DRIFLOWER THE PRO HARVEST-RACK User manual

1
5
TOOLS NEEDED (NOT INCLUDED)
Phillips Screwdriver
Pliers / Wrench (or)
Ratchet Wrench
Sockets #10, 3/8
NOT INCLUDED
2
Attach a Harvest-Bracket (Y) to each Vertical Post (C) with
smaller screws and nuts (!+ ")as pictured above.
Attach the two Cross Bars (B) to the leg assemblies by inserting
each end through the open slots and aligning the holes. Once
aligned, insert the 2 1/4” screws (¥)down from the top through
the six holes (per side) so they align with the cross bars.
Time to shine, keep it in line.
Make sure the cross bars are “face up” and “DriFlower” is legible
on each cross bar so that the holes match to each side.
3
( A )
Begin by aligning legs pieces (A) with the pre-drilled leg holes
in the Outer Pro Harvest Bracket (T).
Insert the 2 1/4” screws (¥) through the outer bracket, through the
legs, and then connect the Inner Pro Harvest Bracket (G).
Attach the nuts (") and hand tighten.
PREPARE TO BUILD YOUR
PRO HARVEST-RACK
Congratulations!
The DriFlower Pro Harvest-Rack is designed to
streamline and organize mid to large scale harvests.
MAKE SURE TO READ ALL OF THESE INSTRUCTIONS
After reading the instructions, make sure you have the
correct pieces and screws for each assembly
(listed on the front page of these instructions).
.
You will start by putting together the leg assemblies.
Then, attach the dual cross bars to the legs.
Lastly, add the adjustable, vertical posts to the rack.
KEEP IT LIGHT BEFORE MAKING IT TIGHT
When assembling the Pro Harvest-Rack, we recommend
not tightening all the way. Simply, hand tighten or loosely
tighten the connections so there is adjustability when
connecting other pieces.
Once the base is assembled, then tighten all connections
with wrench, screwdriver or other recommended tools.
KEEP IT IN LINE AND YOU’LL BE FINE
Keeping a visual check on your center alignment will
make for easy assembly and usage. For example, keep
the DriFlower stickers facing outward and right-side up so
they can be read normally. Each hole is aligned with the
proper placement of the cross bars.
Take your time. This Pro Harvest-Rack is about to
improve the efficiency of your harvest!
BUILD YOUR LEG ASSEMBLIES
THE PRO HARVEST-RACK™
• ASSEMBLY INSTRUCTIONS •
PARTS INCLUDED
The Pro Harvest-Rack pieces :
METAL BARS
4- 30” Legs (1.5”x .75”) ………..…………..….……… ( A )
2- 91” Cross Bar (1.5”x .75”) ……………….…….… ( B )
2- 36” Vertical Posts (1.5”x .75”) ……………….. ( C )
1- 91” Stick (Hang Bar) (1.5”x .75”) …..…….… ( D )
BRACKETS
2- Harvest-Brackets ……………………….………… ( Y )
2- Inner Pro Harvest-Rack Brackets …… ( G )
2- Outer Pro Harvest-Rack Brackets ….. ( T )
SCREWS & NUTS
20 - 2 ” Phillips Head Screws …..….…….… ( ¥ )
4- 1 ” Phillips Head Screws …….….…..… ( !)
24 - #10 Nuts ……..…………………………..…….…… ( ")
2 - Keeper Pins ……..……………………..…….…… ( ƒ )
)
2
ASSEMBLE VERTICAL POSTS
™
14
/
( T )
( ")
( ¥ )
( B )
( ¥ )
( ")
( A )
( T )
(
"
)
( #)
( C ) ( C )
Attach a Harvest-Bracket (Y) to each Vertical Post (C) with
smaller screws and nuts (
( C )
THE PRO HARVEST-RACK™
( A )
14
/
( G )
x2
( B )
x2
( ")
Attach a Harvest-Bracket (Y) to each Vertical Post (C) with
smaller screws and nuts (
( C )
( C )
( Y ) ( Y )

6
2
www.driflower.com ©2021
Slide the Vertical Posts (C) into the slots on the
Pro-Harvest Brackets and insert the Keeper Pins (ƒ) to hold
at the appropriate height.
Minding the details…
Facing the verticals so that the Harvest-Brackets face outward,
away from the center, will give you wider support and will provide
additional safety precautions.
CONNECT VERTICAL POSTS TO BASE
Once all connections have been tightened, place your
aluminum Stick (D) in the Harvest-Bracket slots so that the
stick is evenly distributed with equal measure on each end.
Proper placement helps stabilize the stick as it is seated
on the Pro Harvest-Rack.
Bring the rack to your flower and start harvesting!
To view these instructions online, please visit us at:
https://driflower.com/support/brochures-and-manuals/
4
5
Once all parts have been connected, tighten each screw
and nut using the appropriate wrenches and drivers.
( ƒ )
2
(
ƒ
)
x2
***KEEP HANDS AWAY FROM THE BRACKETS AND AVOID
PUTTING ANY PART OF THE BODY BETWEEN
THE STICK (hanger bar) AND VERTICAL SUPPORTS.
( C )
TIGHTEN ALL SCREWS AND NUTS