Draper 16056 Firmware update

INSTRUCTIONS FOR
32.5cc Petrol
2-in-1Garden Tool
Stock No.16056 Part No.GTP32
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
ATTENTION!:
2 stroke engines MUSTbe filled with
unleaded fuel, MIXED with 2-stroke oil.
Failure to add oil or incorrectly mixingthe oil
WILL result in running problems or
ENGINE FAILURE!

1. TITLE PAGE
1.1 INTRODUCTION
USER MANUAL FOR:
32.5cc PETROL 2-IN-1 GARDEN TOOL
Stock no. 16056
Part no. GTP32
1.2 REVISIONS
As our user manuals are continually updated, users should make sure that they use the very
latest version.
Downloads are available from: http://www.drapertools.com/manuals
DRAPER TOOLS LIMITED WEBSITE: www.drapertools.com
HURSLEY ROAD PRODUCT HELPLINE: [phone]
CHANDLER’S FORD GENERAL FAX: [phone]
EASTLEIGH
HAMPSHIRE
SO53 1YF
UK
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT
WARNING! Information that draws attention to the risk of injury or death.
CAUTION! Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal & educational use only.
Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other
form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
Date first published April 2016.

3
2. CONTENTS
2.1 CONTENTS
Page content Page
1. TITLE PAGE
1.1 INTRODUCTION .............................. 2
1.2 REVISION HISTORY.......................... 2
1.3 UNDERSTANDING THIS MANUAL .. 2
1.4 COPYRIGHT NOTICE........................ 2
2. CONTENTS
2.1 CONTENTS ....................................... 3
3. GUARANTEE
3.1 GUARANTEE .................................... 4
4. INTRODUCTION
4.1 SCOPE ............................................. 5
4.2 SPECIFICATION ................................ 5
4.3 HANDLING & STORAGE .................. 5
5. HEALTH & SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOL USE ................... 6
5.2 ADDITIONAL SAFETY INSTRUCTIONS
FOR 4-IN-1 PETROL
GARDEN USE ................................... 8
5.3 HEALTH AND SAFETY ......................
INFORMATION CONCERNING THE ..
USE OF FUELS ................................ 19
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION ............................ 10
– Hedge trimming attachment .... 11
– Grass trimmer ............................. 11
7. UNPACKING & CHECKING
7.1 PACKAGING................................... 12
7.2 WHAT’S IN THE BOX ..................... 12
8. PREPARING THE 2-STROKE MOTOR UNIT
8.1 FUELLING ....................................... 13
9. PREPARING THE ATTACHMENTS
9.1 FITTING THE GRASS TRIMMER ........
GUARD........................................... 14
9.2 FITTING THE COMPLETE SPOOL ......
ASSEMBLY ..................................... 14
9.3 CONNECTING THE ATTACHMENTS ..
....................................................... 14
10. STARTING THE 2-STROKE MOTOR UNIT
10.1 STARTING THE ENGINE ................. 15
11. OPERATING THE HEDGE TRIMMING
ATTACHMENT
11.1 ADJUSTING THE BLADE ANGLE.... 16
11.2 WORKING TECHNIQUES ............... 16
– Ground clearance....................... 16
– Vertical cutting (along side) ...... 17
– Vertical cutting (at a distance) .. 17
– Hedge topping
(above head height) .................. 17
– Horizontal cutting...................... 17
12. OPERATING THE GRASS TRIMMER
12.1 USING THE GRASS TRIMMER........ 18
13. MAINTENANCE – 2-STROKE MOTOR UNIT
13.1 CLEANING THE AIR FILTER............ 19
13.2 SPARK PLUG MAINTENANCE........ 19
13.3 ENGINE SPEED IDLE ..........................
ADJUSTMENT ................................ 20
13.4 REPLACING THE FUEL FILTER........ 20
14. MAINTENANCE – ATTACHMENTS
14.1 GEARBOX LUBRICATION .............. 21
14.2 BLADE CLEANING.......................... 21
14.3 MAINTAINING THE SPOOL ........... 21
14.4 ATTACHING THE COMPLETE
SPOOL ASSEMBLY ......................... 21
14.5 REWINDING THE SPOOL INSERT... 22
15. TROUBLESHOOTING
15.1 TROUBLESHOOTING –2-STROKE ......
MOTOR UNIT................................. 23
15.2 TROUBLESHOOTING – HEDGE .........
TRIMMING ATTACHMENT ............ 25
16. ACCESSORIES
16.1 ACCESSORIES GUIDE ..................... 26
17. DISPOSAL
17.1 DISPOSAL....................................... 27
18. EXPLANATION OF SYMBOLS
18.1 EXPLANATION OF SYMBOLS ........ 28
DECLARATION OF CONFORMITY .............Enclosed
2. CONTENTS
Page content Page

4
3. GUARANTEE
3.1 GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are guaranteed
to be free from defective materials and workmanship for a period of 12 months from the
date of purchase except where tools are hired out when the guarantee period is 90 days
from the date of purchase.
A proof of purchase must be provided with the tool.
Should the machine develop any fault, please return the complete tool to your nearest
authorized warranty repair agent or contact Draper Tools Limited, Chandler's Ford, Eastleigh,
Hampshire, SO53 1YF. England. Telephone Sales Desk: [phone] or Product Helpline
[phone].
If upon inspection it is found that the fault occurring is due to defective materials or
workmanship, repairs will be carried out free of charge. This guarantee does not apply to
normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe
handling, alterations, accident, or repairs attempted or made by any personnel other than
the authorised Draper warranty repair agent.
NOTE: If the tool is found not to be within the terms of warranty, repairs and carriage
charges will be quoted and made accordingly.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of
its terms are not authorised.
Your Draper guarantee is not effective unless you can produce upon request a dated receipt
or invoice to verify your proof of purchase within the 12 month period.
Please note that this guarantee is an additional benefit and does not affect your statutory
rights.
Draper Tools Limited

5
4.3 HANDLING & STORAGE
Care must be taken when handling and lifting. This machine is not a toy and must be
respected.
The environment will have a negative result on its operation if you are not careful. If the air
is damp, components will rust. If the machine is unprotected from dust and debris;
components will become clogged: And if not cleaned and maintained correctly or regularly
the machine will not perform at its best.
ALWAYS WEAR SUITABLE AND APPROVED PERSONAL PROTECTIVE EQUIPMENT
4. INTRODUCTION
4.1 SCOPE
This domestic, portable hand-held 2 stroke 2-in-1 garden tool is designed exclusively for
connection to either a grass trimmer or a hedge trimmer.
4.2 SPECIFICATION
Stock no .............................................................................................................................16056
Part no .............................................................................................................................. GTP32
Motor unit:
Maximum engine performance....................................................................................... 1,0kW
Engine type.................................................................................................................... 2-stroke
Fuel tank capacity ......................................................................................................... 900cm³
Engine displacement .................................................................................................... 32.5cm³
Fuel/2-stroke oil mix ............................................................................................................25:1
Maximum engine performance................................................................................... 1.000kW
Engine speed at idle.....................................................................................................3000rpm
Engine speed (rotational frequency)2 .................................................................... 7,500min-1
Engine speed (rotational frequency)3 .................................................................... 3,000min-1
Fuel consumption at maximum engine performance..............................................503g/kWh
Sound pressure level (A-weighted LpAav)1.............................................................. 93.7dB(A)
Sound power level (A-weighted LWAav)1.............................................................. 110.5dB(A)
Single value noise level2............................................................................................. 114dB(A)
Vibration level3..............................................................................................................7.29m/s²
Weight (motor & grass trimmer attachment only - no fuel) ............................................. 6kg
Grass trimmer attachment:
Cutting diameter (nylon line)........................................................................................ 440mm
Cord diameter ................................................................................................................. 2.5mm
Overall cord length ............................................................................................................
2.5M
Cord extension .............................................................................................................Tap’n go
Noise level............................................................................................94.5dB(A) [K=3,0 dB(A)]
Vibration – full throttle ...........................................................................9.23m/s² [K=1,5 m/s²]
Vibration – idling speed.............................................................................3.2m/s² [K=1,5 m/s²]
Hedge trimmer attachment
Max. branch size............................................................................................................... 22mm
Blade length ................................................................................................................... 440mm
Cutting length................................................................................................................ 380mm
Noise level............................................................................................94.5dB(A) [K=3,0 dB(A)]
Vibration – full throttle ...........................................................................9.23m/s² [K=1,5 m/s²]
Vibration – idling speed.............................................................................3.2m/s² [K=1,5 m/s²]
1 In accordance to BS EN ISO 22868.
2 A-weighted sound pressure level in accordance to 2000/14/EC.
3 In accordance to BS EN ISO 22867.

6
5. HEALTH & SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
When using any type of power tool there are steps that should be taken to make sure that
you, as the user, remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
Read the instruction manual fully. Do not attempt any operation until you have read and
understood this manual.
Most important you must know how to safely start and stop this machine, especially in an
emergency.
Keep the work area tidy and clean. Attempting to clear clutter from around the machine
during use will reduce your concentration. Mess on the floor creates a trip hazard. Any
liquid spilt on the floor could result in you slipping.
Find a suitable location. The location should provide good natural light or artificial lighting
as a replacement. Avoid damp and dust locations as it will have a negative effect on the its
performance. If the machine is portable; do not expose to rain. In all cases do not operate
power tools near flammable materials.
Beware of electric shock. Avoid contact with earthed surfaces; because they can conduct
electricity if there is an electrical fault with the power tool.
Keep bystanders away. Children, onlookers and passers-by must be restricted from entering
the work area for their own protection. The barrier must extend a suitable distance from the
tool user.
Do not overload or misuse the tool. All tools are designed for a purpose and are limited to
what they are capable of doing. Do not attempt to use a power tool (or modify) for an
application it is not designed for. Select a tool appropriate for the size of the job.
Overloading a tool will result in tool failure and user injury: This includes the use of
accessories.
Dress appropriately. Clothing should be close fitted, with any long hair tired back and
jewellery and neck ties removed as they can cause an entanglement risk, resulting in body
parts being pulled into the machine. Footwear must be fully enclosed and have a nonslip
sole.
Wear personal protective equipment (PPE). Dust, noise and vibration can all be dangerous if
not suitably protected against. If the work involving the power tool creates dust or fumes;
wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods
must be protected against. Wear vibration reducing gloves and allow long breaks between
uses. Protect against dust by wearing approved safety goggles or a face shield. In addition
to these common hazards, find out what others may be associated with the machine/work
process and wear the most suitable protective equipment available.
Do not breathe contaminated air. If the work creates dust or fumes; connect the machine (if
possible) to an extraction system either locally or remotely. Working outdoors can also help
if possible.

7
5. HEALTH & SAFETY INFORMATION
Move the machine as instructed. If the product is heavy; employ a second or third person to
help move it safely or use a mechanical device. Always refer to the instructions for the
correct method.
Do not overreach. Extending your body too far can result in a loss of balance and you
falling. This could be from a height or onto a machine and will result in injury.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any
damaged or missing parts immediately with original parts from the manufacturer. As
applicable; keep blades sharp; moving parts clean, oiled or greased; handles clean; and
emergency devices working.
Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts
may continue to move due to momentum. Wait for all parts to stop; then unplug it from the
power supply before making any adjustments, carrying out maintenance operations or just
finishing using the tool.
Remove and check setting tools. Some machinery requires the use of additional tools or keys
to set, load or adjust the power tool. Before starting the power tool always check to make
certain they have been removed and are safely away from the machine.
Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a
power tool if you are under the influence of drugs (prescription or otherwise), including
alcohol or if you are feeling tired. Being disorientated will result in an accident.
Have this tool repaired by a qualified person. This tool is designed to confirm to the
relevant international and local standards and as such should be maintained and repaired by
someone qualified; using only original parts supplied by the manufacturer: This will ensure
the tool remains safe to use.

8
5. HEALTH & SAFETY INFORMATION
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR 2-IN-1 PETROL
GARDEN TOOL USE
WARNING! For your safety, please read and understand these instructions before assembling,
operating or maintaining this machine.
WARNING! Read the instructions carefully.
Never attempt to modify or operate a modified machine. Fully assemble this machine,
including all relevant guards, before operating.
Do not operate this machine without being completely familiar with the safety features and
how to operate them.
Never operate this machine if the stop switch is faulty or not functioning.
Never operate this machine while tired, ill or under the influence of drugs.
DANGER! Keep out of the reach of children.
Refer to the instructions supplied with the attachment. Fully read and understand before
attempting to assemble, operate or maintain the attachment.
Never allow people unfamiliar with these instructions to operate this machine. Local
regulations may restrict the age of the operator.
Prior to each use, inspect the machine for signs of damage. Make sure the safety features are
present and functioning and that all visible nuts, bolts and screws remain tight. Vibration
from normal use can cause them to loosen over time.
Never operate this machine with defective or missing guards.
WARNING! Use of this product can pose a danger to wildlife. Before
attempting to use this machine, check the area, particularly long grass and
under bushes for signs of life: if necessary relocate.
NOTE: Not all animals will be deterred by the noise of the product alone.
Do not operate this machine near animals or bystanders.
Check the attachment is correctly fitted to the machine before attempting to start the
engine.
CAUTION! As the user you are responsible for any injury to people or damage to property.
Never leave this machine running when not in use or leave the it unattended during use.
WARNING! During use the engine gets very hot. Do not touch it, especially the exhaust.
Always be aware of your surroundings, staying alert for possible hazards that you may not
hear over the noise of the engine.
Always wear appropriate PPE [Personal Protective Equipment].
– Always wear suitable eye/face protection.
– Ear defenders must be worn to prevent damage to your hearing.
– Gloves to help reduce vibration fatigue.
– Always wear safety footwear.

9
5. HEALTH & SAFETY INFORMATION
5.3 HEALTH AND SAFETY INFORMATION CONCERNING THE USE OF FUELS
Fuels are inflammable and explosive. Reduce the risk of explosion and fire by:
– Turning off and cooling the motor down before filling the tank with fuel.
– Refraining from smoking and starting open fires when handling fuels.
– Storing and mixing fuels in approved and correspondingly labelled canisters.
– Storing fuels in closed containers. Keeping in mind that fuels may evaporate at room
temperature and collect on the floor of closed rooms (risk of explosion).
– Start the device at least nine metres away from the machine.
Fuels are toxic, they contain substances that have an immediate toxic effect and may cause
permanent damage to your health. Take all precautionary measures to prevent your body
from absorbing any of these substances:
– Tank and siphon fuels only outdoors or in well-ventilated rooms.
– Do not inhale fuel fumes.
– Avoid contact with eyes and skin.
– Wear gloves when transferring fuel.
– When fuel has come into contact with your clothes, change them immediately. Clean your
clothes before putting them back on.
– Store fuels out of the reach of children.
When handled inappropriately, fuels may cause damage to the environment:
– Transfer fuel carefully. Fuel must never trickle into the ground or the sewage system.
– Dispose of any remaining fuel in an appropriate manner. Never dispose of fuel with
regular household waste.
– Fuels may be stored only for a limited time. Purchase only such quantities that can be used
up within a few months.

10
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION
2-Stoke motor unit:
 Air filter housing.
 Fuel primer.
 Carburettor.
 Choke lever.
 Fuel tank.
 Spark plug cover (H.T lead).
 Pull start assembly.
 Exhaust.
 Throttle lever.
 Throttle release lever.
 Throttle lock (start position).
 Engine stop switch.
 Front (auxiliary) handle.
 Power take off.
 Power take off locking handle.
 Power take off release latch.


 



 








11
6. TECHNICAL DESCRIPTION
 Power take off connection point.
 Shaft.
 Cutting filament trimming blade.
 Cutting attachment guard.
 Spool assembly.
 Spool housing.
 Spool insert.
 Nylon cutting line.
 Spool cover.
 Angle adjustment locking lever.
 Angle adjustment lever.
 Adjustment handle.
 Gearbox.
 Grease nipple.
 Blade.
 Blade guards.
Hedge trimmer attachment:
Trimmer attachment:



















12
7. UNPACKING & CHECKING
7.1 PACKAGING
Carefully remove the products from the packaging and examine them for any sign of damage
that may have happened during shipping. Lay the contents out and check them against the
parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the
telephone number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the guarantee period: in case the
machine needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave
any of these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly;
according to local regulations.
7.2 WHAT´S IN THE BOX?
As well as the 2-in-1 garden tool, there are several parts not fitted or attached to it.
Front (auxiliary) handle.
Grass trimmer shaft.
 Cutting attachment guard and fittings.
 Cutting filament line spool.
 2-stroke mixing bottle.
 Spark plug spanner.
 2 × hex keys.
 Combination spanner.





 

13
8. PREPARING THE 2-STROKE MOTOR UNIT
8.1 FUELLING – FIG. 1
This Draper petrol product is powered by a engine
which MUST be filled with unleaded fuel MIXED
with 2-stroke oil. Failure to add oil or incorrectly
mixing the oil and fuel can result in running
problems or engine failure. Any machine returned
under warranty which is found to have failed due to
a lack of lubrication will be considered a chargeable
repair.
Only use fresh, clean, and good quality unleaded
fuel mixed with synthetic 2-stroke oil in a ratio of
25:1.
Before attempting to fuel this machine, make sure
you have completely read and understood the safety instructions.
Danger! Fuel is highly flammable.
– Open the fuel cap by turning it anticlockwise. Hang it to one side so that it does not
block the opening.
– Combine fuel and 2-stroke oil to create a 25:1 mixture.
Example: Add 40ml of synthetic 2-stroke oil in to 1,000ml (1 litre) unleaded fuel and shake
well to produce a 25:1 mix.
Fuel quality degrades rapidly: Avoid storing fuel by mixing only what you require.
Using fuel that has degraded will cause starting/running problems.
– Carefully pour the mixture into the fuel tank filling it while taking care not to spill or
waste any. Have a rag to hand to clean away any residue or spilt fuel.
– Replace the fuel cap making sure it is seated properly before tightening clockwise. If
the threads become crossed it will damage the tank. It may also result in fuel leaking out
during use and potentially causing a fire risk.
FIG. 1  

14
9. PREPARING THE ATTACHMENTS
9.1 FITTING THE GRASS TRIMMER GUARD
(FIG.2)
The guard must be fitted and fully operational
before using this machine.
– Offer up the guard to the shaft, attached
bracket to back with hex bolts finger tight.
– Use hex. keys to tighten bolts when guard is
lined up as shown.
FIG.2
9.2 FITTING THE COMPLETE SPOOL
ASSEMBLY (FIG.3)
– With the engine stopped, locate the spindle locking
access point .
– Using a 10mm spanner locate it onto the flat sides
of shaft.
Screw the spool  onto the shaft clockwise by
hand.
9.3 CONNECTING THE ATTACHMENTS (FIG.4)
– Before attempting to start the engine, this
attachment must be correctly assembled to the
engine output shaft's, power take off.
– Make sure the locking handle  is loose by
turning it anticlockwise a few turns.
– The shield which is sprung loaded will pop up.
– Slide the attachment shaft inside the power
take off collar of the engine unit.
– As the holes line up the sprung loaded lock
mechanism  will click and locate into hole to
lock attachment in position.
– Push cover back over and tighten the locking
handle  clockwise.
Disconnection
– To disconnect loosen locking handle, shield will pop
up.
– Then push thumb down on into recess onto sprung
loaded locking latch  and pull the attachment
out.



 

FIG.3
FIG.4

15
10. STARTING THE 2-STROKE MOTOR UNIT
Do not attempt to start this machine until you have
read and understood all the safety instructions.
10.1 STARTING THE ENGINE (FIGS.5 – 7)
Warning! In an emergency, slide the engine stop
switch  forward to kill the engine.
– Slide the engine stop switch backward.
– Grip the front handle and squeeze and hold the
throttle lock button  whilst at the same time
depressing the throttle safety lever  and
throttle . When slowly released, the throttle
 should be held in its start position by throttle
lock button .
Cold starts – close the choke to restrict the amount
of air entering the engine. Slide the choke lever

to the OFF position.
Warm starts – open the choke to increase the
amount of air entering the engine. Slide the choke
lever
 to the ON position.
– Prime the engine with fuel. Press the fuel primer
 3 or 4 times. The primerand fuel line from the
tank should have fuel present.
Attention! Over priming will cause the engine to
flood with too much fuel. This will engulf the spark
plug and stop the engine from starting. There will
be a stronger smell of fuel when this occurs.
– Grip the neck of the motor unit with your left
hand holding the machine firmly on the ground.
Crouch over the machine while maintaining firm
footing.
Attention! Do not stand or apply any pressure on
to the output shaft.
– With your right hand hold the pull start handle .
– Make 2 or 3 short, sharp pulls of the starter or
until the engine starts. If the engine does not
start by the fifth crank, move the choke setting.
Warning! Do not pull the starter rope out fully as it
may break. Do not release the starter rope and allow it to recoil unaided.
– When the engine starts, squeeze throttle lever
 to release the 'start' position.
– When the engine has been running for a few minutes open the choke fully.
Attention! The majority of engines have an initial period in which the internal components
bed themselves in. This engine is no different. During this the first 5 or 6 tank fulls [bedding
in period], running the engine in the very high rev. range must be avoided as the stresses
involved can cause damage to the engine.
FIG.5
FIG.6

FIG.7






16
11.1 ADJUSTING THE BLADE ANGLE
(FIG.26)
Depending upon the circumstances, the cutting
head can be adjusted to suit access to the hedge.
– With the engine stopped, grip the adjustment
handle .
– Lift the angle adjustment locking lever  and
hold.
– With your thumb, press down the angle
adjustment lever  and adjust the cutting
head to a suitable angle.
– Release lever  and make sure the cutting
head has locked into position fully.
11.2 WORKING TECHNIQUES (FIGS.9 – 13)
Some local authorities impose seasonal bans on hedge cutting. Check with your local
authority to make sure this does not affect you.
Beware of hidden objects. Check there are no wire fences, power cables or other objects
hidden within the hedge that will damage this machine or cause injury if cut by the blades
Remove the blade guard before starting the engine.
The metal blade is intended for cutting branches up to 22mm and can be used to clear scrub
or off shoots around the base of shrubs, brushes and hedges.
The metal blade is a consumable item, avoiding
contact with larger branches, roots, stones, walls,
fences and other hard surfaces will help prolong the
life of it.
Before using the hedge trimmer, remove any large
branches with a pair of loppers.
GROUND CLEARANCE
Before all the hedge trimmings fall and obscure the
base of the hedge, clear out any unwanted new
shoots or woody weeds.
– Adjust the cutting head.
– Manoeuvre the cutting head in and around the
root, avoiding large diameter limbs, roots and
stones.
WARNING! Use of this product can pose a
danger to wildlife. Before attempting to
use this machine, check the area,
particularly long grass and under bushes for signs
of life: if necessary relocate. NOTE: Not all animals
will be deterred by the noise of the product alone.
11. OPERATING THE HEDGE TRIMMING ATTACHMENT

FIG.8
FIG.9

 

17
11. OPERATING THE HEDGE TRIMMING ATTACHMENT
VERTICAL CUTTING [ALONG SIDE] (FIG.10)
The best practice is to cut the front and side of a
hedge first before finishing with the top
– Set the cutting head straight.
– Make large sweeping arcs with the cutting head,
using both sides of the blade to trim material
from the hedge.
Stand back at regular intervals. What 'looks' to be a
straight and level cut from close up will look quite
different from a distance.
VERTICAL CUTTING [AT A DISTANCE] (FIG.11)
If an obstacle prevents you from standing directly
next to the hedge [for example a flower bed] follow
the steps as per vertical cutting but with the cutting
head at a more suitable angle.
HEDGE TOPPING [ABOVE HEAD HEIGHT] (FIG.12)
Although it is possible to cut the top of a tall hedge
in this method, using a safe platform to raise
yourself level with the hedge top is preferred and
will result in a more attractive finish.
– Set the cutting head at 90 degrees.
– Twist the shaft to make the cutting head swing in
an arc across the top of the hedge.
– Working in this position is particularly difficult.
Take regular breaks to avoid strain or injury.
HORIZONTAL CUTTING (FIG.13)
The final stage is to shape the top of the hedge.
– Set the cutting head straight.
– Make level arcs, so as to encourage the trimmings
on to the floor.
Do not attempt to cut a hedge higher than chest
height without using a safe platform.
Warning! If working on a platform, do not attempt
to stretch or over reach.
When cutting with the blade set straight, tilt the
cutting side of the blades toward the hedge by
approximately 0-10 degrees.

FIG.10
FIG.11
FIG.12
FIG.13

18
✔
12. OPERATING THE GRASS TRIMMER
12.1 USING THE GRASS TRIMMER (FIG.14)
Warning! Use of this product can pose a
danger to wildlife. Before attempting to
use this machine, check the area,
particularly long grass and under bushes for signs of
life: if necessary, relocate.
Note: Not all animals will be deterred by the noise
of the product alone. The nylon line is intended for
clearing grass, weeds and similar soft vegetation.
The nylon line is a consumable item, avoiding
contact with trees, stones, walls, fences and other
hard surfaces will help prolong the life of it.
– Begin cutting at full throttle, hovering the spool
assembly just off the ground while making arc
shaped sweeping actions through the vegetation.
The nylon line must be keep level with the
ground to avoid scalping the ground surface.
When the nylon line is running at speed take care
to avoid plastic items such as garden furniture,
flower pots and other equally fragile materials to
avoid damage.
While cutting vegetation it is possible to tell when
the line length is deteriorating; the cutting distance
from the spool head will decrease. Before the line
disappears inside the spool housing strike the
cutting head  [while it is running at speed] on
to a piece of suitable ground. This will release a set
amount of line from the head which will be drawn
out by the rotating [centrifugal] force. Any excess
line is automatically trimmed as it strikes the
trimming blade on the underneath of the guard .
If the line is left or a breakage causes it to disappear
inside the spool housing the sound made by the
spool head spinning changes.
FIG.14



19


13. MAINTENANCE – 2-STROKE MOTOR UNIT
Regular maintenance tasks must be carried out at
specific intervals to retain the engine's performance.
13.1 CLEANING THE AIR FILTER (FIG.15)
A dirty, clogged air filter will restrict the air flow in
to the engine and will cause rough running. It will
increase fuel consumption and may result in starting
problems.
Attention Stop the engine before removing the air
filter assembly.
– Set the choke lever to the closed position to
prevent any debris entering the carburettor inlet.
– Turn screw  anticlockwise to remove it.
– Lift cover  away at the bottom, then lift it free from the tab at the top.
– Remove and wash the foam air filter element  in warm soapy water to clean it. Do not
use solvents to clean it.
– Allow the filter to dry 100% before refitting it on to the engine.
– Refit cover .
– Insert screw  and turn clockwise to tighten. Replace the filter if it appears worn or
damaged.
13.2 SPARK PLUG MAINTENANCE (FIGS.16 – 17)
Over time the spark plug can become contaminated.
This can be due to adverse running conditions such
as, working with part throttle for a prolonged
period or a fuel mix containing too much oil. This
contamination can build up causing the engine to
run roughly, reduce the fuel consumption or create
starting problems.
– Without using any tools [so as to avoid damaging
the H.T. lead] remove the lead  from the back
of the spark plug.
– Using the spark plug spanner supplied , turn
the spark plug  anticlockwise to remove it.
– Clean the spark plug and check the electrode gap.
Maintain a gap of 0.6 to 0.7mm.
Attention The spark plug should be replaced every
60 hours of machine use or annually during a
service. The replacement plug must be an NHSP
L8RTF, Oregon O-P17Y or another compatible
resistor type plug with the same heat range.
– Make sure you correctly seat the spark plug
thread in to the engine before screwing it
clockwise in to the head.
FIG. 34

FIG.15
FIG.16





20
13. MAINTENANCE – 2-STROKE MOTOR UNIT
– Tighten the spark plug  using the spark plug
spanner , before replacing the H.T. lead .
The rubber surround of the H.T. lead cap should
be tucked inside the plastic housing of the body
to make sure of a good connection with the spark
plug.
13.3 ENGINE IDLE SPEED ADJUSTMENT
(FIG.18)
With the engine running at idle the attachment
must not operate. For example, the brush cutter
blade must not spin while the engine idles. Adjust
as necessary.
– Run the engine until it is warm.
– Turn screw
 anticlockwise to decrease the
engine idle speed.
13.4 REPLACING THE FUEL FILTER (FIG.19)
To make sure the supply of fuel remains clean there
is a small fuel filter attached to the pick-up tube
inside the fuel tank. This must be checked regularly
and replaced when clogged.
– Drain fuel tank completely.
– Gently pull the fuel tank cap and chain to release
the spring clip
 from inside the tank mouth.
– Tilt the engine so that the fuel tank opening is
the lowest point and shake. This will cause the
fuel filter
 to fall in to reach.
– Gently pull the filter clear of the tank mouth.
– Without letting go of the pick-up line
 , squeeze the hose clip  and move it away
from the filter.
– While still holding the fuel line, pull the clogged filter off and insert the clean filter.
– Reposition the hose clip
 to grip the fuel line on to the filter.
– Push the filter back inside the tank.
– Squeeze the spring clip
 and push it back inside the mouth of the fuel tank.
FIG.17

FIG.18
FIG.19


 
