DSE MV Series User manual

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 1
MV Series - MDVR for vehicles
AHD video recorders
Installation manual
How to install the system How to
configure the functions
How to connect via web with CMSV6
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 2
Contents of the manual
MV video recorders are vehicle DVRs suitable for CVBS and AHD analog cameras up to 2MP (1080P). They are ideal in combination
with our vehicle cameras.
This manual explains how to install cameras and video recorder, how to make basic adjustments and how to connect from a computer
via the WEB for models that include this possibility.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 3
Package Contents
The MDVR you purchased is vehicle video recorder. The package includes:
1 - MDVR VCR
2 - 3G ANTENNA, WiFI ANTENNA, GPS functions) (only in models with these
3 - 4 CAMERA ADAPTER CABLES (Minidin - BNC / DC)
4 - 1 ADAPTER CABLE FOR CVBS MONITOR (Minidin - BNC / DC)
5 - 1 RJ45 NETWORK ADAPTER CABLE (only for models with this function) 6 - POWER CABLES AND
ACCESSORIES
7 - REMOTE CONTROL
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 4
SD card installation
All DVRs in this range are designed to be able to record on SD card. To access the SD card slot you must first unlock the protective
cover with the included lock key.
MDVRs accept SD cards, or microSD cards with adapter, up to 256GB in capacity.
Hard Disk Installation
Hard disk DVRs allow you to install a 2.5 "Hard Disk inside
Once the hard disk has been inserted, it is important to close the lock of the removable drawer with the appropriate key.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 5
Power connection
All DVRs in this range accept power from 8 to 36VDC to adapt to any medium. The power cable is included to connect to the vehicle's
electrical panel to receive power from the battery.
For the DVR to start up, positive must be applied to the red (IN +) and yellow (ACC) cables at the same time and negative to the
black (GND) cable.
As a rule, the DVR is connected so that it switches on and off automatically when switched on by connecting the red cable to the
battery positive and the yellow cable to the ACC output of the vehicle control unit, according to the following diagram
If, on the other hand, you want the DVR to be always active or to switch on based on its time schedule, you can use the
following scheme
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 6
The power cable is equipped with a protection fuse.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 7
Adapter cables
The MDVRs use MiniDIN aviation type connectors because they are compact and equipped with a fixing ring which makes them
protected against vibrations. To connect cameras, monitors, etc. the MDVRs are supplied with a set of adapter connection cables with
DC (12VDC power supply), BNC (Video) and RCA (Audio) terminals. You will use these cables to connect the cameras and monitor.
Adapter cables are also included for network connection (where provided) and for relay inputs and outputs.
If you want to reduce the overall dimensions and maximize the resistance to vibration, instead of using adapter cables, you can buy
female 4-pole mini din connectors and solder the cables directly to the connector following the following pin-out
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 8
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 9
LEDs and connections - MV-41
PWR - Power LED ERR - GPS system
error LED - GPS status LED
VLS - Video lost SD - SD
card status NET - Not used
IR - USB remote control receiver -
Backup port
DC 8-36V - Connect red to battery positive, black to battery negative and yellow to the ACC line of the electrical panel
A / V IN1 A / V IN2 - Inputs for video / audio cameras. Connect the cameras here with the included cable which provides a DC connector
to power the 12VDC camera, a video BNC and an RCA for any audio. MDVRs support CVBS analog cameras, AHD720P. This model
does not support AHD1080P.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 10
V IN3 V IN4 - Inputs for video-only cameras. Connect the cameras here with the included cable which provides a DC connector to power
the 12VDC camera, a video BNC and an RCA that you will leave unused.
A / V OUT - Audio video output for CVBS monitors. Connect the monitor here with one of the adapter cables which provides a DC
connector to power the monitor at 12VDC, a video BNC and an RCA for any audio.
I / O - Here you can connect the supplied cable which allows you several auxiliary connections
WHITE SENSOR 1,2,3 you can connect 3 alarm inputs. These are voltage inputs that are activated by sending a voltage of 5 or 12VDC.
In configuration you can establish whether the alarm is determined by the presence of voltage (HIGH) or by the absence of voltage
(LOW). GRAY SENSOR OUT you can connect an alarm output between the gray cable and GND PURPLE BROWN - RS232 to
connect special devices
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 11
LEDs and connections - MV-42
PWR - GPS power LED - GPS status
LED
REC - Registration
NET - IR network connection - Remote
control receiver
SIM - Insert the data SIM for 3G / 4G SD connection - Insert the SD card or
miniSD card with USB adapter - USB socket for backup
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 12
DC 8-36V - Connect red to battery positive, black to battery negative and yellow to the ACC line of the electrical panel
A / V IN1 2 3 4 - Inputs for video / audio cameras. Connect the cameras here with the included cable which provides a DC connector to
power the 12VDC camera, a video BNC and an RCA for any audio. MDVRs support CVBS, AHD720P and AHD1080P analog cameras.
A / V OUT - Audio video output for CVBS monitors. Connect the monitor here with one of the adapter cables which provides a DC
connector to power the monitor at 12VDC, a video BNC and an RCA for any audio.
LAN - Network port for connecting to a LAN with the included RJ45 adapter cable. GPS - Connector for GPS antenna
3 / 4G - Connector for GPS
WIFI - HMIC WiFi antenna connector - Not used
I / O - Connect the supplied cable for connecting inputs and outputs
WHITE SENSOR 1,2,3,4 you can connect 4 alarm inputs. These are voltage inputs that are activated by sending a voltage of 5 or
12VDC. In configuration you can establish whether the alarm is determined by the presence of voltage (HIGH) or by the absence of
voltage (LOW).
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 13
GRAY SENSOR OUT 1,2 you can connect 2 alarm outputs between the gray cable and GND PURPLE BROWN -
RS232 to connect special devices
YELLOW ORANGE - RS485 for the control of motorized cameras RED - 12VDC power supply
output
RED - 5VDC power supply output WHITE - ADC
analogue input 1 WHITE - ADC analogue input 2
Avoid Hot Swap Connections
In the installation of this MDVR it is necessary to avoid Hot Swaps, that is the modification of the connections after accessing the MDVR.
This is because the MDVR has to find all the elements of the system present during the start-up phase.
For this reason when installing these MDVRs, connect all cameras and monitor first. Also insert the SD card, the Hard Disk and possibly
the SIM. Only after connecting all the elements can you power up and turn on the MDVR with the certainty that it works well.
If, on the other hand, you turn on the MDVR and only then connect cameras or accessories, the MDVR may not correctly manage the
elements you have connected.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 14
Remote controller
The MDVRs do not have a mouse like the desktop DVRs and are controlled with the supplied remote control. The remote control
receiver is on the front of the MDVR, next to the signaling LEDs.
Key Function Image
[0-9] [0-9]: During settings you can use these keys to enter
numbers. In playback you can use the 1-4 keys to bring the
corresponding channel to full screen and the 0 key to return
to 4-channel multivision.
Key to cancel while typing Key to exit the menu
Confirms the entered data and also serves as a PLAY key. The arrows
are used to move in the MDVR menu. The left and right arrows are also
used to adjust the speed during playback.
Fast forward, 2x / 4x / 8x / 16x press [Play] to return to normal
speed
Fast reverse 2x / 4x / 8x / 16x press [Play] to return to normal
speed
Button to enter the dot of the IP addresses
[OF THE]
[RETURN]
[ENTER]
,▲, ,
This button captures the photo of the 4 cameras on the
screen
PTZ control
Enters the TEST mode useful for Debug Information
+
Others Keys without function
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 15
Access to the menu
To access the configuration, press the MENU button on the remote control.
The factory passwords are:
USER ACCESS: 888888
ADMINISTRATOR ACCESS: 999999
The aesthetics of the menu may vary according to the models, keeping the functions unchanged.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 16
Playback
The playback button allows you to review the recordings
You can search the disk (HDD) or SD card (SD) by indicating the date and time. You can also select
the type of recording (ALARM or ALL) Press ENTER to play the video.
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 17
Preview
The preview button allows you to review the photos taken by the MDVR
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 18
Settings
The settings button accesses the settings section which is divided into 6 sections
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 19
Settings / Basic
In the Settings / Basic section there are the general settings of the MDVR
BASIC / TIME
Here you set the time of the MDVR by setting it manually or by selecting automatic synchronization with the GPS (if
included in the model)
BASIC / PWD
Here you set the login password
The MDVR manages 2 passwords: USER (USER, factory 888888) and Administrator (ADMIN factory 999999)
USER - Can see the recordings, but not change the settings
DSE SRL - ITALY - WWW.DSE.EU

INSTALLATION MANUAL
MV SERIES - MDVR for vehicles
Page: 20
ADMIN - Has access to all functions
BASIC / USER
Here you set the data of the MDVR to identify it easily. In other parts of the program you can use this data to identify the device.
ID - Identification number of the MDVR
GPS - The GPS mode to be kept on GPS LICENSE - Enter the vehicle
license plate
DRIVER - Enter the driver's name
COMPANY - Insert the eventual name of the organization
BASIC / MIRROR
Here you can flip the camera image
VD - Vertical image flip. To be used if the camera is mounted upside down
LR - Horizontal Image Flip. To be used if the camera is shooting in the reverse direction.
DSE SRL - ITALY - WWW.DSE.EU