Dream On Me 656 User manual

Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed are step by step instructions to help you.
quickly assemble your product.Before you begin we recommend
that you follow the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect parts during assembly please place them on a soft surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 656
1
s
Read all instructions before assembling crib.
Save instructions for future referrence.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788

2

.Read all instructions before assembling crib, keep instructions for future use.
.Upon completion of assembly be sure all screws, bolts and fastening devices have been
securely tightened. A frequent check should be made.
.Infants can suffocate in gaps between a mattress too small or too thick and product sides,
on soft bedding never add a mattress, pillow,comforter or padding.
.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8
inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the
.Failure to follow these warnings and the in structions could result in serious injury or death.
.Never use plastic shipping bag or other plastic film as mattress covers not sold and
intended for that purpose, as they can cause suffocation .
.Strings can cause strangulation! Never place items with a string around a child’s neck,
.Never use this product if there are any loose or missing fasteners, loose joints,broken
parts, or torn mesh/fabric. check before assembly and periodically during use.
Contact DREAM ON ME for replacement parts and instructional literature if needed.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Discontinue use of the product when child is able to climb out or reaches the height of
.When child is able to pull to standing position,set mattress/base to lowest adjustment
position and remove bumper pads, large toys,and other objects that could serve as steps
for climbing out. A child can trap parts of the body or clothing on loose fasteners .
.Never use a water mattress with this product.
.If refinishing,use a non-toxic finish specified for children’s products.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
WARNING !
.Never place product near window where cords from blinds or drapes can strangle a child.
MADE IN CHINA
35in (890mm).
mattress shall be taken from seam to seam or edge to edge where appropriate.
such as hood strings or pacifier cords. Never suspend strings over product or attach
strings to toys.
.
.
.
Never place additional padding under an infant
.
To help prevent strangulation tighten all fasteners.
.
A child can trap parts of the body or clothing on loose fasteners.
.
Follow warnings on all products in a crib .
See head panel & mattress support of the product for warnings.
Replace teething rail if damaged,cracked or loose.
3
Read all instructions before use of the changing table, add-on changing unit, or contoured
changing pad. For this changing table,the maximum weight of the child is 30lbs.
Do not use changing table, add-on changing unit, or contoured changing pad if it is
damaged or broken.

8
$
4
890

5
CONNECTION HARDWARE
a: 2” b: 1-3/8”Allen head bolt (20 pcs) c: 2-3/8”Allen head bolt (6 pcs)Allen head
bolt (3 pcs)
f:Wood dowels (20pcs)
q:Allen wrench
(1pc)
d:3-1/2”Allen head bolt (6 pcs) e:Barrel nuts (12 pcs)
k: 3/4”Allen head bolt
(4 pcs)
h:1-3/8” Screw (3 pcs) i:Knob (3pcs)
g:Cross screw (24pcs) j:Shelf support (4pcs)
PARTS ENCLOSED IN CARTON
ALeft head board
A1:Left back leg (1pc)
A1
A2
A3
B1
B2
A2:Left board (1pc)
A3:Left front leg (1pc)
BChanger side CRight back leg (1pc)
B1:Left (1pc) B2:Right (1pc)
l:Washer
(2pcs)
m:Bolt (2pcs) n:Belt (1pc) p:Tip over
restraints (1pc)
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE Do Not Use Power Drills or Drivers
J
3

6
GDrawer HBack rail (1pc)
JFront rail (1pc) KMetal spring support platform (1pc)
G1:Front panel (3pcs)
G2:Left side panel (3pcs)
G3: Right side panel (3pcs)
G4:Back panel (3pcs)
G5:Bottom panel (3pcs)
LPad (1pc)
DChanger middle panel EChanger bar FChanger shelf
D1:Top bar (1pc)
D2: Panel (1pc)
D3:Bottom bar (1pc) E2:Middle bar (2pcs)
E1:Bar (5pcs)
E3:Back bottom bar (1pc)
F1:Changing surface (1pc)
F2:Changer middle shelf (1pc)
F3:Changer bottom shelf (1pc)
The bottom bar (1pc)
M
M
E2
E3
E1 F1
F2
F3
G1
G2
G3
G4
G5
D1
D2
D3
G
JK
F

7
CRIB ASSEMBLY
STEP 1
Attach The changer bar(E1&E2&E3) ,
and The changer middle(D1&D3)
toThe changer side (B2) using wood
dowels (f),bolts(b) and allen wrench (q).
Model shown is example only.
Styles may vary .
Lay down the assembled parts
on the floor .
Slide The changing surface (F1)
into the groove in (B2) along the
groove between (E2) and (E2) .
Slide (D2) into the groove in (B2)
along the groove between (D1) and (D3) .
Then slide (F3) into groove in
(B2) along the groove between
(E3) and (D3) .
STEP 2
Model shown is example only.
Styles may vary .
E1
E1
E1
E1
D1
D3
E2
E3
B2
E1
b
b
f
b
b
b
b
b
b
f
f
f
f
f
f
f
f
f
E2
F1E2
E3 E2
B2
D2
D1
D3
F3

8
STEP 3
Model shown is example only.
Styles may vary .
Attach The changer bar (E1&E2&E3) and
The changer middle (D1&D3) to The
changer side (B1) using wood dowels
(f),bolts (b) and allen wrench (q) .
Attach left back leg (A1) and
right back leg (C) to back rail (H)
using bolts (d) and barrel
nuts (e) .
STEP 4
Model shown is example only.
Styles may vary .
b
b
b
b
b
b
b
b
bb
d
d
d
d
f
f
f
f
f
f
f
B1
B2
H
A1
C
E1
E2
E1
E1
E1
E3
D3 D2
F3
F1
e
e
e
e
Insert the shelf supports (j) in the holes in the posts of changing table.
Then place the changer middle shelf (F2) inside the shelf support .
Tighten the screws in the shelf supports (j) .
CHECK THAT ALL BOLTS ARE TIGHTENED .
F2
j x4
j F2

9
STEP 5
Model shown is example only.
Styles may vary .
Connect the assembled parts of
STEP 4 to the assembled parts of
STEP 3 by using bolt (a) and allen
wrench (q).
Connect the assembled parts to
left board (A2) by using bolt (c),
barrel nuts (e) and allen wrench (q).
Attach the left front leg (A3) to the
left board (A2) using bolt (d),
barrel nuts (e) and allen wrench (q).
Locate the mattress support (K)with tabs .
Be sure the smooth side of the
mattress support (K) is faced upward .
Position the tabs of the mattress
support(K) to mount to the selected
position onto the legs .
Insert the bolts (k) , through the
tabs and into thread inserts ,
then tighten securely with allen
wrench (q) .
STEP 6
Model shown is example only.
Styles may vary .
k
A1
B1
A2
A3
C
H
d
c
a
a
a
c
d
e
e
e
e
H
C
B1
K
A1
A3

10
STEP 7
Model shown is example only.
Styles may vary .
Attach The front rail (J) to
The changer side (B1) and
The left front leg (A3) using
bolts (c),barrel nuts (e) and
allen wrench (q) .
Attach left side panel (G2) & right side
panel (G3) to back panel (G4) by
inserting cross screw (g) into the holes
on left side panel (G2) & right side panel
(G3) .
DO NOT tighten all .
STEP 8
Model shown is example only.
Styles may vary .
G2
g
G3
g
G4
g
g
c
c
c
c
J
A3
B1
e
e
e
e

11
STEP 9
Model shown is example only.
Styles may vary .
Slide the bottom panel (G5) painted side
up , into grooves of the left side panel
(G2) and the right side panel (G3) . In
the end , insert the bottom (G5) into the
groove of back panel (G4) .
G2
G3
G4
G5
Attach the front panel (G1) to the left side
panel (G2) and the right side panel (G3)
by inserting cross screws (g) into the
holes on left side panel (G2) & right side
panel (G3) .
Inserting the bottom panel (G5) into the
groove of the front panel (G1) .
Tighten all the screws .
Assemble the rest two drawers follow step 8,9,10 .
STEP 10
Model shown is example only.
Styles may vary .
Attach the knob (i) to the front panel (G1) by
screw (h) .
G2
G3
G4
G5
G1
i
h
g
g
g
g

12
Model shown is example only.
Styles may vary .
STEP 11
1.Slide the drawers into rails on head board (B1&B2) .
2.Assembly the belt (n) to the changer side (B1& B2) using washer (l) and bolt (m) .
3.Add the pad (L) .
4.Put the child on the pad,then insert safty restraint system of the tape across child's waist.
The tightness can be adjusted by increasing the tension of the tape.
ml
n
NOTE :PLEASE PUT THE
DRAWER WITH CLEAN
STICKER AS THE FIRST ONE.
G
L
G
G
B1
B2
Note:please assemble the longer belt to the far side from the crib.
longer belt
shorter belt

Converting crib to a toddler bed
！
Failure to follow these warning and the assembly instructions could result in serious injury or
death from entrapment or strangulation. DO NOT place bed near windows where cords
from blinds or drapes may strangle a child. DO NOT place items with a string,cord,or ribbon
around a child’s neck,such as a hood, strings or pacifier cords. DO NOT suspend strings
over a toddler bed for any reason.
WARNING FOR TODDLER BED USE
The mattress intended for use on the bed shall be a full-size crib mattress having the
dimensions of 51-5/8” (1310 mm) in length and 27-1/4”(690mm) in width and thickness of
4” (100mm) or a greater thickness as specified by the manufacture. The minimum age of the
intended user shall not be less than 15 months and the maximum weight shall not be greater
than 50ibs(22.7kg).
13
Model shown is example only.
Styles may vary .
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.
M
cc
e
e
c

8
14

Converting crib to a day bed
15
Model shown is example only.
Styles may vary .
Model shown is example only.
Styles may vary .
You have the option to convert crib to a day bed
1:Remove the front rail (J).
2:Install the mattress support (K)
in its lowest position.
3:Assembly the bottom bar (M) to left
front leg (A3) and changer side
(B1) using allen head bolt (c) and
barrel nuts (e) as is shown .
You have the option to convert crib to a
full size bed I.
3.Use the front rail as the footboard of
full size bed;
4.Use the back rail as the headboard of
full size bed;
5.Connect the front rail and the back rail
to the kits ( legs, long rails,and hardware)
which are not included and sold separately.
Converting crib to a full size bed l
c
c
eA3 M
B1
A right front leg is available for this bed.
Please see your crib retailer,visit
www.dreamonme.com or contact
Consumer Care for more information.
This bed uses Style #696 Leg.
1.Remove the changing table from the crib.
2.Assemble the right front leg(#696, sold
separately) to the front rail.
(Hollywood bed frame sold separately)

16
Model shown is example only.
Styles may vary .
Converting crib to a full size bed II
You have the option to convert crib to a full size bed II
1:Use the back rail as the headboard of full size bed.
3:Connect the assembled parts and headboard of full size bed to the kits ( legs, long rails,and
hardware ) which are not included and sold separately.
2:Connect the left foot platform and the right foot platform to the rail which are not included and
sold separately.
PARTS REQUIRED TO COMPLETE STEP
LEFT FOOT PLATFORM
POST x 1
NOT INCLUDED
POST x 1
NOT INCLUDED
RIGHT FOOT PLATFORM POST x 1
NOT INCLUDED
RAIL
(Hollywood bed frame sold separately)

FURNITURE TIPPING DETERRENT HARDWARE
HOW TO LOCK
17
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
WARNING
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted to the edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked to the brackets.

8
18

19
LIMITED WARRANTY
� Dream on Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
� This warranty covers 30 days from the date of original purchase.
� This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
� This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
� This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components
are broken or missing, DO NOT USE