dreambaby F2029 User manual

INSTRUCTIONS
Cosmopolitan Security Gate
With Stay-Open Feature
F2029
WARNING
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
WARNING — Incorrect installation can be dangerous;
WARNING — Do not use the safety barrier if any components are
damaged or missing;
WARNING — The safety barrier must not be fitted across windows;
WARNING — Never use without mounting cups;
This safety gate conforms to EN 1930:2011;
This safety gate is for domestic use only;
This safety gate has been designed for use with children up to 24 months of age;
Never use with a child able to climb over or dislodge/open the gate;
The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound;
If the gate is used at the bottom of the stairs to prevent the child climbing up the
stairs, it must be placed on the lowest stair;
If the gate is to be used at the top of the stairs to prevent the child falling down the
stairs, it must not be placed on any stair below the level of the top stair;
This gate has a manual close system.
This gate is intended for indoor use and is not to be exposed to outdoor elements.
Caution: As part of the pressure-mounted gate engineering, there is a construction
bar at the base of the gate opening. Toavoid tripping or falling, always use extra
caution to step over this construction bar at the base of the gate, particularly when
gate is positioned at the top of a staircase.
Can be used in conjunction with a Dreambaby
®
Watch-the-Step
®
Gate Ramp (F837)
to help avoid tripping.
PARTS LIST
A - Gate Panel
B - Upper Locking Set
C - Gate Release Switch
D - Smart Open-Hold System
E - Right Upper Corner
F - Tension Knobs
G - Bolts with Rubber Pads
H - Mounting Cups
I - Double-sided Adhesive Tape
J - Gate Frame
K - Lower Locking Set
THE GAP IN THIS GATE IS
NOT A FAULT.
THE GAP WILL DISAPPEAR
WHEN THE GATE IS
CORRECTLY INSTALLED.
NOTICE TO CUSTOMERS
WARNING: This package
contains small parts and sharp
points in an unassembled state.
Keep out of reach of children.
Adult assembly required.
IMPORTANT NOTICE
to Customers
Thegap in this gate is NOT a fault.
Thegap will disappear when the
gateis correctly installed.
Referto enclosed instructions for
correctinstallation procedures.
F - Gate Notice
F x 4
H x 4
G x 4
I x 4
x 4
DBC
A
F
G
I
H
E
J
K

F2029F2029F2029
F1981 - 9cm (3.5in)
F1982 - 18cm (7in)
F1983 - 27cm (10.5in)
Gate Extensions
(sold separately)
Gate
75 - 84cm (29.5 - 33in)
3A
1. Measure the width of the opening of where you intend to install the gate. For openings over 84cm (33in) select the
appropriate Gate Extension(s), sold separately. Some examples are shown below.
F2029_082015
Fasten mounting cups to
the wall with screws or
double-sided adhesive tape.
3C Warning: Never use gate
without Mounting Cups.
Bolt with
Rubber Pad
Mounting
Cups
Top view of gate
Side view of gate
3. Place the gate in the opening so that the bottom of the Gate Frame is completely flat on the floor (3A), and it is perpendicular
to the openings and the floor (3B). Then fasten the Mounting Cups to the wall (3C) with screws or double-sided adhesive tape.
Note: Ensure that they are are aligned vertically, so that the Mounting Cups at the top are directly above the ones at the bottom.
If the safety barrier is
used at the bottom of the
stairs to prevent the
child climbing up the
stairs, it must be placed
on the lowest stair.
If the safety barrier is
used at the top of the
stairs, it should not be
positioned below the
top level.
3B
Bottom of stairs
Top of stairs
75 - 84cm
(29.5 - 33in)
84 - 93cm
(33 - 36.5in)
129 - 138cm
(50.5 - 54.25in)
+ F1983F1983 +F1981 +
NOTE: Carefully read
point 2, regarding
Extension Pins.
For F1981 Gate Extension,
insert “long end” of Extension
Pins into Gate Frame.
For F1982 and F1983
Gate Extensions, insert “short
end” of Extension Pins into
Gate Frame.
2. To connect the Gate Extensions, insert Extension Pins into the holes on the
outside of the Gate Frame.
For Gate Extension - F1981 : insert “long end” of Extension Pins into Gate Frame.
For Wider Gate Extensions - F1982 and F1983 : insert “short end” of Extension
Pins into Gate Frame.
Tension
Knob
Extension Pin
Gate
Extension
Gate Frame
2A
WARNING:
A maximum
of 2 Gate
Extensions
can be used,
1 on either
side of gate.
Do NOT install
2 Gate
Extensions on
the same side
of gate.
INSTALLATION
12
1 2

Lift Gate Panel up
to open
4. Centre the gate in the opening.
The distance from the Tension
Knobs positioned at the bottom of
the gate, to the walls, should be
equal (4A).
5. Tighten both of the Tension Knobs by
turning them clockwise at the same
time (5A and 5B). Note: make sure
that the bottom of the Gate Frame
remains completely flat on the floor.
Ensure gate is securely fastened at
both top and bottom.
6. Tighten the Tension Knobs until the 2 Indicator Arrows, located on the
Upper Locking Set and on the Right Upper Corner, align horizontally (6).
Keep 1mm (0.04in) gap between Upper Locking Set and Upper Right
Corner (6).
INSTALLATION
OPERATION
Distance should be equal
Tighten
inward
Tension Knob
Gate Frame
Keep this gap about 1mm (0.04in)
4A 4B
6
7. To open the gate: Slide the Gate Release Switch (7A). Lift the Gate Panel upward (7B). Gate swings open in both directions (7C).
7B
Gate Release
Switch
Slide
7A
5B
5A
Gate opens in
both directions
7C

Upper
Locking Set
8A
Gate
Panel
Lower
Locking Set Gate Frame
8B
OPERATION
8. Close the gate until it is fully locked with
Upper and Lower Locking sets engaged.
9. For easy walk through use Smart Stay Open System:
To engage the Smart Stay Open System swing gate
in chosen direction to its maximum opening.
Gate will stay open (9A/9B). Close as required.
Caution: Keep gate closed when children
are present.
Gate in CLOSED position
Swing to OPEN positions
TOP VIEW OF GATE
9A 9B
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to statutory
consumer guarantees and does not seek to exclude or limit them. These
guarantees include that Tee-Zed’s products are of acceptable quality. This
Tee-Zed product is for the specific purpose detailed in the instructions
and packaging and Tee-Zed considers use outside of that purpose to be
abnormal use. To the maximum extent permitted by law, Tee-Zed does not
accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other than in
accordance with the supplied installation and removal instructions; or
• arising under the law of tort or contract.
MAINTENANCE & CARE
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check Tension Knobs, Rubber Pads and Mounting Cups to make sure the gate is securely in place and closes
correctly. Adjust as required.
• Only use Dreambaby®spare parts. Any additional and replacement parts should be obtained from Tee-Zed Products.
• To clean, wipe surface with a damp cloth using mild detergent and warm water.
Never clean with abrasive, ammonia, bleach or spirit based type cleaners.
Dreambaby
®
products by
Made in Hangzhou, Zhejiang, China.
©2015 Tee-Zed Products Pty Ltd
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
facebook.com/Dreambabysafety
youtube.com/user/Dreambabytv
Tee-Zed Products Pty Ltd
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: [phone]
[e-mail]
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre Auckland
New Zealand Tel: [phone]
[e-mail]
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: [phone]
[e-mail]