Congratulations! Say hello to your new best bud,
The DriFlower LIL’ BUDDY Personal Rolling Harvest-Rack.
MAKE SURE TO READ ALL OF THESE INSTRUCTIONS
After reading the instructions, make sure you have the
correct pieces, nuts and bolts for each assembly
(listed on the front page of these instructions).
.
You’ll start by building the base-assembly.
Then, connect the Vertical Posts to the base-assembly.
Lastly, attach the Hanger-Bar and you’re done!
NO NEED TO STRAIN - HAND TIGHTEN FOR LESS PAIN
When assembling, we recommend not fully tightening all
nuts and bolts until all pieces are assembled.
Simply hand-tighten (or loosely tighten) the connections so
there is adjustability when connecting other pieces.
Once the rack is fully assembled, then tighten all
connections with the recommended tools.
**KEEP IT IN LINE AND YOU’LL BE FINE
Keeping a visual check on the center alignment of your rack
will make for easy assembly and usage.
For example, there are two sets of pre-drilled holes on the
bottom of the Vertical Posts that align with holes in the
Cross-Bar and the holes in the Wheel-Bars.
When attaching the Vertical Posts to the base assembly,
** make sure all the pre-drilled holes line up.
Another important alignment, the Hanger-Bar should be
centered for proper weight distribution on the rack.
*** Make sure the Hanger-Bar is directly over the Cross-Bar.
Take your time. This Harvest-Rack is about to transform the
way you harvest your flower!
RECOMMENDED TOOLS (NOT INCLUDED)
Ratchet Wrench
3/4” Socket
3/4” Wrench
Attach both Wheel-Bars above the center holes of the Cross-Bar
using 3 3/4” hex bolts (¡), washers (w) and 1/2” hex nuts (n) on
each side. Tighten by hand.
Time to shine, keep it in line.
*Make sure to attach the Cross-Bar underneath the Wheel-Bars
so that the Cross-Bar is on the same side as the Castor Wheels.
Begin by attaching all four castors (O) to the two Wheel-Bars (A).
Thread the castor bolt through both holes on each end of the Wheel-
Bars and fit the castor washer and nut on the top end of the castor
bolt (as pictured) tighten by hand.
PREPARE TO BUILD YOUR
ROLLING HARVEST-RACK
LIL’BUDDY
PERSONAL ROLLING HARVEST-RACK™
• ASSEMBLY INSTRUCTIONS •
PARTS INCLUDED
The LIL’BUDDY Harvest-Rack pieces :
METAL BARS
2- 24” Wheel-Bar (1.5”x 1.5” sq.) ….…….……… ( A )
1- 24” Cross-Bar w/ sticker (1.5”x 1.5” sq.) .….. ( B )
2- 48” Vertical-Post (1.5”x 1.5” sq.) ………….…. ( C )
1- 32” Hanger-Bar (1.5”x .75”) ………….…….… ( D )
WHEELS
4- Locking Castors ………….…..………..……….… ( O )
NUTS & BOLTS
6- 3 ” Hex Head Bolts (1/2) ……..….…..…… ( ¡)
2- 3” Hex Head Bolts (1/2)……….……..…..…… ( ¥)
20 - ” Washers …………………….…………….…… ( w)
12 - ” Hex Nuts (13) …………..….……….….…… ( n )
CONNECT VERTICAL POSTS TO BASE-ASSEMBLY
** IMPORTANT NOTE: VERTICAL POSTS HAVE TWO SETS OF
HOLES ON THE BOTTOM OF EACH POST THAT ALIGN WITH
THE HOLES OF YOUR BASE-ASSEMBLY.
**Make sure to align your Vertical-Posts so that both sets of holes
line up with the off-center holes in the Wheel-Bars and the pre-
drilled holes of the Cross-Bar (sticker side).
Use the 3 3/4” hex bolts (¡), washers (w) and 1/2” hex nuts (n) on
each side of the Wheel-Bar directing the bolt thread toward the
inside of the rack. Tighten by hand.
