DRIFLOWER HARVEST RACK User manual

1
5
THE HARVEST-RACK HARDWARE KIT
• ASSEMBLY INSTRUCTIONS •
PARTS INCLUDED
Harvest-Rack™ Hardware:
2- Harvest-Rack Brackets ……….………… ( A )
2- Harvest-Brackets …….………………………… ( B )
PARTS NOT INCLUDED
(AVAILABLE AT HOME IMPROVEMENT STORES )
YOU WILL NEED THE FOLLOWING
WOOD
CUT 2 x 3 STUDS TO THE FOLLOWING LENGTHS
8- 2 ft. pieces (2” x 3” x 24” ) ……….………..…… ( X )
2- 3-5 ft. vertical posts (2” x 3” x var.*) ..… ( Y )
*variable vertical height based on cola/branch length
2- 5-7 ft. cross-pieces (2” x 3” x var**) ….. ( Z )
**variable cross section based on stick length
SCREWS
28 - 1 ” Construction Screws ……………… ( ¡)
24 - 2 ” Construction Screws ……………… ( ø )
TOOLS NEEDED (NOT INCLUDED)
Power Driver/Drill
Pencil
Tape Measure
Square/Right Angle
NOT INCLUDED
14
/
12
/
Square/Right Angle
LEG ASSEMBLY
5
2
Reinforce leg strength by inserting two screws ( ¡ ) through the
two holes pictured above. Repeat for both leg assemblies.
x2
( A )
( X )
¡(x3)
¡(x3)
( X )
x2
¡(x2)
( X )( X )
( A )
x2
Use a 2 ft. piece (X)across the inside of the leg assembly
and connect with screws (ø) to stabilize the Harvest-Rack.
Repeat for both leg assemblies.
( X )
ø(x2) ø(x2)
Diagonally place two 2 ft. pieces (X)into the bracket (A)
until corners touch the GUIDE-PIECE, evenly spaced.
Using six screws ( ¡ ), connect the legs to the bracket (A)
through the side holes into the legs. Repeat for both brackets.
Lay the Harvest-Rack Bracket (A)on a flat surface (open-side up)
and place a GUIDE-PIECE in the center.
( FLIP OVER )
4
3
Begin by cutting 2x3 studs to the above lengths.
The length of the cross-pieces (Z) will be determined by stick length,
so if you’re using 8 ft DriFlower Sticks, cut cross-pieces to 84” (7 ft).
2” x 3” x 24”
2” x 3” x 60” - 84” (var.)
2” x 3” x 36” (var.)
( X )
8 pcs.
( Y )
2 pcs.
( Z )
2 pcs.
PREPARE TO BUILD YOUR HARVEST-RACK
WOOD
&
SCREWS
NOT
INCLUDED
Congratulations!
The DriFlower Harvest-Rack Hardware Kit is where streamlining
and organizing your harvest begins.
MAKE SURE TO READ ALL OF THESE INSTRUCTIONS
After reading the instructions, cut all wood and make sure you
have the correct size and amount of screws (listed on front page).
After cutting all wood, you will put together the leg assemblies
and then the truss assembly.
It is important to use a GUIDE-PIECE during the leg assemblies
to set the legs in the correct position.
The GUIDE-PIECE is temporary and will not be attached so this
can be any of the other 2x3 pieces not being used.
The space the GUIDE-PIECE creates will be used to connect the
leg assembly to the truss assembly.
Take your time. Measure twice, cut once. This Harvest-Rack is
about to transform the way you harvest your flower!
MAKE YOUR CUTS
( ¡)
28 screws
( ø )
24 screws

6
8
9
2
7
www.driflower.com ©2021
7
ø(x4)
ø(x4)
( Y )
( Y )
( Z )
( Z )
( Z )
( Z )
Measure and mark one foot from the bottom of the vertical post (Y).
The measurement from the top of the vertical post to this mark will be
the average cola length. We suggest at least 24”.
Screw the two cross-pieces (Z)to both vertical posts (Y)
at the bottom and at the 1 foot marked line.
The length of these cross-pieces should be 1 foot shorter
than the aluminum stick being used to hold hangers.
2
one foot from the bottom of the vertical post (Y)
1 FT.
AVG.
COLA
LENGTH
( Z )
( Z )
( Y )
x2
TRUSS ASSEMBLY
For structural support, flip the truss over and attach two
2 ft. pieces (X)diagonally to the cross-pieces.
Make sure to do this on the inside, between the vertical posts,
for maximum efficiency.
On each side of the truss, place a leg assembly around the
vertical post just beneath the upper cross-piece. The
vertical post will fit into the Harvest-Rack bracket while the
upper cross-piece rests atop the bracket.
x2
Screw the leg assemblies to the truss to
secure the balanced Harvest-Rack.
For structural support, flip the truss over and attach two
( FLIP OVER )
( X )
x2
ø(x2) ø(x2)
¡(x4) ¡(x4)
Align the stick slot of the Harvest-Bracket (B)with the top
of the vertical post (Y)and attach with two screws ( ¡ ) to
the outside of the riser. Repeat for the other side.
ALIGN
( Y )
( B )
¡(x2) x2
Place a DriFlower Stick on the completed Harvest-Rack
and get ready to level up!
For a video of this assembly and to view other videos
and instructions, please visit us online at:
https://driflower.com/support/brochures-and-manuals/
11
10