Dovre 2000 Series Parts list manual

2000 103.27817.100
INSTALLATIEVOORSCHRIFTEN EN GEBRUIKSAANWIJZING
INSTALLATION ET MODE D’EMPLOI
INSTALLATION INSTRUCTIONS AND OPERATING MANUAL
EINBAUANLEITUNG UND GEBRAUCHSANWEISUNG
INBOUWHAARD / FOYER
FIREPLACE / KAMINEINSATZ
2000-serie (1800; 2700; 2800; 2000S)
1800GL 2000 (2700; 2800) 2000S

2000 303.27817.100
Table of contents pag
Foreword 32
1. Introduction.......................................................................................................................32
2. Safety ...............................................................................................................................32
3. Installation guideline ............................................................................................................33
3.1. Preparatory measures .....................................................................................................33
3.1.1. The chimney........................................................................................................33
3.1.2. Ventilation..........................................................................................................34
3.1.3. Floor, walls..........................................................................................................35
3.1.4. Combustible material round the fireplace ...................................................................36
3.2. Preparation ..................................................................................................................36
3.2.1. Assembly of the legs .............................................................................................36
3.2.2. Assembling the air-controls.....................................................................................36
3.2.2. Assembling the door-closing...................................................................................36
3.2.4. Assembling the flue collar ......................................................................................38
3.3. Installation of the fireplace ..............................................................................................39
3.3.1. Positioning and connection.....................................................................................39
3.3.2. Mounting ............................................................................................................39
3.4. Finishing .....................................................................................................................40
3.5. Packaging materials .......................................................................................................40
4. Instructions for use..............................................................................................................42
4.1. Fuel............................................................................................................................42
4.2. Lighting a fire ...............................................................................................................42
4.3. Burning wood...............................................................................................................43
4.4. Burning coal .................................................................................................................43
4.5. Ash removal .................................................................................................................44
4.6. Extinguishing the fire .....................................................................................................44
4.7. Weather conditions ........................................................................................................44
5. Maintenance.......................................................................................................................44
Annex 1 : Technical data sheet ....................................................................................................58
Annex 2 : Dimensions .................................................................................................................59
Inhalt pag
Vorwort .................................................................................................................................45
1. Einleitung ..........................................................................................................................45
2. Sicherheit ..........................................................................................................................45
3. Montagevorschrift ...............................................................................................................46
3.1. Vorher ........................................................................................................................46
3.1.1. Der Schornstein....................................................................................................46
3.1.2. Lüftung des Räumes..............................................................................................47
3.1.3. Fussboden, Wände ................................................................................................48
3.1.4. Brennbares Material um den Kamin...........................................................................49
3.2. Vorbereitende Arbeiten...................................................................................................49
3.2.1. Montage der Füses................................................................................................50
3.2.2. Montage der Luftregler..........................................................................................50
3.2.3 Montage der Turverschlusses...................................................................................50
3.2.4 Montage der Rauchglocke und des Anschlusskragen.....................................................51
3.2.5. Montage der Drosseleinrichtung ...............................................................................51
3.3. Installation...................................................................................................................52
3.3.1. Aufstellung und Anschluss......................................................................................52
3.3.2. Einbau................................................................................................................52
3.4. Vollendung ..................................................................................................................53
3.5. Verpackungsmaterialien..................................................................................................53
4. Gebrauchsanleitung .............................................................................................................55
4.1. Brennstoff....................................................................................................................55
4.2. Heizen mit Holz ............................................................................................................55
4.3. Heizen mit Kohle..........................................................................................................56
4.4. Geringes Heizen............................................................................................................56
4.5. Aschenbeseitigung .........................................................................................................57
4.6. Auslöschen..................................................................................................................57
4.7. Wetterlage ...................................................................................................................57
5. Wartung ............................................................................................................................57
Anlage 1 : Technischen Daten ......................................................................................................58
Anlage 2 : Abmessungen.............................................................................................................59

2000 3 03.27817.100
Foreword
The Installation Manual and Operators Instructions must accompany this appliance.
As well as instructions for installation and information about use, you will also find
advice concerning safety and maintenance.
Please read this booklet carefully before installation and before firing the unit.
Save this booklet and pass to any subsequent user who can also profit by it.
1.Introduction
Your DOVRE purchase has made you the owner of a high quality product that sym-
bolizes a new generation of energy-saving and ecologically safe heaters, producing
convection heat as well as radiant heat with optimum efficiency. Through the appli-
cation of a revolutionary combustion concept DOVRE heaters achieve astonishing
results in full compliance with strict environmental and safety norms. Also, you will
be enjoying the lovely sight of the fire blazing in the stove.
Our heaters are produced in accordance with ISO 9002, using state-of-the-art pro-
duction means.
In the unlikely event of a malfunction, you can always rely on DOVRE’s after-sales
service.
This heater is designed to be installed in a living room and to be hermetically con-
nected to a flue (chimney).
If the stove is professionally installed, connected to a well-functioning chimney and
sufficiently ventilated, you can take the long-term and trouble-free functioning of
your heater for granted.
Please consult an expert when installing and connecting the heater. The manufac-
turer cannot be held liable for problems caused by faulty installation.
2.Safety
The heating unit is best installed, commissioned, and checked by a competent in-
staller who is aware of national and local legislation.
The heater is designed to heat a room, which means that all surfaces, including the
front glass, can get very hot (> 100 °C).
Please do not place any curtains, clothes, laundry, furniture or other combustible
materials on or near the heater.
It is advised to make a fire in the stove with the highest possible intensity right after
it is installed, so as to cure the heat-resistant paint finish. This may involve some
odour production, which will however disappear after a while.
It is necessary to maintain and regularly clean the stove and the chimney for the
stove to function safely and for a long period of time. Please follow the cleaning in-
structions in the chapter concerned.
In case of a chimney fire, immediately close all air intake vents of the appliance and
alert the fireman.
Broken glass should be replaced before using the heater again.
The stove is specifically designed for burning certain kinds of fuels. In the technical
specifications under cover you can find detailed information concerning this topic. It
is absolutely prohibited to burn fuels other than these, as this may damage your
heater. Moreover, it is ecologically harmful.

2000 4 03.27817.100
3.Installation guideline
3.1. Preparatory measures
The fireplace should be hermetically connected to a well-functioning chimney, suffi-
ciently enclosed to keep combustible materials (floor and walls) at a distance, and
should be installed in a room with sufficientventilation.
Please inform about national or local norms and regulations concerning this subject.
Your distributor will give you the necessary advice.
You can also consult the fire department and/or an insurance company about spe-
cific demands or regulations.
Please read the technical specifications under cover in this manual before installing
the appliance.
3.1.1. The chimney
The chimney (the flue) has a double function:
•It draws air, that is necessary for good combustion, into thestove.
•It functions as an exhaust pipe for combustion gases via thermal or natural
draught. Thermal draught is caused by the difference in heat between the air in-
and outside the flue. The heated air in the flue is lighter than the colder air out-
side the flue and consequently rises up, along with the combustion gases. Natu-
ral draught is caused by environmental phenomena, such as wind.
It is prohibited to connect several heaters to one chimney (for instance the central
heating boiler), unless local or national regulations allow this.
Please check which chimney is to be used for the stove you purchased and whether
your chimney is appropriate for this specific usage. You should consider an expert's
opinion on this matter.
The chimney should meet the following conditions:
•The flue should be made of fireproof material. Ceramic or stainless steel is re-
commended.
•The chimney should be airtight and thoroughly cleaned and should guarantee a
sufficient draught (a draught or negative pressure of 15 to 20 Pa is ideal under
normal circumstances).
•It should run as vertically as possible. Changes in direction or horizontal seg-
ments will disrupt the smoke flow and may cause soot to cumulate inside the
flue (and clog the flue!).
•The chimney's inside dimensions must not be too large in order to prevent the
smoke from cooling off too much. For recommended chimney dimensions, see
the technical specification under cover. Larger dimensions can be used if the flue
is well insulated.
•The flue's diameter should be the same throughout its whole length. Wider, or
especially narrower segments will disrupt the smoke flow and are best avoided.

2000 5 03.27817.100
The same is true for a cover plate or exhaust hood on top of the chimney. The
exhaust hood must not narrow the chimney's outletand should be designed in a
way that wind will not hinder, but promote the smoke flow.
•Especially if the flue runs through unheated rooms or outside the house, further
insulation is necessary. Metal chimneys, or parts of the chimney outside heated
rooms should always have double-walled, insulated flues. The part of the chim-
ney outside the roof should always be insulated.
•The chimney should be high enough (at least four metres) and should end in a
zone that is clear of nearby buildings, trees or other obstacles. The rule of
thumb here is: 60 cm above the ridge of the roof. If the distance between the
ridge and the chimney measures more than three metres, see the dimensions
stipulated in the illustration below. Depending on the presence of nearby build-
ings or trees, the chimney should be higher.
3.1.2. Ventilation
The burning of wood, charcoal or gas involves oxygen consumption. It is of the ut-
most importance that the room in which the stove is installed should be sufficiently
ventilated.
Insufficient ventilation may disrupt the combustion process and cause the smoke
flow through the chimney to be interrupted, which may lead to smoke emissions
into the room. Mainly in case of a fireplace, together with the combustion gases, lots
of room air will be extracted through the chimney; that makes supply of sufficient
fresh air and ventilation extremely important.
If necessary, you can install a ventilation grille to provide a constant flow of fresh air
in the room. This precaution is particularly necessary in well-insulated rooms with
mechanicalventilation.
The DOVRE fireplace has been designed to produce most heat by means of convec-
tion. Heat is mainly transmitted through the back panel, the lateral panels, and the
smoke dome. Both the material (cast iron) and shape (increased heating surface by
means of corrugation) improve heat transmission to the surrounding air. As this air
is heated, it will rise and a natural hot air flow, i.e. convection, will develop. Up to
your choice, that hot air may be led to thesame room or to another room.
For optimal heating and leading the convection air, the airflow must not encounter
any obstacles. Hence, it is important that there is enough space between the fire-
place and the surrounding material, and that the inlet and outlet area of convection
air are sufficiently large.
min 0.5 m
3m
min1m
highest point of the roof
within a distance of 3 m.
3 m
min0.5m

2000 6 03.27817.100
Convection air may be led to arrive from both
the room and outside (other room, cellar, exte-
rior) to the bottom side of the fireplace. In case
convection air is supplied (directly or indirectly)
from outside, it may also be useful as a supply
of fresh air for combustion.
At any rate, assure proper home air manage-
ment and sufficient air supply into the room.
Ensure not to use other air-consuming appli-
ances, such as heaters, cooking hoods, bath-
room ventilators, in the same room or in the
house while the stove is burning; or make sure
to have an extra ventilation grille installed for
these appliances.
3.1.3. Floor, walls
Combustible material must be sufficiently protected. The floor under the fireplace
and the walls around it must not contain electric wires.
The appliance shall be installed on floors with an adequate load-bearingcapacity.
Under the appliance
Under the appliance, any combustible material must be removed or specially
shielded by means of a 6 cm concrete slab and 10 cm insulation.
Floor round the appliance
A floor made of combustible material must be properly shielded in the following
areas:
Front: height of the lower part of the fire chamber + 30 cm, but 60 cm at least.
Sides: height of the lower part of the fire chamber + 20 cm, but 40 cm at least.
V > H + 30 > 60
S > H + 20 > 40

2000 7 03.27817.100
3.2. Preparation
Please inspect the fireplace for damage caused during transport immediately after
delivery and notify your distributor in case there are any defects. Do not put the ap-
pliance into operation in the meantime.
In order to avoid damaging the fireplace during installation and to make its handling
easier, it is recommended to remove previously all loose parts (fire-resistant bricks,
grille, ashtray, ...) from the stove. Note the location of those parts while removing
them, so that you have no difficulties in re-assembling the parts later on.
3.2.1.Assembling the legs
Seesketch.
3.2.2. Assembling the air-controls
Seesketch.
3.2.3. Assembling of the door-closing
Walls, ceiling
Combustible walls behind, next to, or above the fireplace must be shielded with at
least a 10 cm stone or brick wall and 10 cm insulation. Fireproof materials should be
covered with at least 6 cm insulation.
3.1.4. Combustiblematerialround the fireplace
Within the radiation area of the fireplace
Assure a distance of at least 80 cm between the opening of the fireplace and com-
bustible material. That distance may be reduced to 40 cm if the combustible mate-
rial is sufficiently shielded and well ventilated.
Outside the radiation area of the fireplace
Assure a distance of at least 5 cm between the mantle built around the fireplace and
combustible material. A small surface contact between
combustible material and the mantle (e.g. wall cladding) is
allowed if the mantle of the fireplace is sufficiently insu-
lated.
A wooden ornamental rafter must not be installed within
the radiation area of the fire. Outside the radiation area,
there must always be a ventilation gap of 1 cm all around
to prevent heat from building up (see picture).
No combustible material must be present within 50 cm
from the convection outlet areas.
min1cm
min1cm

2000 8 03.27817.100
2000S

2000 9 03.27817.100
3.2.4. Assembling the flue collar
Fix the flue collar on the smoke dome with bolts, nuts and collars. Assure
proper sealing with kit or paste.

2000 10 03.27817.100
3.3. Installation of the fireplace
3.3.1. Positioning and connection
Put the fireplace at proper
height. Make sure that it is
stable and level and that the
side panels are perpendicular
to the bottom plate. Put the
fireplace far enough from the
walls, so that minimum 10
cm of free air passage re-
mains between the back of
the fireplace and the wall af-
ter adding the necessary in-
sulation.
Make an airtight connection
between fireplace and chim-
ney, according to good practice.
Before further installation of the fireplace, check for sufficient draft in the chimney
and for proper connection between the smoke duct and the appliance.
For that purpose, you can light a small intense fire with paper and small dry kindle.
In case of a brick smoke duct, wait until the duct is dry enough.
3.3.2. Mounting
Start with the masonry round the base of the fireplace. In that masonry, the air sup-
ply grids (optional) will be installed. Minimum air supply opening is 400 cm² (1800:
350 cm²). The grids may be installed on all sides.
It is important that air flows freely into the convection chamber. If you use an air
vent (to convey outside air into the convection chamber), remember to build in the
adjustment knob.
It is recommended to cover the inner side of the convection
chamber with extra reflecting insulation material. That pre-
vents loss of heat radiation to outside walls or adjacent
rooms, as well as deterioration of any inside wall insulation.
Make sure that the doors of the hearth move freely over the
plate in front of the fireplace.
Continue building the chimney up to the smoke dome. Assure
a gap of at least 2 mm between the fireplace and the masonry
to allow for dilatation of the fireplace. If necessary, use heat-resistantstrips.
Upper structure support
The masonry over the fireplace must not rest on the fireplace. That is why a support
is used. Between the steel support and the smoke dome, you must leave a free
space of at least 3 mm. That will prevent tensions in the material that might tear the
upper structure. The steel support may rest on the side structure or be attached to
the wall by means of threaded rods.

2000 11 03.27817.100
Convection chamber:
The convection chamber topside must be airtight. For that purpose, you can use a
cover of steel, concrete, or any other fire-resistant material, and put extra insulation
on top of it. Make sure that the cover is well horizontally placed.
The cover must be installed at 30 cm at least above the smoke dome. The outlet
grids must be installed straight under that cover. Make sure that convection outlet
area is big enough: minimum 500 cm².
In the convection chamber no combustible material must be used. Make sure that,
when using other auxiliary material such as steel, it will not function as a heat
bridge.
The picture on the next page shows an example of fireplace installation within
combustible
3.4. Finishing
When the appliance is installed in the right place, its connection with the chimney
made airtight, and the masonry mantle completely mounted, all loose parts are in-
stalled in the appliance.
Your fireplace is now ready to be used.
Depending on the materials used for mounting, it is recommended to wait for some
time until all masonry is dry before lighting a fire.
Attention: never light a fire with the inner plates or refractory stones removed.
3.5. Packaging materials
Packaging materials should be disposed of in a responsible way and in accordance
with governmental regulations.

2000 12 03.27817.100
Chimney
Refractory cement
or special con-
ne ctor
Insulation
(min 10 cm)
Fireproof wall min
10 cm
Combustible wall
Convection area
Fresh air inlet
Fireproof floor Combustible floor
Convection
air inlet
Insulation
(if necessary)
Convection
Air outlet
Opening against
eventual pressure
buildup
Stainless steel
pipe
Insulation
Combust i-
ble ceiling
Fireproof ce i-
ling
Cover plate
Example of fireplace installation within combustible material

2000 13 03.27817.100
4.Instructions for use
4.1. Fuel
The only suitable fuels for this stove are wood, brown coal briquettes and charcoal
(only for 2000S). No other fuels are allowed to be burnt, as they can inflict serious
damage to your stove.
Do not burn any treated wood either, such as scrap wood, dyed wood, impregnated
or preserved wood, plywood or chipboard. The fumes of these, as of synthetic mate-
rials, old papers and household waste, are highly polluting for both your stove and
your chimney, and for the environment. Theyalsocould causechimney fires.
Wood
Hard woods, such as oak, birch-and fruit-trees, are the ideal fuels for your stove.
The wood must have dried for at least two years in a covered and well-ventilated
place. Split logs will dry faster. Dry wood should contain no more than twenty per-
cent moisture.
Wet logs are unsuitable for burning, as they do not produce enough heat and all of
the energy is lost in the process of evaporation. Moreover, the burning of wet wood
causes badly smelling gases to be released and a thick layer of tar will deposit on
the stove panels and in the chimney.
Browncoalbriquettes
Brown coal briquettes burn in more or less the same way aswood does. You should
only burn briquettes on a bed of charcoal in your stove.
Charcoal
There are several categories of anthracite coal. Some characteristics may be legally
determined. For instance anthracite “A” has to contain less than 10% of volatile sub-
stances, anthracite “B” less than 12%. The ash content may range from 3 to 13%.
For a good operation of your appliance, the use of anthracite “A” with a low ash con-
tent is recommended. A combustible with a high ash content has a lower net heating
value. Moreover, the ashes have to be removed more frequently and the fire will go
out faster. The recommended calibre is 12/22 or 20/30.
4.2. Lighting a fire
In order to create sufficient draught and to prevent smoke from being emitted into
the room, the chimney should be warm enough before lighting a fire. A cold chim-
ney can be heated up by lighting a ball of paper above the fire plate.
To kindle the fire in the stove you can use paper and/or firelighters and small pieces
of wood.
Slightly open the door and pull the air slides wide open.
It is important that the kindled fire should burn intensely. You can then throw larger
pieces of wood onto the fire, and close the doors. When the fire has stabilized and is
glowing enough, you can put the logs, the charcoal or the brown coal briquettes on
the fire.

2000 14 03.27817.100
4.3. Burning wood
The best way to control the fire is to completely close the lower air slide, which you
use to get the fire started, and to regulate the air supply with the upper air slide
only (not for 1800). In case the air supply through the upper slide seems insuffi-
cient, or if you would like to fan the fire, you can partially open the lower air slide
for a while.
Always keep the stove doors tightly closed. Never let the doors open when the fire is
burning.
Add extra fuel when necessary. Never add too much fuel. It is best to fill the stove
for one third and to top it up on a regular basis.
Always open the filling door slowly and for a short space of time. Before filling up,
the charcoal bed should be carefully spread open. Check whether the coals are glow-
ing enough just behind the log retainer, so that the added fuel will immediately
catch fire. If necessary you can open the lowerair slide for a while.
Open stacking will make the logs burn very intensely, as the oxygen can easily reach
every part of the fire. This
method of stacking is applied
when burning wood for a short
while. Compact stacking will
make the fire burn slower, as the
air can only reach the outer parts
of the fire. This stacking method
is best used when burning for a
longer while.
Low intensity fires cause tar and
creosote to deposit in the chim-
ney after a long period of time.
Tar and creosote are highly com-
bustible substances. Thicker lay-
ers of these substances might catch fire when the temperature in the chimney in-
creases suddenly and steeply. Therefore it is necessary for the fire to regularly burn
very intensely, so that thin layers of tar and creosote immediately disappear.
Low intensity fires also cause tar to deposit on the stove panes and doors.
When it is not too cold outside it is better to let the stove burn intensely for just a
few hours a day.
4.4. Burning coal (only for 2000S)
WHEN BURNING CHARCOAL THE AIR SLIDE ABOVE MUST ALWAYS BE KEPT CLOSED.
For burning coal, you need the coal-basket.
As soon as the fire is sufficiently stable and there is enough glow, the first shovel of
coals can be put onto the fire. Complete the filling once the coals have caught fire.
Make sure you do not quench the fire by putting too much coals onto it at a time.
Once the fire has burned for a while, adjust the air slide at the bottom of the door.
Before adding some extra coals, open the air slide below completely. Use the shaker
grate or the supplied shovel, and shake till the glowing parts fall into the ash plate;
then add the coals. After a few minutes, adjust the air slide. Add some more coals
until you can only see the glow of the previous filling.
When the fire basket or the cast-iron plate fins are red-hot, you are heating too in-
tensely.
open stacking compact stacking

2000 15 03.27817.100
4.5. Ash removal
If your fireplace is equipped with an ashtray
it must be emptied before the ashes reach
the lower edge of the combustion grid. With
the cold handle supplied, you can tilt the
grid upwards and remove the ashtray from
the device.
Relatively speaking, burning wood pro-
duces little ash and it will not be necessary
to remove it each time daily. Moreover,
wood burns better on a bed of ash.
4.6. Extinguishing the fire
Stop fuelling the fire and let it burn out.
Damping a fire by closing the air slides involves the release of noxious gases. You
should let the fire burn out and keep an eye on it as long as it is still glowing.
4.7. Weather conditions
Attention!
Mist and heavy fog will block the chimney's smoke outlet and may lead to smoke
emissions into the living room.
It is best not to use the fireplace under these weather conditions.
5.Maintenance
It takes only little effort to keep your appliance in good condition.
Regularly check whether the sealing cord still closes the doors tightly enough.
Minor paint damage can be touched up with a can of spray paint. Your dealer can
supply you with the correct spray product.
During the first use after repainting your unit might give off some slight odour.
However, this will disappear quickly.
The glass can be cleaned with a number of glass cleaning products available on the
market. Your installer can also supply you with appropriate products. However,
never use abrasive or corrosive cleaning products.
At the end of the heating season, seal off the chimney with a ball of paper. You can
then thoroughly clean the stove on the inside.
If necessary, replace the sealing ropes and use fire cement to fill up possible leaks.
Remove the fireplate for better and more thorough cleaning.
To remove the doors, disassemble the hinges as shown.
You should have your chimney swept by an expert before the heating season begins.
It is useful to check the chimney for soot during the heating season as well. Check-
ing and maintaining the chimney is a statutory requirement.
When all of the above advice is heeded, you will be able to fully enjoy your stove.
2000

2000 16 03.27817.100
Bijlage 1: technische gegevens / Annexe 1: données techniques / Annex1: technical data sheet / Anlage 1: technischen Daten
Model / Modèle / Modell 2000S 2000 1800 Nominaal vermogen Puissance nominale Nominal heat output Nominalleistung
11 kW
11 kW
8 kW
Aanbevolen brandstoffen Combustibles conseillés Advised combustibles Empfohlene Brennstoffe
Hout Bois Wood Holz
Bruinkool lignite Browncoal Braunkohl
Kolen Charbon Coal Kohlen
Hout Bois Wood Holz
Hout Bois Wood Holz
Bruinkool lignite Browncoal Braunkohl
Hout Bois Wood Holz
Hout Bois Wood Holz
Bruinkool lignite Browncoal Braunkohl
Deuren Portes Doors Feuerraum
Gesloten Fermé Closed Geschlossen
Gesloten Fermé Closed Geschlossen
Gesloten Fermé Closed Geschlossen
Open Ouvert Open Geöffnet
Gesloten Fermé Closed Geschlossen
Gesloten Fermé Closed Geschlossen
Open Ouvert Open Geöffnet
Gesloten Fermé Closed Geschlossen
Gesloten Fermé Closed Geschlossen
Schoorsteenaansluiting Raccordement cheminée Flue connection Schornsteinanschluss
200 mm
200 mm 150 mm
Massadebiet van rookgassen Débit des fumées Flue gas mass flow Abgasmassenstrom)
7.3 g/s
9.9 g/s
12.4 g/s
31.7 g/s
9.1 g/s
9.5 g/s
32.2 g/s
7.0 g/s
6.7 g/s
Rookgastemperatuur Température des fumées Flue gas temperature Abgasstutzentemperatuur
414 °C
343 °C
360 °C
248 °C
387 °C
380 °C
246 °C
392 °C
364 °C
Minimum trek Dépressionminimal Minimum draught Mindesförderdruck
0.14 mbar
0.14 mbar
0.10mbar
0.10 mbar
0.12 mbar
0.10 mbar
0.10 mbar
0.15 mbar
0.15 mbar
Gewicht / Poids / Weight 165 kg 130 kg 75kg
Hout Bois Wood Holz Open Ouvert Open Geöffnet 35.8 g/s 250 °C 0.10 mbar
% CO 0.10 % < 0.10 % < 0.1 % 0.10 % 0.2 % Rendement / Rendement/ Efficiency / Wirkungsgrad 79.4 % 78 % 70.4 % 76.7 % 75.7 % 74.6 % 75.1 %

2000 17 03.27817.100
Annex 2 :dimensions
Anlage 2 :Abmessungen
Bijlage 2:afmetingen
2000S

2000 18 03.27817.100
2000

2000 19 03.27817.100
1800

2000 20 03.27817.100
2800VG