Drolet DG04900 User manual

DV30
DV45
DV
30
DV4
5
Model Code Gas
DV30 DG04900 Gas "E" Liquefied propane gas (LPG)
DV45 DG04905 Gas "E" Liquefied propane gas (LPG)
INSTALLATION AND
OPERATING INSTRUCTIONS
GAS WALL MOUNTED ROOM HEATER
WARNING: If the information in these instructions are not followed
exactly, a re or explosion may
result causing property damage, personal injury
or death.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS:
- Shut off the gas supply at the gas source.
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone
in your building.
-Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a qualified
installer, Service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
The coating selected to provide longer life to the heat exchanger
may smoke slightly upon initial ring.
Please provide adequate ventilation if this occurs.
The appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile home, where not prohibited by local
codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a
certied kit is used.
WARNING: Operation of this stove without the properly installed, furnished vent system and vent cap could result in Carbon Monoxide (CO) poisoning and
possible death. For your safety, this stove and the vent system should be inspected at least annually by a qualied service technician.
This unit is for residential use only and is not approved for installation in greenhouses, or environments involving dusty, wet, corrosive, or explosive
conditions. Such conditions will invalidate the warranty and may create unsafe conditions.
Installation, maintenance, service, trouble shooting and repairs must be performed by a qualied service agency.
Mr./Mrs. Homeowner, DO NOT attempt any of these procedures yourself as this could expose you to property damage, personal injury, or loss of life and
will invalidate all warranties.
DG04905-15-08-2019A

Drolet-DG04905 3
TABLE OF CONTENT
INTRODUCTION ....................................................................................................................... 6
PRODUCT IDENTIFICATION .................................................................................................... 7
SPECIFICATIONS, DIMENSIONS AND ADVERTISING ........................................................... 7
PRODUCT FEATURES.............................................................................................................. 8
FUNCTIONAL WIRING DIAGRAM............................................................................................ 9
PRODUCT FEATURES............................................................................................................ 10
INSTALLATION........................................................................................................................ 10
MINIMUM CLEARANCES FROM COMBUSTIBLES.............................................................. 10
VENT TERMINAL CLEARANCES ........................................................................................... 11
INSTALLATION WARNING...................................................................................................... 12
GENERAL INFORMATION...................................................................................................... 12
INSTALLATION PROCEDURE ................................................................................................ 13
INSTALLATION PROCEDURE ................................................................................................ 14
GAS CONNECTION ................................................................................................................ 16
OPERATION ............................................................................................................................ 17
TO TURN OFF GAS TO APPLIANCE ..................................................................................... 17
CLEANING AND MAINTENANCE........................................................................................... 18
GAS CONVERSION INSTRUCTION ....................................................................................... 20
ADJUSTMENTS ...................................................................................................................... 21
CHECKING THE SUPPLY PRESSURE................................................................................... 22
TROUBLESHOOTING............................................................................................................. 24
WARRANTY ............................................................................................................................ 25
PARTS LIST............................................................................................................................. 26

Drolet-DG049054

Drolet-DG04905 5

Drolet-DG049056
This gas appliance must not be connected to a chimney ue serving a separate solidfuel burning appliance.
IMPORTANT FOR YOUR SAFETY
• Improper installation, adjustment, alteration, service, or maintenance can cause property
damage, personal injury or loss of life. Refer to this manual.
• Do not connect this unit to a chimney flue serving a separate solid-fuel burning appliance.
• Installation and service must be performed by a qualified installer, service agency, or the gas
supplier.
Do not use this appliance if any part has been under water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the control system and any gas control which has been
under water.
INTRODUCTION
This is a gas-red, room heaters that will operate safely and provide an efcient source of heat when installed,
operated and maintained as recommended in these installation and operating instructions. Read these
instructions thoroughly before installing, servicing, or using the appliance. If you do not understand any part of
these instructions consult local authorities, other qualied installers, service technician, the gas supplier or the
manufacturer.

Drolet-DG04905 7
PRODUCT IDENTIFICATION
SPECIFICATIONS, DIMENSIONS AND ADVERTISING
These units are independent gas appliances for space heating. They use an atmospheric burner with an airtight
combustion chamber. This guarantees maximum safety because it does not allow exhaust fumes or gas leak
in the habited environment. The intake of the combustion air and the exhaust of the combustion fumes takes
place outside the environment through two concentric tubes, thanks to the balanced draft created by the
ascending force of the fumes. They can be installed in narrow spaces and are equipped with a humidifying
tray. They are assembled, in the factory, for operation with Gas "E" (LPG), but can be converted for Gas "A"
(LNG) operation, using the nozzle kit supplied.
The thermostatic ignition/control/regulation valve, controls all main functions and automatically shuts off the
gas supply in case of malfunction.
The control panel allows you to switch on the appliance’s electrical power (appliances with tangential fan or
timer only), to start and stop it manually or automatically using the thermodisc, to set its heating power and
start/stop the fan, adjust the room temperature setting and restore operation after a malfunction.
In Canada, the CSA C22.1 Canadian National Electrical Code and in the U.S.A, the NFPA 70 National Electrical
Code are to be followed in the absence of local code requirement.
cabinet
Back
Control panel
door
grill
Guard
Burner
inspection
holes
Blower
coverage
Front
cabinet
A
C
B
Model Input
Nom./Red.
kW
A
Width
B
Depth
C
Height
Gas
Connection
Type
gas
MAX wall
thickness
MIN wall
thickness
DV30 3,49/1,42 25,27 8,85 33,77 1/2” Gas "E"(LPG) 35,43 5
DV45 5,11/2,04 32,36 8,85 33,77 1/2” Gas "E"(LPG) 35,43 5
LNG: Liquefied Natural Gas
LPG: Liquefied Propane Gas

Drolet-DG049058
Room heater DV30
Gas type Gas A
(LNG)
Gas E
(LPG)
Max heating value Btu 9300 9300
Min heating value Btu 4740 4740
Minimum gas pressure before valve W.C. 3.5 8.0
Maximum gas pressure before valve W.C. 8.48 21.2
Gas pressure after valve for max W.C. 4.0 10.0
Injector main burner / n.
Ø inch
Ø mm
1
0.059
1.50
1
0.037
0.95
Injector pilote burner n.
Ø inch
Ø mm
1
0.017
0.42
1
0.007
0.19
Voltage rating / mains frequency 120 V AC / 60Hz
Electrical consumption W/H 37
Annual fuel utilization efciency % 73,66
Reference standards "ANSI Z21 86-2016 • CSA 2.32-2016"
Predispose for GAS E
Intake pressure W.C. 11
Manifold pressure W.C. 10
Room heater DV45
Gas type Gas A
(LNG)
Gas E
(LPG)
Max heating value Btu 13750 13750
Min heating value Btu 7536 7536
Minimum gas pressure before valve W.C. 3.5 8.0
Maximum gas pressure before valve W.C. 8.48 21.2
Gas pressure after valve for max W.C. 4.0 10.0
Injector main burner n.
Ø inch
Ø mm
1
0.071
1.80
1
0.046
1.16
Injector pilote burner n.
Ø inch
Ø mm
1
0.017
0.42
1
0.007
0.19
Voltage rating / mains frequency 120 V AC / 60Hz
Electrical consumption W/H 55
Annual fuel utilization efciency t % 76,85
Reference standards "ANSI Z21 86-2016 • CSA 2.32-2016"
Predispose for GAS E
Intake pressure W.C. 11
Manifold pressure W.C. 10
NOTE: Minimum Gas Inlet Pressure for purpose of input adjustment.The efciency rating of the appliance is
a product thermal efciency rating determined under continuous operating conditions and was determined
independently of any installed system.
PRODUCT FEATURES

Drolet-DG04905 9
CL LINE CONNECTOR
CVT CONDENSER
EA IGNITION ELECTRODE
F FUSE
IMP MANUAL SWITCH
L PHASE
N NEUTRAL
O TIMER
TV FAN THERMODISC
VT TANGENTIAL FAN
BoS BULB OF SWITCH
45°
LN
V.T.
Ib
F
IMP
1A
TV
CL
120V~ / 60 Hz
LN
CAUTION: Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
IaIBoS
FUNCTIONAL WIRING DIAGRAM

Drolet-DG0490510
PRODUCT FEATURES
NOTICE: A qualied service person must install the heater. Follow all local codes.
CHECK GAS TYPE
Use only the type of gas indicated on the rating plate.
INSTALLATION
Before installing the heater, make sure you have the items listed below;
· Piping (check local codes)
· Sealant (resistant to propane gas)
· Manual shutoff valve
· Pipe wrench
The installation location shall provide the following;
A) adequate combustion and ventilation air, and
B) adequate accessibility clearances for servicing.
MINIMUM CLEARANCES FROM COMBUSTIBLES
·Power Driver
· Jig Saw
· High Temperature Silicone (outside)
5,90”
(150mm)
MINIMUM
5,90”
(150mm)
MINIMUM
5,90”
(150mm)
MINIMUM

Drolet-DG04905 11
VENT TERMINAL CLEARANCES
REFERENCE LETTER TO DRAWING CANADIAN INSTALLATIONS
1
U.S. INSTALLATIONS
2
A = Clearance above grade,
veranda, porch, deck, or balcony
12 Inches (30 cm) 12 Inches (30 cm)
B = Clearance to window or door
that may be opened
12 Inches (30 cm) 9 Inches (23 cm)
C = Clearance to permanently
closed window
12 Inches (30 cm) 9 Inches (23 cm)
D = Vertical clearance to ventilated
soft located above the terminal
within a horizontal distance of 2
Feet (61 cm) from the center line
of the terminal
18 Inches (46 cm) 18 Inches (46 cm)
E = Clearance to unventilated
soft
18 Inches (46 cm) 18 Inches (46 cm)
F = Clearance to outside corner 12 Inches (30 cm) 12 Inches (30 cm)
G = Clearance to inside corner 12 Inches (30 cm) 12 Inches (30 cm)
H = Clearance to each side
of center line extended above
meter/regulator assembly
3 Feet (91 cm) within a height
15 Feet (4.5m) above the meter/
regulator assembly
Clearance in accordance with
local installation codes and the
requirements of the gas supplier
I = Clearance to service regulator
vent outlet
3 Feet (91 cm) Clearance in accordance with
local installation codes and the
requirements of the gas supplier
J = Clearance to nonmechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
12 Inches (30 cm) 12 Inches (30 cm)
K = Clearance to a mechanical air
supply inlet
6 Feet (1.83 m) 3 Feet (91 cm) above if within 10
Feet (3 m) horizontally
L = Clearance above paved
sidewalk or paved driveway
located on public property
7 Feet (2.13m) A vent shall
not terminate directly above a
sidewalk or paved driveway that
is located between two single
family dwellings and serves both
dwellings
Clearance in accordance with
local installation codes and the
requirements of the gas supplier
M = Clearance under veranda,
porch, deck, or balcony
12 Inches (30 cm) permitted only if
veranda, porch, deck, or balcony
is fully open on a minimum of two
sides
Clearance in accordance with
local installation codes and the
requirements of the gas supplier
1In accordance with the current CSA-B149.1 Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code

Drolet-DG0490512
GENERAL INFORMATION
This appliance is airtight. The combustion air ows only
from the outside!
- DON’T use for placement, accessories or components
not foreseen by the manufacturer, it is dangerous.
- DON’T place the power cord on hot surfaces such as
air diffusion grids or exhaust pipes after installation. The
installer must inform the user on the behaviors to keep
during the appliance operation:
- DON’T overlap draperies, towels or anything else that
could cause a malfunction and prevent a good air circulation
in the environment.
- DON’T block-off the air inlet / outlet of the appliance with
linen or carpets.
INSTALLATION WARNING
This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or
mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases, unless a certied kit is used.
WARNING: This appliance should only be installed by a qualied installer.
The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1.
WARNING:· The appliance area must be kept clear and free from combustible materials, gasoline, and other
ammable vapors and liquids.
· Due to high temperatures, the appliance should be located out of trafc and away from furniture and
draperies.
· Children and adults should be alerted to the hazards of high surface temperature and should stay away to
avoid burns or clothing ignition.
· Young children should be carefully supervised when they are in the same room as the appliance.
· Clothing or other ammable material should not be placed on or near the appliance.
· Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the
appliance.
Installation and repair should be done by a qualied service person. The appliance should be inspected
before use and at least annually by a qualied service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and circulating air passageways of the appliance be kept
clean.
WARNING: Failure to position the parts in accordance with these diagrams, or failure to use only parts
specically approved with this appliance may result in property damage or personal injury.

Drolet-DG04905 13
Min.
5,90”
150mm
Min.
5,90”
150m
m
Min.
1,96”
50mm
a
b
c
d
1
2
3
INSTALLATION PROCEDURE
The installation steps are:
-Positioning the appliance
-Cutting the intake/discharge pipes to length
-Installing the ue and air intake pipes L = 18,90 (included)
-Installing the combined intake/exhaust pipe terminal
-Installing the gasket
-Installing the heater itself
-Electrical hookup
-Gas line hookup
WALL MOUNTING
(concentric pipes, combined terminal)
IMPORTANT: Convection heaters are intended for installation against the wall only (the intake and ue pipes
run through the wall).
Before starting the installation, make sure the diameters, total lengths and the terminals of the pipes are match
those indicated in the following page’s gure.
INSTALLING THE TEMPLATE AND BRACKET
- Place the paper template (included with this
unit) onto the wall and check the clearances
around the appliance.
- Mark the hole "a" on the paper template (3).
Make a small initial hole, then use a suitable
cutter to make the big hole for the pipes.
- Cut the pipes to length and fit them into
the hole.
- Fit the protruding lip of the template (1)
onto the pipes.
- Mark the hole "b" on the metal template
and drill it, then secure the template and
bracket (2) to the wall.
- Level the horizontal bracket and mark the
two external holes "c".
- Make the two holes “c" and secure the
horizontal bracket.
- Mark and drill the hole "d" and secure the
template.
Drill the hole as shown "a""b" "c" "d" in the above figure.
E F
MIN
1,96”
50mm
L
G
I
F
E
G
30
14,17” (360mm)
11,10” (282mm)
5,74” (146mm)
45
18,18” (462mm)
14,17” (360mm)
25,27” (642mm) 32,36” (822mm)
L
H
24,80” (630mm)
I 19,13” (486mm)
H2
GAS
24,80” (630mm)
19,13” (486mm)
5,74” (146mm)
DV

Drolet-DG0490514
Ø 5,11”
Ø 130mm
Ø 3,14”
Ø 80mm
18,89”
480mm
6,85”
174mm
6,85”
174mm
1
2
3
4
4
5
6
7
8
11
10
9
3
1
2
5 6
7
8
10
0,39”
10mm
1,96”
50mm
3.1
8.1
INSTALLATION PROCEDURE
These models of wall furnaces are designed for direct venting through a wall.Only venting components specically
approved for these furnaces may be used.
The ow of combustion gases and ventilation air must not be obstructed.
Vent terminal must be 18.0” away from an adjacent wall.
IMPORTANT: The appliance’s venting system should be inspected at least once a year and immediately
cleaned if necessary.
IMPORTANT: the vent-air intake system must be properly installed to insure proper and safe operation. The
vent-air intake system must also be properly re-installed and
Re-sealed to insure proper and safe operation.
WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specically approved with this appliance may result in property damage or personal injury.
After having established the nal position of the appliance, follow the instructions below
1. Create a hole for installation of the wall pass-through (7);
2. Cut wall pass-through (7) at the same depth of the wall;
3. Slide the pass-through (7) inside the wall;
4. Cut the larger pipe (6) as the same depth of the wall;
5. Cut the smallest pipe (5), longer than the pipe (6) as shown in the figure bellow;
6. Put the two centering guides (4) at the beginning and the end of the tubes;
7. Put the pipe (6) into the pass-through (7);
8. Fix the template (3, horizontally) to the wall, using a screw in each corner hole. Bend the four wall
pass-through alignment tab's (3.1) at a 90˚ angle
9. Fix the template (2) over the template (3)
10. Fix the bracket (1) on the template(2)
11. Bend the 4 alignment tabs (8.1) of the plate (8) and secure it to the external wall with screws (9)
12. Fix the terminal (10) to the plate (8) with screws (11)

Drolet-DG04905 15
WALL INSTALLATION
1. Remove the jacket (12) from the heater (13)
(see instructions below)
2. Fit the O-Ring gasket (14) around the flange
of support (2).
3. Align and insert the two nuts of bracket (1)
in the coresponding holes in the heater
(13). Make sure the bottom of the heater is
supported by the lower flange of the support
(2). Secure the heater to the support with two
nuts (15). Tighten the nuts (15) until the rear of
the heater slightly compreses the gasket (14).
If it is not compressed enough, the system
will not be airtight which can be hazardous
and cause malfunctions.
REMOVING AND REINSTALLING THE JACKET
REMOVING THE JACKET
1. Remove the tray (3).
2. Undo the screws (2) securing the jacket.
3. Remove the external jacket (1) by lifting it
completely off.
REINSTALLING THE JACKET
1. Fit it against the edge of the frame, slide
the front of the jacket onto the front of
the frame and push it fully.
2. Hold it in place and secure it to the heater
with the screw (2).
3. Restore the tray (3).
12
13
2
1
15
15
14
13
2
1
15
15
14
3
2
1

Drolet-DG0490516
FROM GAS
MASTER
APPLIANCE
GAS INLET
1/2” NPTPIPE
NIPPLE
GAS CONNECTION
We recommend using only new black iron or steel pipe,
check local codes. The gas supply line shall be sized
and installed to provide a sufcient supply of gas to meet
the maximum demand of the heater without undue loss of
pressure. The sealant used on the threaded joints of the
gas pipe must be a type resistant to the action of L.P.G.
This sealant should be applied lightly to main threads to
ensure excess sealant does not enter lines.
IMPORTANT: Hold the gas inlet of the appliance with
wrench when connecting it to gas piping and /or ttings.
CHECK AFTER GAS CONNECTION
WARNING: All gas piping and connections must be tested for leaks after installation or servicing.
All leaks must be corrected immediately.
• Make sure the control of the heater is in the “OFF” position.
• Test for leaks by applying liquid detergent to all joints. Check all joints from gas meter to thermostat
gas valve. (Bubbles forming indicate a gas leak)
• Correct any leak defect at once.
CAUTION: never use an open ame to check for leaks
PRESSURE TESTING SUPPLY LINE
ATTENTION: This appliance and its appliance main gas valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of ½ psi (3,5 kPa).
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a re or explosion may result causing
property damage, personal injury or loss of life.
A. This appliance has a pilot. When lighting the pilot, follow these instructions exactly.
B. Before lighting smell all around the appliance area for gas. Be sure to smell next to the oor because
some gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
• Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted
repair may result in a fire or explosion.
• Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.

Drolet-DG04905 17
OPERATION
LIGHTING INSTRUCTIONS / MILLIVOLT (SELF GENERATING)
1. Turn the thermostat knob "A" to 7 (maximum setting).
2. From the "off" position, push in gas control knob "B" and hold it in 30
secondes.
3. If you smell gas, STOP! Follow “WHAT TO DO IF YOU SMELL GAS” in
the safety information. If you don’t smell gas, go to the next step.
4. Hold in knob "B"and turn it counterclockwise towards the pilot position.
You should hear the spark/click during the ignition. You will see the
flame through the 3 viewing holes in the front jacket.
5. Repeat step "4"until you see a flame in the viewing holes
6. Continue to hold the gas control knob in for about one (1) minute after
the flame is lit.
7. Release the gas control knob "B". Pilot should remain lit. If pilot goes
out, repeat steps 4 thru 6.
- If knob does not pop up when released, STOP and immediately call your service technician or
gas supplier.
- · If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your
service technician or gas supplier.
8. When the pilot is stably on, turn the knob to the main burner ignition in On position and check that
the burner ignites.
9. The burner will stay on (changing its power automatically) until it reaches the temperature setting,
at which point the burner will turn off leaving only the pilot still on, ready to ignite the burner again
as soon the temperature falls. If you experience problems with ignition or operation, or the pilot
light goes out, the heater will go into SHUTDOWN mode, and will automatically shut off the gas
supply. Wait for 1 minute for the thermocouple interlock to cool down before repeating the ignition
procedure. This operation can only be repeated 3 times. If the heater doesn’t start after three
attempts, set the master switch to OFF and contact service technician or gas supplier.
"B"
"A"
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to it’s lowest setting.
2. "Turn off all electric power to the appliance if service is to beperformed"
3. Open cabinet door.
4. Push in gas control knob slightly and turn clockwise to "OFF".
5. Do not force.
6. Close cabinet door.

Drolet-DG0490518
CAUTION: DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE MANUAL SHUTOFF VALVE.
IMPORTANT:
• Do not dry clothes over the heater.
• Do not spray any aerosol near the heater when functioning. Do not store these elements near the
appliance.
• Do not touch grill to avoid burns.
• Avoid blocking air inlet and hot air outlet.
• Do not spill water over the heater as it may cause corrosion or damage.
• Do not touch vent cap while heater is operating, to avoid burns.
• If you smell gas, shut off control valve, open doors and windows and do not light any electrical items
near the heater. Call your Gas Supplier.
NOTE: It is normal for the new wall furnace to give some odor the rst time it is burned. This is due to the curing
of the paint and any undetected oil from the manufacturing process. It is recommended to burn a new room
heater for at least two (2) hours the rst time that it is used.
CLEANING AND MAINTENANCE
WARNING: Turn off heater and let cool before cleaning.
CAUTION: You must keep control areas and circulating air passageways of heater clean. Inspect these areas
of heater before each use. Have heater inspected yearly by a qualied service person. Heater may need more
frequent cleaning due to excessive lint from carpeting, bedding material, etc.
Verify proper operation after servicing.
Make sure the unit is working properly after the maintenance is completed.
Exterior
Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.
Air Passageways
Use a vacuum cleaner or pressurized air to clean.
Vent Cap
Use a vacuum cleaner or pressurized air to clean.
Pilot and Burner
Periodically visually check the pilot and burner ames (View ames through view port).
The correct ame pattern should be viewed by looking through the view port in front of the unit cover.
1
2
1
2
3
3
TOP
VIEW
UNDERSIDE
VIEW
1) Termocouple
2) Ignition electrode
4
4
3) Pilot
4) Gas outlet
B
A
A = minimum ames
B = maximum ames

Drolet-DG04905 19
PILOT FLAME
The pilot ame must to be always in a stable
condition, correctly touching the ame relavator to
keep the appliance lit on, if not, call your technical
service or your gas supplier
TO REMOVE MAIN BURNER FOR INSPECTION
AND CLEANING
NOTE: The stove and all components must be inspected
at least annually by a qualied service technician.
This should include the burner, heat exchanger, and
vent system. Be sure that the ow of combustion and
ventilation air are not obstructed.
1. Remove outer casing.
2. Disconnect gas supply to valve.
3. Remove the screws holding burner door to
heat exchanger and lift out complete burner.
4. After inspecting burner, place back into heat
exchanger. Be sure door gasket is not damaged
and will effect a proper seal or pilot outage will
occur.
5. Tighten screws holding burner door to heat
exchanger.
6. Connect gas supply back to the pilot.
7. Reassemble the casing.

Drolet-DG0490520
GAS CONVERSION INSTRUCTION
The room heater is suitable, and it is possible to
change, in every moment ,the conguration from a
type of gas to another type, i.e. from Gas "E" (LPG)to
Gas "A"(LNG).
To make this conversion follow the below instructions,
step by step:
- Disconnect the electrical power supply.
- Remove the jacket.
- Shut off the gas supply and disconnect the pipes.
PILOT BURNER INJECTOR REPLACEMENT
1. Unscrew the M10x1 collar (1) from the pilot
burner fitting, extract the gas pipe(2) with the
injector (6) still attached to it.
2. Replace the injector(6) with the one for the
new gas type.
IMPORTANT: Make sure that the groove on the head
of the injector (6) ts onto the key on the gas outlet (3).
3. In reverse order, replace the pipe with the
injector connected to it, taking care not to
dislodge or crush it at the beginning , clamping
the collar manually, at the end, complete this
operation with a wrench. The seal of the
injector is mechanic, so there is no need for
a gasket.
31
2
6
(LPG)
Model
DV30
main burner
pilot
(LNG)
1,65 1,05
mm
Ø
0,42 0,19
Ø
DV45
main burner
pilot
1,98 1,25
Ø
0,42 0,19
Ø
WARNING: Conversion must be done by a qualied service technician, using only the orignal parts attached
to the appliance.
MAIN GAS BURNER INJECTOR REPLACEMENT
1. Unscrew the collar (4, 3/8” F) from the MAIN
BURNER Injector mount fitting;
2. Unscrew the injector mount fitting from the
injector itself;
3. Unscrew the injector (5) and replace it with the
new one. Thread it on by hand and only then tighten it
down with a wrench. The seal of the injector and of the
injector mount tting is mechanic, so there is no need for
a gasket.
4. Check that the value stamped on the injectors match those in the table.
5. Restore the burner unit in reverse order.
6. Make the adjustments indicated in Chapter ADJUSTMENTS; also check that the gas fittings on
thepipe running from the gas cock to the burner unit are tight.