the
tip of the valve into the end of the
injection pipe as illustrated.
Then install (2) M5x10 bolts ⑱ to Then install (2) M5x10 bolts ⑱ to
secure the control panel ② to the
table top ①.
Be certain the valve is properly
connected to the injection pipe
of burner, tighten two bolts as
Positon 1
Insert
Connect the earth wire as
position A.
Connect the thermocouple

Positon 3

Attach leg B ④ to the table top with (3) M5 x 10
bolt
⑱
, attach (2) leg A ③ to the table top with
(6) M5 x 10 bolts
⑱, attach leg C ⑤ with (3)
M5 x 10 bolts
⑱
as illustrated.
Attach the front panel ⑦ to the leg A ③ with
(3) steel flat washers and (3) M6 x 22 bolts
as illustrated.
Note: Remeber to attch cylinder block wire
on front panel ⑦ when tighten the lower end of
leg A ③ with steel flat washer and M6x28
bolt as illustrated.
20
16
21
23
23

Attach (2) side panels ⑧ to legs with
(8) steel falt washers and (8) M6 x 22
bolts ⑳ as illustrated.
23
8X
8X

⑯
Attach cylinder block wire ⑯ to cylinder holder
⑥ and through the front panel ⑦ to the leg A
③ with (1) M5 x 10 bolt ⑱ as illustrated.
Attach cylinder holder ⑥ to 4 legs with (4)
steel flat washers and (4) M6 x 22 bolts
as illustrated.
23 20

Use wrench to scew nut with door
handle ⑰ to the door ⑨, then attach the
door ⑨ to the leg C ⑤ with (4) M4 x 10
f lat bolts as illustrated.
leg C ⑤
24
27 26
Use (1) M4X8 bolt to screw the cover
lid ring ⑪ to the cover lid ⑫.
22

Put the glass beads ⑩ on the burning area of the
table top ①.
Note:
To avoid ignition failure, do not cover the shield
with glass beads. Then place the cover lid ⑫
onto the table top ① when not in use.
WARNING:
Failure to position the parts in accordance with
Failure to position the parts in accordance with
these diagrams or failure to use only parts
specifically approved with this appliance may
result in property damage or personal injury.
15
Step 9
Step 9
glass beads ⑩
table top ①
shield
cover lid ⑫
10

parts
5) If bubbles appear, there is leakage. Turn off the gas tank value.
Loosen and re-tighen the connection. If there is still a leak, please
e-mail to our customer service: [e-mail].
16
12
9

17

18

19

20