Dream On Me 630 User manual

1
STYLE NO: 630
Read all instructions BEFORE assembly and USE of product.
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help
you quickly assemble your products.Before you begin we
recommend that you following the steps below:
1.Please read the instructions thoroughly.
2. Identify all parts and hardwares
3.You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a
soft surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the
surface and could damage the protective coating.
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.
KEEP INSTRUCTIONS FOR FUTURE USE.
Infants can suffocate
In gaps between a mattress too small or too thick and product sides.
On soft bedding NEVER add a mattress,pillow,comforter,or padding.
The Product,including side rails,must be fully erected prior to use.
Always provide the supervision necessary for the continued safety
of your child.When used for playing,never leave child unattended.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788

2

3
WARNING !
MADE IN CHINA
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
·
· CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING
PARTS OR SHARP EDGES BEFORE AND AFTER ASSEMBLY.A FREQUENT CHECK
DAMAGED OR BROKEN.CONTACT DREAM ON ME INC.1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATURE IF NEEDED.DO NOT SUBSTITUTE PARTS.
· TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS
BE PLACED ON THEIR BACKS TO SLEEP, OTHERWISE ADVISED BY YOUR
PHYSICIAN.
· STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING
AROUND A CHILD’S
NECK,SUCH AS HOOD STRINGS OR PACIFIER CORDS.
DO NOT SUSPEND STRINGS OVER A CRIB OR ATTACH A
STRINGS TO TOYS.
· TO HELP PREVENT STRANGULATION TIGHTEN ALL FASTENERS. A CHILD CAN
TRAP PARTS OF THE BODY OR CLOTHING ON LOOSE FASTENERS.
· DO NOT PLACE CRIB NEAR WINDOWS WHERE CORDS FROM BLINDS OR DRAPS
MAY STRANGLE A CHILD.
· WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO THE
LOWEST POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER
OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT.
· WHEN CHILD IS ABLE TO CLIMB OUT OR REACH THE HEIGHT OF 35 IN.(89CM),
THE CRIB SHALL NO LONGER BE USED.
· DO NOT USE A WATER MATTRESS WITH THIS CRIB.
· REPLACE TEETHING RAIL IF DAMAGED, CRACKED OR LOOSE.
· IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S
PRODUCTS.
· NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS
COVERS BECAUSE THEY CAN CAUSE SUFFOCATION.
· INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS
THAT IS TOO SMALL.
· INFANTS CAN SUFFOCATE ON SOFT BEDDING,NEVER ADD A PILLOW OR
COMFORTER.NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.
· FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB. SEE HEAD PANNEL AND
MATTRESS SUPPORT FOR WARNINGS AND INSTRUCTIONS.
SHOULD BE MADE DURING USE.DO NOT USE CRIB IF ANY PARTS ARE MISSING,
USE ONLY MATTRESS/PAD PROVIDED BY DREAM ON ME WHICH MUST BE AT
LEAST 37-3/4 IN.LONG BY 23-3/4 WIDE AND NOT MORE THAN 2 IN.THICK.
READ ALL INSTRUCTIONS BEFORE USE OF THE CHANGING TABLE,ADD-ON
CHANGING UNIT,OR CONTOURED CHANGING PAD.FOR THIS CHANGING TABLE,
THE MAXIMUM WEIGHT OF THE CHILD IS 30LBS.
DO NOT USE CHANGING TABLE,ADD-ON CHANGING UNIT,OR CONTOURED
CHANGING PAD IF IT IS DAMAGED OR BROKEN.

4
532 S WASHINGTON AVE PISCATAWAY TWP NJ 08854

5
CONNECTION HARD WARE
a: 1-1/5” Allen head
bolt (14 pcs)
b:Wood dowels (12pcs) c:Allen wrench (1pc) d:3” Allen head bolt (4pcs)
e:Barrel nuts (14 pcs) f: 3/4” Allen head bolt (4 pcs) h:1-1/5” Screw (3 pcs)
i:Knob (3pcs) j:Shelf support (4pcs)
PARTS ENCLOSED IN CARTON
A:Changer right side (1pc)
k:Washer (2pcs) l:Bolt (2pcs) m:Belt (1pc)
n:Tip over restraints (1pc)
B:Top rail (1pc)
C:Bottom bar (1pc)
Changer back Changer middle
E:Bottom bar (1pc)
D: Top bar (1pc)
B
C
D
E
g: 2-1/5”Allen head
bolt (10 pcs)
q:Bolt (1pc)
p:Cross screws (24pcs)
s. 1” Allen head Bolt (4pcs) t. Nuts (4pcs) WRENCH AND
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
r. Metal connetion (4pcs)
p

6
R:Wooden mattress base(1pc)
Z1:Smalll pad (1pc)
H
G
F
Changer front bar
F: Top (1pc)
G: Middle (1pc)
H:Bottom (1pc)
I:Changing surface (1pc)
J:Changer middle panel
K:Changer bottom shelf (1pc)
L:Changer left side (1pc) M:Left back leg (1pc)
N:Left board (1pc)
O:Left front leg (1pc)
Drawer T:Front panel (3pcs)
U:Left side panel (3pcs)
V: Right side panel (3pcs)
W:Back panel (3pcs)
X:Bottom panel (3pcs)
Q:Back rail bottom (1pc) S:Front rail bottom (1pc)
Y:Changer middle shelf (1pc)
Z2:Big pad (1pc)
T
U
V
WX
P:Back top rail(1pcs)

7
CRIB ASSEMBLY
Lay down the assembled parts on the floor .
Slide The changing surface (I) into the groove
in (D) along the groove between (B) and (G) .
Slide (J) into the groove in (A) along the groove
between (D) and (E) .
Then slide (K) into groove in (A) along the
groove between(C) and (E) .
STEP 2
Model shown is example only.
Styles may vary .
I
J
K
B
C
E
A
STEP 1
Attach The changer back(B&C) ,
and The changer middle(D&E) ,
and The changer front (F,G,&H)
toThe changer right side (A) using wood
dowels (b),
nuts(e) by allen
bolts (a),bolts (g) and barrel
wrench (c) .
Model shown is example only.
Styles may vary .
g
e
a
A
B
C
D
H
F

8
Attach left back leg (M) and
left front leg (O) to left board
(N) using bolts (d) and barrel
nuts (e) .
STEP 4
Model shown is example only.
Styles may vary .
d
d
e
e
e
e
STEP 3
Model shown is example only.
Styles may vary .
Attach The changer back (B&C) and
The changer middle (D&E) and The
changer front (F,G&H) to The
changer left side (L) using wood dowels
(b),bolts (a) and bolts (q) by allen
wrench (c) .
b
b
qq
b
c
B
I
H
F
LJ

9
STEP 6
Model shown is example only.
Styles may vary .
M
L
R
STEP 5
Model shown is example only.
Styles may vary .
Attach The top rail (P) and the
bottom rail (Q) to The changer
side (L) and left headboard
using wood dowels(b),bolts(q&g)
and barrel nuts(e) by allen wrench.
M
e
e
b
b
g
g
g
g
e
g
q q
e
e
s
t
Attach metal connection(r) to the
wooden mattress
base(R) by using bolts(s) and nuts(t) with wrench.
Position the wooden mattress base (R) to a
Insert the bolts(f) into thread inserts on legs,
then tighten securely with Allen wrench(d).
Be sure the flat side of wooden mattress
base(R) is upward.
WRENCH- NOT INCLUDE
selected position on legs.
$

10
STEP 7
Model shown is example only.
Styles may vary .
Attach The bottom front rail (S) to The
changer side (L) and the left head board
using bolts (g),barrel nuts (e) and allen
wrench (c) .Put the mattress(Z2) into
the bed.
g
e
e
S
g
g
g
STEP 8
Model shown is example only.
Styles may vary .
V
Attach left side panel (U) & right side
panel (V) to back panel (W) by
inserting cross screw (p) into the holes
on left side panel (U) & right side panel
(V) .
p
p
p
p
DO NOT tighten all .
Z2

11
STEP 9
Model shown is example only.
Styles may vary .
Slide the bottom panel (X) painted side
up , into grooves of the left side panel
(U) and the right side panel (V) . In
the end , insert the bottom (X) into the
groove of back panel (W) .
Attach the f
ront panel (T) to the left side panel (U) and the right side panel (V)
by inserting cross screws (p) into the holes on left side panel (U) &
right side panel (V) . Inserting the bottom panel (X) into the groove
of the front panel (T) . Tighten all the screws . Assemble the rest two
drawers follow step 8,9,10 .
STEP 10
Model shown is example only.
Styles may vary .
Attach the knob (i) to the front panel (T) by screw (h) .
p
p
p
p
i
h
T
T
XU
V

12
STEP 11
Model shown is example only.
Styles may vary .
Insert the shelf supports (j) in the holes in the posts of changing table.
Then place the changer middle shelf (Y) inside the shelf support.
Tighten the screws in the shelf supports (j) .
j
j
j
j
Y
PHILLIPS-- HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY- NOT INCLUDE

13
Model shown is example only.
Styles may vary .
STEP 12
1.Slide the drawers into rails on head board (A&L) .
2.Assembly the belt (m) to the changer side (A&L) using washer(k) and bolt(l).
3.Add the pad (Z1) .
4.Put the child on the pad,then insert safty restraint system of the tape across child's waist.
The tightness can be adjusted by increasing the te
5.Put the big pad (Z2) into the crib.
nsion of the tape.
lk
m
NOTE :PLEASE PUT THE
DRAWER WITH CLEAN
STICKER AS THE FIRST ONE.
A
L
T
T
T
Z1
Z2
PHILLIPS-- HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY- NOT INCLUDE

Converting crib to a day bed
14
Model shown is example only.
Styles may vary .
Model shown is example only.
Styles may vary .
You have the option to convert crib to a day bed
1:Remove the front rail bottom(S)
2:Install the Wooden mattress base (R)
in its lowest position.
Converting crib to a twin bed I
Conversion kit is sold separately You have the
option to convert crib to a twin bed
1:Use the front rail as the
footboard of twin bed I;
2:Use the back rail as the
headboard of twin
3:Connect the front rail and the
back rail to the
kits ( legs, long rails,and hardware ) which are
not included and sold separately.
R
:
bed I;
(Hollywood bed frame sold separately)

15
Converting crib to a twin bed II
You have the option to convert crib to a twin bed II.
1:Use the back rail as the headboard of twin bed II.
3:Connect the assembled parts and headboard of twin bed to the kits ( legs, long rails,and
hardware ) which are not included and sold separately.
2:Connect the left foot platform and the right foot platform to the rail which are not included and
sold separately.
$
(Hollywood bed frame sold separately)

FURNITURE TIPPING DETERRENT HARDWARE
HOW TO LOCK
16
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
WARNING
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted to the edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked to the brackets.

:
GN
:
G
&:
17
LIMITED WARRANTY
� Dream on Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
� This warranty covers 30 days from the date of original purchase.
� This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
� This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
� This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components
are broken or missing, DO NOT USE