DSE 7560 User manual

DEEP SEA ELECTRONICS
7560 INSTALLATIO N INSTRUCTIONS 053-054
ISSUE 4
ACCESSING THE FRONT PANEL CONFIGURATION EDITOR
.
•Press the Stop/Reset and Info buttons simultaneously.
•If a module security PIN has been set, the PIN number request is then
shown :
•Press (up) or (down) to adjust it to the correct value.
•Press (right) when the first digit is correctly entered. The digit you have just entered will now
show ‘#’ for security.
• Repeat this process for the other digits of the PIN number. You can press (left) if you need to
move back to adjust one of the previous digits.
• When is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
EDITING A PARAMETER
•Enter the editor as described above.
•Press the left or right buttons to cycle to the section you wish to view/change.
•To edit the parameter, press to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
•Press the up or down buttons to change the parameter to the required value.
•Press to save the value. The parameter ceases flashing to indicate that it has been saved.
•To exit the editor at any time, press the button.
Deep Sea Electronics Plc.
Tel:[phone]
Fax: [phone]
LO CALL (from UK BT landlines) :
Telephone [phone]
Email: [email protected]
Web:
www.deepseaplc.com
Deep Sea Electronics inc.
Phone: [phone]
Fax: [phone]
TOLL FREE (USA only) : Tel: [phone]
Email: [email protected]
Web: www.deepseausa.com
Deep Sea Electronics Plc.
(Far East)
Tel:[phone]
Fax: [phone]
Email: [email protected]
Web: www.deepseaplc.com
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security.
NOTE: More comprehensive module configuration is possible using the 75xx series PC
configuration software. Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration.
TYPICAL WIRING DIAGRAM

ADJUSTABLE PARAMETERS.
Front Panel Configuration Editor (Factory default settings are shown in bold italicised text)
Section
Parameter
as shown on
Values
Timers
Mains Transient Delay 0 -10s (2s)
Start Delay 0– 60m (5s)
Transfer Delay 0– 10s (0.7s)
Return Delay 0– 60m (30sa0
Low battery Delay 0– 10m (1m)
High battery Delay 0– 10m (1m)`
Mains
Mains Under Voltage Alarm 50V 360V ph N (184V)
(184V)(184V)
(184V)
Mains Over Voltage Alarm 50V 360V ph N (276V)
(276V)(276V)
(276V)
Mains Under Frequency 0Hz 75Hz (45Hz)
(45Hz)(45Hz)
(45Hz)
Mains Over Frequency 0Hz 75Hz (55Hz)
(55Hz)(55Hz)
(55Hz)
System
Plant Battery Under Volt Alarm 0 40V (10V)
(10V)(10V)
(10V)
Plant Battery Over Alarm 0 40V (30V)
(30V)(30V)
(30V)
Misc
Language English, Other
Alternative Frequency Enable Disable
DisableDisable
Disable
Alternative Voltage Enable Disable
DisableDisable
Disable
AC System
3 phase 4 wire
3 phase 4 wire3 phase 4 wire
3 phase 4 wire
Single phase 2 Wire
3 phase 3 wire
2 phase 3 wire L1 & L2
3 phase 4 wire ED
2 phase 3 wire L1 & L3
Contrast
 l 
Date and Time dd mmm yyyy hh:mm
Auto Scroll Time 0 10s (2s)
(2s)(2s)
(2s)
Mains CT Primary Rating 5A 6000A (600A)
(600A)(600A)
(600A)
Mains CT Secondary Rating 1A, 5A (5A)
(5A)(5A)
(5A)
Load Ramp Rate
0.1%
100% (
2.0%)
2.0%)2.0%)
2.0%)
(% per sec)
ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR
•The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.
•Press and hold the button to enter the running editor.
EDITING A PARAMETER
•Enter the editor as described above.
•Press the left or right buttons to cycle to the section you wish to view/change.
•Press the up or down buttons to change the parameter to the required value.
•To save paremeters scroll to `save changes and exit followed by the down buttton
•To cancel changes scroll to `Abandon changes and exit followed by the down
button
ADJUSTABLE PARAMETERS (Running editor)
Running Editor
Section
Parameter as shown on display Factory Settings
DISPLAY Contrast
 l 
Language English
Load power factor %
Load parallel power %
Enable commissioning screens No
Voltage adjust
(manual mode only engine running bus breaker open)
Raise Steady Lower
Fr
eq
uency adjust
(manual mode only engine running bus breaker open)
Raise Steady Lower
Enable mains decoupling No
Abandon changes and exit
Save changes and exit
DIMENSIONS
240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)
PANEL CUTOUT
:
220mm x 160mm (8.7” x 6.3”)