Dovre VIRTUS 50GA Parts list manual

INSTALLATIEVOORSCHRIFTEN EN GEBRUIKSAANWIJZING GASKACHEL
INSTALLATION INSTRUCTIONS AND OPERATING MANUAL GASSTOVE
INSTALLATION ET MODE D’EMPLOI POELE A GAZ
EINBAUANLEITUNG UND GEBRAUCHSANWEISUNG GASOFEN
INSTRUCCIONES DE INSTALACIÓN Y USO ESTUFA DE GAS
VIRTUS 50GA
VIRTUS 70GA
DOVRE
03.28304.100 - 03/2019
C11/C31/C91

DOVRE
2Subject to change because of technical improvements
Table of contents
Introduction 3
Declaration of conformity 4
Safety 4
Installation requirements 5
General 5
Concentric flue gas exhaust system 5
Existing chimney Type C91 6
Floor and walls 6
Product description 7
Installation 7
General preparation 7
Preparing the connection to the flue 9
Closed system connection 9
Establishing a gas connection 13
Installing the remote control set 13
Placing decorative wood block set 14
Use 16
First use 16
Operating instructions 16
Manual operation 25
Switch off gas to stove 26
Combustion control 26
Resolving problems 26
Maintenance 26
Annual maintenance for the appliance 26
Cleaning and other regularly maintenance 27
Spare parts 28
Appendix 1: Technical data 29
Appendix 2: Dimensions 33
Appendix 3: Distance from combustible
material 35
Appendix 4: Overview of concentric flue gas
exhaust materials 37
Appendix 5: Calculation sheet for checking
projected route 38
Appendix 6: Diagnosis diagram 39
Index 41

DOVRE
Subject to change because of technical improvements 3
Introduction
Dear user,
By purchasing this heating appliance from DOVRE
you have selected a quality product. This product is
part of a new generation of energy-efficient and envir-
onmentally-friendly heating appliances. These appli-
ances make optimum use of convection heat as well
as radiation heat.
Your DOVRE appliance has been manufactured
with state-of-the-art production equipment. In the
unlikely event of a malfunction, you can always
rely on DOVRE for support and service.
The appliance should not be modified; please
always use original parts.
The appliance is intended for use in a living room. It
must be hermetically connected to a properly work-
ing flue.
We advise you have the appliance installed by an
authorized and competent installer.
DOVRE cannot be held liable for any problems or
damage resulting from incorrect installation.
Observe the following safety regulations when
installing and using the appliance.
In this manual, you can read how the DOVRE heating
appliance can be installed, used and maintained
safely. Should you require additional information or
technical data, or should you experience an install-
ation problem, please first contact your supplier.
© 2019 DOVRE NV

DOVRE
4Subject to change because of technical improvements
Declaration of
conformity
Notified body: 0359
The undersigned
Dovre NV, Nijverheidsstraat 18 B-2381 Weelde,
hereby declares that the VIRTUS 50GA (P) / 70GA(P)
gas stove has been produced in accordance with EN
613.
Weelde 01-03-2019
Due to continuous product improvement, the spe-
cifications of the appliance supplied can vary from the
description in this brochure without prior notice.
DOVRE N.V.
Nijverheidsstraat 18 Tel : [phone]
B-2381 Weelde Fax : [phone]
Belgium E-mail : [e-mail]
Safety
Please note: All safety regulations must be
complied with strictly.
Please read carefully the instructions supplied
with the appliance for installation, use and
maintenance before using the appliance.
The appliance must be installed in accordance
with the legislation and requirements applic-
able in your country.
All local regulations and the regulations relating
to national and European standards must be
observed when installing the appliance.
The appliance must be placed, connected,
commissioned and inspected by an authorized
installer, in accordance with the current
national and local standards, in accordance
with regulations for closed appliances and in
accordance with the installation instructions of
the manufacturer.
The appliance is designed for heating pur-
poses. All surfaces, including the glass and the
connecting pipe, can become very hot (more
than 100°C)! This must be regarded as an act-
ive zone. Make sure there is sufficient pro-
tection if young children, disabled persons or
old people are in the vicinity of the appliance.
Safety distances from flammable materials
must be strictly adhered to.
Do not place any curtains, clothes, laundry or
other combustible materials on or near the appli-
ance. The minimum safe distance is 80 cm.
When in use, do not use flammable or explos-
ive substances in the vicinity of the appliance.
If the glass in the appliance is broken or
cracked, it must be replaced before you can
use the appliance again.
The appliance has been set and sealed in the
factory, in accordance with the category stated
on the model plate and at the correct nominal
load. Check that the information on the model
plate corresponds with the local gas type and
pressure, and with the nature of your install-
ation.

DOVRE
Subject to change because of technical improvements 5
The model plate is behind the door at the bot-
tom in the appliance.
The appliance must be inspected by the
installer for the air tightness of the gas supply
and flue gas duct. The operation of the control
valve, the thermocouple circuit and the ignition
of the burner must also be checked.
When the appliance is ready for use, have your
installer tell you about its use, operation and
maintenance.
Use only the supplied ceramic wood block set,
coals or stones.
Place the log set exactly according to the
description.
Keep the area around the pilot flame free of
coal.
Avoid dirt in the gas pipe.
Always close the gas valve if the appliance is
not in use.
If you notice a gas smell, immediately close
the main valve, open windows and avoid fire or
the use of electrical contacts, such as
switches, because of the sparks they can
cause. Always call in an expert to trace a pos-
sible gas leak.
Installation
requirements
General
The appliance must be connected tightly to a well-
functioning flue.
For connection measurements: see "Technical
data" appendix.
Ask the fire service and/or your insurance com-
pany about any specific requirements and reg-
ulations.
Concentric flue gas exhaust
system
This closed gas stove was designed in combination
with a concentric flue gas exhaust system from the
manufacturer Muelink & Grol. The appliance can also
be connected to a concentric flue gas exhaust system
from the manufacturers Metaloterm or Poujoulat. Use
the appropriate connection collar (available from your
supplier) and follow the supplier's instructions for the
installation.
Use only original parts from the manufacturers
named above. You can order the elements for the
concentric pipe system (such as wall sleeves, roof
sleeves, tubes and bends, clip bindings and brack-
ets) in the desired quantities via your supplier.
You can find the order codes of the available
elements in the appendix "Materials list for con-
centric flue gas exhaust".
The appliance may not be connected to an existing
flue gas exhaust duct or chimney just like that. An
existing chimney or flue gas exhaust duct can be
used as an active element in the installation under
certain conditions. See the paragraph "Existing
chimney duct".
The appliance has a closed combustion chamber
and must be installed as a closed appliance of type
C11-C31 (depending on the choice of wall or roof
sleeve). With a combined intake-exhaust, the nat-
ural draught of the appliance removes the com-
bustion gases outside. The same natural draught
sucks in the necessary combustion air. The con-
centric flue gas exhaust system can be equipped
with a wall sleeve or a roof sleeve. Use the pre-
scribed wall outlet or roof outlet for this purpose.
A maximum value of 12 metres applies to the total
allowable length of the pipe system (the resistance
length). Every bend of 90° corresponds to 1 metre
of resistance length and every bend up to 45° cor-
responds to 0.5 metres of resistance length.
The horizontal section of the pipe system may
never be longer than the vertical section.
In order to maintain the natural draught, at least one
metre of concentric pipe must be placed vertically
before the wall or roof sleeve is installed.
Before the appliance can be placed, you must
check whether the pipe route desired for your
installation is technically permitted. See the
appendix “Calculation sheet for checking pro-
jected route”.

DOVRE
6Subject to change because of technical improvements
The distance from ducts and sleeves to com-
bustible material must be at least 50 mm every-
where.
All elements of the air supply and the flue gas
exhaust system must be inserted at least 30 mm
into each other and be secured against coming
loose using clip bindings.
The duct must be kept in its position by means of
wall brackets and centring plates. The maximum
distance between the wall brackets is 2 metres.
The flue gas exhaust system and the outlet must
satisfy any local regulations that apply. This is a
closed appliance of type C11 or C31 (depending on
the choice of wall or roof sleeve).
The flue must end in a zone that is not affected by
surrounding buildings, trees close by or other
obstacles.
For outlets that are in the vicinity of a boundary par-
tition or ventilation opening, see the national and
regional regulations regarding this.
In the case of a wall sleeve, the outlet must be in a
zone such that any contact between flue gas outlet
and/or flue gases and people is impossible and
such that the flue gases cannot accumulate under
overhanging parts of buildings or awnings or such
like.
The flue gas outlet can reach temperatures of
200 °C, while the flue gases can reach 300 °C.
Existing chimney
Type C91
An existing flue gas pipe (chimney) can be converted
into a concentric flue gas exhaust system.
In this case, the following requirements apply to the
existing chimney:
The existing pipe must be leakproof and thoroughly
cleaned.
The pipe must be able to withstand temperatures
up to 600°C along its entire length.
The pipe may change direction no more than one
time, with a maximum change angle of 45° and
along no more than 25% of the total length.
The pipe must have a diameter of at least 150 mm
round or square, and no more than 250 mm round or
square along the entire length. The section may not
be larger or smaller than the specified limits at any
place. The section may vary over the whole length
of the flue pipe on the condition that the transitions
in section occur gradually.
If this last condition cannot be satisfied, the pipe
may be lined with stainless steel flexible piping
with a diameter of 150 to 250 mm, which is heat-
resistant to 600°C before it can be converted into
an air intake pipe.
The flue pipe must be closed at the top and bottom
with the recommended flanges (mounting plates).
The bottom of the flue section must always be con-
nected to the appliance using a concentric duct sec-
tion and the prescribed roof outlet must always be
mounted on the outlet side.
The maximum allowable length, including the con-
nection section (resistance length), is 12 metres.
Every elbow of 90° corresponds to 1 metre of res-
istance length and every elbow up to 45° cor-
responds to 0.5 metres of resistance length.
Floor and walls
The floor on which the appliance is placed must have
sufficient bearing capacity. The weight of the appli-
ance is given in the appendix “Technical Data
appendix”.
Keep sufficient distance between the appli-
ance and combustible materials such as
wooden walls and furniture.
Carpets and rugs must be at least 80cm away
from the fire.
For further requirements with respect to fire
safety, see the appendix "Distance from com-
bustible material".

DOVRE
Subject to change because of technical improvements 7
Product description
5
1
3
4
2
6
09-20022-055
1. Glass pane
2. Ceramic wood block set
3. Burner
4. Valve to gas block
5. Gas connection G3/8"
6. Concentric smoke removal above or behind
76 5
12 43 5
09-20022-041
1. Knurled screws for cover
2. Cover of gas controls
3. Receiver
4. Gas block
5. Reset button
6. Battery cover
7. Batteries
Features of the appliance
The VIRTUS GA(P) is a standalone closed gas
stove. A closed apparatus does not draw the com-
bustion air from the room in which the stove is
placed but uses outside air. The stove is con-
nected to a combined air intake/flue gas exhaust
system. The stove can be connected to a C11, C1
or C91-type chimney system. The stove is fitted
with a Muelink & Grol connection collar for con-
centric ducts. Thanks to this concept, the stove is
suitable for the use in crack-free and well-insulated
homes.
Delivery of the stove includes a battery-operated
wireless remote control with thermostat.
The appliance comes with electronic ignition.
The appliance is supplied with a natural-looking
wood block set made of ceramic material.
Installation
General preparation
Please check the appliance immediately after deliv-
ery for damage during transport or any other dam-
age or defects. The appliance is attached to the
pallet with screws at the bottom.
1
2
3
4
10
09-20022-042
If you detect transport damage or any other
damage or defects, do not use the appliance
and notify the supplier.
Remove the detachable parts from the appliance
before you begin its installation.

DOVRE
8Subject to change because of technical improvements
It is easier to move the appliance and to avoid
damage if the removable parts have been
removed.
Note the location of the removable parts, so
that you can re-position the parts in the correct
place later on.
The appliance can be opened by first removing the top
plate (1) and then the cast-iron front (2) by lifting this
upwards in order to remove it from its projections.
09-20022-043
1
2
The glass pane (4) can be removed by loosening the
screws of the bottom glazing bead (1) (these must not
be removed), and then loosening the screws (2) of the
top glass fixings (3).
Placing the stove
Preferably place the stove on a flat floor. The appli-
ance is fitted with adjustable feet in the floor plate
so that the appliance can be adjusted and made per-
fectly level.
Take the distance from combustible material into
account. See the appendix "Distance from com-
bustible material".
Determining the duct route
Make a drawing of the route you want the concentric
exhaust duct to follow.
Check whether the duct route you want is per-
mitted from a technical point of view based on the
appendix “Calculation sheet for checking projected
route”. If this is not the case, you must decide on
an alternative route that is within the limits per-
mitted.
Decide on the type and number of the parts
required. Use the appendix “Overview of con-
centric flue gas exhaust materials” for this.
Attaching a restriction plate
Depending on the route selected and the ratio
between vertical and horizontal length, a restriction
plate must be attached to the stove at the right place
and in the right position. To adjust the restriction plate
properly, you should first remove the baffle plate; see
the following figure.
PH2
09-20022-045
Positioning the restriction plate serves to
adjust the draft in the stove to the duct route
selected.
The restriction plate has three settings.
Position 1: Restriction plate maximally open,
Position 2: Restriction plate in neutral position,
Position 3: Restriction plate minimally open
(50mm). See following figure. If you decided on a
permitted duct route, the correct position for the
restriction plate follows from the appendix “Cal-
culation sheet for checking projected route”.

DOVRE
Subject to change because of technical improvements 9
3 2 1
09-20022-046
Preparing the connection to
the flue
When connecting the stove to the flue, you can
choose to connect to the top or to the back of the
stove.
Connecting to the top
The stove is ready to be connected at the top upon
delivery.
When a pipe system from a manufacturer other
than Muelink & Grol is used, first use the
adapter belonging to that manufacturer’s pipe
system.
Connecting to the back
1. Remove the top plate.
2. Remove the heat shield (A) and break out the
cover.
09-20022-052
3. Remove cover plate (B) and its seal (3) on the
back.
4. Remove cover plate (C) and its seal (3) on the
back internally.
5. Remove the outer collar (1) and its seal (3) at the
top.
6. Remove the inner collar (2) and its seal (3).
7. Fit the inner collar (2) and the outer collar (3) with
their respective seals (3) to the back of the appli-
ance.
8. Fit the cover plates (B) and (C) and their respect-
ive seals (3) to the top of the appliance.
9. Replace the heat shield (A).
10. Fit the top plate.
1
3
2
4
4
A
B
3 C 3
PH2
09-20022-049
Closed system connection
The concentric exhaust system allows for a series of
connection options for this appliance:
Through the facade, at any height, with or without
horizontal or oblique joint.
Through the roof, with or without horizontal or
oblique joint.
Through an existing flue gas exhaust pipe (chim-
ney)
First place the stove, see section “General pre-
paration”. The concentric duct system can then be put
together in steps, starting at the stove.

DOVRE
10 Subject to change because of technical improvements
Facade sleeve through a facade of
non-flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
The following illustration shows the situation of a fin-
ished facade sleeve.
09-20022-047
1. Start at the stove and add the concentric pipes
one component at a time along the route you
decided on in advance.
2. Next, install a concentric elbow and possible hori-
zontal change in direction and decide on the loc-
ation of the sleeve.
3. Make a 10 mm larger hole in the facade in such a
way that the air intake duct drains to the outside.
Use a 1 - 3 degree angle or a slope percentage of 2
-5% for this.
Prevent dust and/or grit from getting into the
stove when drilling.
4. Decide on the length of the facade sleeve and
shorten the intake to the wall if necessary. Allow
the flue gas duct to extend approximately 10 mm
from the air intake duct.
Use tin-snips to shorten the air intake cover
(0.5 mm).
Use a hacksaw to shorten the flue gas duct
(0.6 mm).
Grinding is not recommended as it burns stain-
less steel.
5. Remove burrs and sawdust.
6. Extend the facade sleeve through the facade from
the outside, with the “TOP” up, connect to the con-
centric elbow and attach it to the outside of the
facade (make sure the air intake cover drains to
the outside).
7. If so desired, the hole on the inside of the wall can
be finished with a wall plate.
Facade sleeve through facade of
flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Follow instruction steps 1 and 2 in the preceding
section.
2. Make a hole in the facade in such a way that the
sleeve is and remains at least 50 mm away from
flammable material all around. This can be done in
the following two ways; see the illustration below.
a. Use a protective duct (1) of non-flammable
material with a diameter of 250 mm.
b. Make a tube (2) of non-flammable material,
250 mm square.
Prevent dust and/or grit from getting into the
stove when drilling.

DOVRE
Subject to change because of technical improvements 11
3. Follow instruction steps 4, 5 and 6 in the preceding
section.
4. Always use centering plates (3) to center and fin-
ish the facade sleeve.
Converting an existing chimney
pipe
If the home already has a chimney, you can lead the
concentric duct system through the existing chimney
pipe. You can also convert the existing pipe into a con-
centric pipe using a single-wall flexible hose and the
right pipe reducers. There is a conversion kit for this.
See the chapter “Installation requirements” for the con-
ditions under which this conversion is permitted.
The following parts are required to convert an existing
flue into a closed system; see next figure.
6
9
10
11
8
4
2
7
5
5
3
1
09-20022-048
1 The hearth or stove to be connected
2 Concentric duct, 100/150 mm, modular
3 Installation plate inside, square 300 mm
4 Single-wall slide, round diameter 97 mm
5 Parker screws (4 pc)
6
Flexible stainless steel 316L hose, single-
wall round diameter 100/107 mm (heat res-
istance 600°C)
7Stainless steel hose clamp reach diameter
90 to 165 mm
8 Existing chimney or flue pipe
9 Installation plate outside, square 300 mm
10 Clamping strap (included in delivery of part
11)
11 Roof sleeve
The conversion set consists of parts 3, 4, 5, 7 and 9.

DOVRE
12 Subject to change because of technical improvements
Follow the instructions below for assembly and see
the figure above.
1. Lead the flexible hose (6) through the existing pipe
(8).
2. Attach the slide (4) to the lower end of the flexible
hose and secure it with two Parker screws (5).
3. Keep the bottom of the slide even with the bottom
of the pipe or the ceiling. Cut the flexible hose at
approximately 100 mm above the chimney cap.
4. Attach the installation plate-outside (9) to the flex-
ible hose, clamp it with a hose clamp (7) and
secure it all with a Parker screw (5).
5. Attach the installation plate-outside (9) watertight
to the chimney cap with silicon sealant and stain-
less steel screws.
6. Install the roof sleeve (11) and secure it with the
clamping strap included in the delivery (10).
After the roof sleeve is installed, the slide (4)
should extend about 100 mm under the pipe or
ceiling.
7. Attach the installation plate-inside (3) gastight on
the bottom of the flue or on the bottom of the ceil-
ing with silicon sealant and stainless steel
screws.
8. Place the stove (1) as indicated in the chapter
“Installation requirements”.
9. Connect the stove with the lower end of the flue
using concentric components (2). All components
must overlap at least 30 mm and be secured with
clamping straps or stainless steel Parker screws
to prevent them from coming apart. Extend the
concentric pipe at least 100 mm into the existing
flue.
The slide (4) should therefore extend about 200
mm into the inner duct of the top concentric
component. If this is not the case, the flexible
hose (6) will be kinked in the chimney, pre-
venting the system from functioning properly.
11. Finally, install the clamp strap in the installation
plate-inside (3).
Roof sleeve through a flat roof of
flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Start at the stove and add the concentric pipes
one at a time, including the changes in direction
you want, along the route you decided on in
advance, up to just under the roof.
2. Decide on the location for the roof sleeve.
3. Make a hole with a 250 mm diameter, so that a fire
separation of 50 mm remains round the pipe.
4. Attach a square installation plate (of at least 300
mm and with a sufficiently large centered round
hole) (1) or 2 centering plates with screws to the
bottom of the roof partition to center the pipe; see
following figure.
5. Insert a clamping strap (2) in the installation plate
by first turning it in and then out.
6. Extend the concentric pipe (3) until it extends at
least 400 mm above the roof surface (more is per-
mitted up to a maximum of 1000 mm stand-alone).
7. Slide the roof sheet (4) over the pipe and tighten it
with screws.
8. Finish the seam between the pipe and the cone of
the roof sheet or lead slab watertight with silicon
sealant and if necessary a storm collar (5).
9. Install the roof sleeve (6) and secure it with the
clamping strap included in the delivery.
10. Make sure the roof sheet is covered watertight.
Use lead, tar and/or silicon sealant for this,
depending on the existing roofing.

DOVRE
Subject to change because of technical improvements 13
Roof sleeve through a pitched roof
of flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Start at the stove and add the concentric pipes
one at a time, including the changes in direction
you want, along the route you decided on in
advance, up to just under the roof.
2. Decide on the location for the roof sleeve.
3. Make an elliptical hole so that a fire separation of
at least 50 mm remains round the pipe.
4. Extend the concentric pipe (1) until it extends at
least 250 mm above the roof surface (more is per-
mitted up to a maximum of 1000 mm stand-alone);
see next figure.
5. Center the pipe using the centering plates (2) and
attach it with the installation bracket (3).
6. Slide a roofing sheet for pitched roof (tar roof) or a
lead slab (4) (tile roof) over the pipe and seal or
cover it watertight.
7. Finish the seam between the pipe and the cone of
the roof sheet or lead slab watertight with silicon
sealant and if necessary a storm collar (5).
8. Install the roof sleeve (6) and secure it with the
clamping strap included in the delivery.
Establishing a gas connection
The connection to the gas pipe is on the back of the
gas regulator block, which is at the bottom right of the
stove.
The connection must meet the following conditions :
A coloured gas valve must be inserted in the gas
supply pipe, as close to the stove as possible and
always accessible.
The connection must be voltage-free.
Have a certified installer make the connection.
Follow the instructions below:
1. Check whether the type of gas and gas pressure
on site correspond with those marked on the type
plate.
The type plate is located on the appliance.
2. Assemble the gas supply pipe. 3/8” G pipe or cop-
per pipe with diameter 10/12 mm suffices for pipes
up to +/- 10 m. 1/2” G pipe or copper pipe with dia-
meter 13/15 mm is used for lengths exceeding 10
m.
3. Install the gas valve.
4. Connect the stove to the gas supply pipe. The gas
connection can be made using the opening on the
back. Use a 3/8” coupling to do this.
5. Check if the supply pipe is gastight (using soapy
water, for example).
Installing the remote control
set
The Mertik Maxitrol GV60 remote control set consists
of a handset (transmitter) and a receiver. The system
works on batteries; connecting an AC adaptor is
optional.
The batteries (2 x 1.5 Volt AAA for the handset
(transmitter), 4 x 1.5 Volt AA for the receiver)
are included.
Use only the Mertik Maxitrol AC adaptor or an
adaptor preapproved by Mertik Maxitrol. Other
adapters probably do not suit your system
and/or can damage it.
Batteries – handset (transmitter)
l2 x 1.5V AAA (LR 03) (recommended quality:
alkaline).
lHandsets with display: Battery indicator on the dis-
play.

DOVRE
14 Subject to change because of technical improvements
lWe recommend that you replace the batteries
every two years.
Batteries – receiver.
l4 x 1.5V AA (recommended quality: alkaline).
lIndicator light battery nearly empty: regular beeps
for three seconds when the motor is running.
lIn place of the batteries, it is possible to use an
AC adaptor.
Insert the batteries in the transmitter (handset) and
in the receiver (3) (black box, lid (6) can be opened
easily).
The receiver is situated in the base of the appli-
ance: this is easy to reach by removing the two
knurled screws (1) and letting the cover (2) drop
down; see the following figure.
76 5
12 43 5
09-20022-041
Programming the electronics code
Codes selected from approximately 65,000 randomly
available codes are automatically assigned to all Mer-
tik Maxitrol electronics. This code is assigned to the
handset for the remote control set. The receiver must
read this code from the handset.
The code only has to be set once, thus not
when you replace the batteries in the handset
or receiver.
1. Press the receiver’s reset button and continue
pressing until you hear two beeps; see next figure.
Release the reset button after the second beep.
The first beep is short and the second is long.
09-20020-216
2. Within 20 seconds press the button (small
flame) on the handset until you hear two additional
short beeps. The code is now set. If you hear a
long beep, this means that programming the code
was not successful, for example because the wir-
ing is incorrect. Check the wiring and try again.
Placing decorative wood
block set
The blocks are fragile, treat them with care.
The blocks must be placed on the burner
exactly as indicated in the photos.
Follow the instructions below to place the blocks:
When positioning the wood block set, make sure that
the pilot flame and the second thermocouple remain
free. Position the components in the way shown in the
following figures.
The wood block set consists of eight ceramic wood
blocks, coals and filament.
1. Position the coals and the filament.

DOVRE
Subject to change because of technical improvements 15
2. Position the wood blocks in the sequence dis-
played in the following figures:

DOVRE
16 Subject to change because of technical improvements
The way the coals are spread over the burning
surface partly determines the flame effect. In
certain cases it may be necessary to change
the distribution of the coals by partially uncov-
ering some burner openings, for example, in
order to obtain a better-distributed flame effect.
5. Replace all the disassembled parts in the correct
position in the appliance.
The appliance is now ready for use.
Use
First use
When you use the appliance for the first time, run it at
the highest setting for a few hours and ventilate the
room adequately at the same time. This will cure the
heat-resistant paint finish. Some white deposit may
appear on the glass and the inside. Once the
appliance has cooled down, you can easily remove
this deposit with a cloth. Clean the glass pane before
using the appliance, to prevent dirt from burning in.
Operating instructions
Remote control
09-20021-370
9
10
7
8
6
5
11 1 2 3 4
12 13 14 15
16 17 18 19
1. Time
2. Signal indicator
3. Thermostat mode
4. Battery indicator
5. Fahrenheit or Celsius
6. Eco mode
7. Double burner
8. Temperature
9. Programme mode
10. Timer
11. Child safety lock
12. On / off
13. Timer
14. Thermostat
15. Higher
16. Programme
17. Double burner
18. Eco
19. Lower

DOVRE
Subject to change because of technical improvements 17
Fahrenheit or Celsius
09-20021-371
To switch between °C and °F press [on/off] and
[timer] at the same time.
°F displays a 12-hour clock and
°C displays a 24-hour clock.
Setting the hour
09-20021-373
1. Press the and buttons at the same time. The
Day starts blinking.
2. Press the button or to select a number that
corresponds with the day of the week (1=
Monday, 2= Tuesday, 3= Wednesday, 4=
Thursday, 5= Friday, 6= Saturday, 7= Sunday).
3. Press the and buttons at the same time. The
Hour starts blinking.
4. Press or to select the hour.
5. Press the and buttons at the same time. The
Minutes start blinking.
6. Press or to select the minutes.
7. Press and at the same time to confirm or
wait.
Child safety lock
ON: To activate press the [on/off] and buttons at
the same time. The symbol for the child safety lock is
displayed and the handset, except for the OFF func-
tion, cannot be used.

DOVRE
18 Subject to change because of technical improvements
OFF: To deactivate, press the [on/off] and buttons
at the same time. The symbol for the child safety lock
disappears.
Switching on the stove
Before switching on the appliance, the Manual button
on the GV60 gas valve must be ON and the on/off
switch on the gas valve must be ON
Once the pilot flame is lighting, the motor will
automatically switch to the maximum flame
setting
One-button operation
09-20021-374
Press the [on/off] button (one-button ignition) until you
hear two short beeps and you see a blinking series of
lines
This confirms that the initiation sequence has started;
release the button.
lThe mains gas starts flowing as soon as the
pilot flame has been ignited.
lThe handset automatically switches to Manual
mode after the main burner has been ignited.
You can switch from one-button ignition to two-button
ignition by holding down the [on/off] button for longer
than 10 seconds after inserting the batteries. ON
appears on the display, 1 starts blinking. When the
switch has been made, 2 starts blinking
Two-button operation
09-20021-375
Press the [on/off] button and (two-button ignition)
until you hear two short beeps and you see a blinking
series of lines
This confirms that the initiation sequence has started;
release the button.
lThe mains gas starts flowing as soon as the
pilot flame has been ignited.
lThe handset automatically switches to Manual
mode after the main burner has been ignited.
You can switch from two-button ignition to one-button
ignition by holding down the [on/off] button for longer
than 10 seconds after inserting the batteries. ON
appears on the display, 2 starts blinking. When the
switch has been made, 1 starts blinking

DOVRE
Subject to change because of technical improvements 19
Switching off the appliance
09-20021-376
Press the [on/off] button to switch off the appliance.
There is a 5-second delay before the next ignition is
possible.
Setting the flame height
09-20021-377
Press to increase the flame height.
To reduce the flame height or to switch the appliance
to the pilot flame, hold down the button.

DOVRE
20 Subject to change because of technical improvements
High or low flame
09-20021-378
Double-click the button to switch to low flame. LO
appears on the display
09-20021-379
Double-click the button to switch to high flame. HI
appears on the display
Timer
09-20021-380
ON / SETTING:
1. Hold down the [Timer] button until the Timer sym-
bol is displayed and the hour starts blinking.
2. Press or to select the hour.
3. Press the [Timer] button to confirm. The minutes
start blinking
4. Press or to select the minutes.
5. Confirm by pressing the [Timer] button or wait.
OFF:
Press the [Timer] button and the symbol and the
countdown time disappear.
NOTE: At the end of the countdown time, the
flame is switched off. The Timer works only in
Manual, Thermostatic, and Eco mode. The
maximum countdown time is 9 hours and 50
minutes.