(1) Modem Dialup User:
Pick up the handset and press on your to connect
to the Internet. When you see a static @ sign on the LCD screen,
it means it has connected to the Internet. Please wait until you
hear the ready tone.
Congratulations! You've successfully completed the settings. You can start to talk to anyone over Internet/Intranet by following the instructions below.
Note: If you see a static @ sign on the LCD screen, that means the has connected to the Internet successfully. If you see a flashing @ sign on the
LCD screen, it means the is not connected to the Internet.
Note: After the connects to the Internet, you can press on the telephone keypad to display your ITSP account balance on the screen.
For Static IP
(a) When the IP TYPE "Static IP" is selected, pick up the telephone handset and press to access to IP ADDRESS. Press to edit this item.
(b) Use the telephone keypad to input one of the available IP addresses. Press again to save and exit.
(c) Press to go to GATEWAY IP and press to edit this item.
(d) Input the gateway IP address with your telephone keypad. Please check your ISP or network administrator for the information. Press to save and exit.
(e) Press to go to SUBNET MASK. Press to edit this item.
( f ) Input your subnet mask and then press to save and exit. Please check with your ISP or network manager for the information.
(g) Press again to go to OFFHOOK MODE. Press to edit this item and press or to select PSTN or I-PHONE. Press again to save
and exit.
(h) Now you've entered Internet connection information. Press several times until you see EXIT TO MAIN. Press to save and exit. The system
will automatically reload the Ethernet.
For DHCP
(a) When the IP TYPE "DHCP" is selected, pick up the telephone handset and press to go to OFFHOOK MODE. Press to edit this item and
press or to select PSTN or I-PHONE. Press again to save and exit.
(b) Now you've entered Internet connection information. Press several times until you see EXIT TO MAIN. Press to save and exit. Press
several times until you see EXIT SETUP and then press to exit.
For ADSL PPPoE
(a) When the IP TYPE "ADSL PPPoE" is selected, pick up the telephone handset and press to go to ADSL PPPoE ID. Press to edit this item.
(b) Use the telephone keypad to input the ADSL PPPoE ID and then press again to save and exit.
(c) Press to go to PPPoE PASSWORD. Press to edit this item. After you input the password, press to save and exit.
(d) Press again to go to OFFHOOK MODE. Press to edit this item and press or to select PSTN or I-PHONE. Press again to save
and exit.
(e) Now you've entered Internet connection information. Press several times until you see EXIT TO MAIN. Press to save and exit. The
will automatically reload the Ethernet.
(1) Press and hold button for 2 seconds and the screen will display your working mode. Pick up the telephone handset and press several times
until the screen shows ITSP SETUP.
(2) Press and the screen will display ITSP ACCOUNT. Press again to edit this item.
(3) Use your telephone keypad to enter the ITSP account number. Press on your to save and exit. You must have a valid ITSP account in order
to
make
a
Device-to-Phone
call.
If
there's
no
balance
remained
in
your
ITSP
account,
you
can
contact
your
local
dealer
or
e-mail
to
[email protected]. (4) You have now entered required information for Device-to-Phone mode. Press several times until you see EXIT TO MAIN. Press to save and exit.
07GS97QE.A © 2007 DSG Technology, Inc. All rights reserved.
4. Input Required Information for Device-to-Phone Mode
Operation Mode
Ethernet User:
First be sure you see a static @ sign on the LCD screen. Pick up the handset directly and you will hear the ready tone. If you set the "OFFHOOK
MODE" as "PSTN", you have to press first and wait for the ready tone before you call.
(2) Now you can start to dial any long-distance or international telephone numbers. No matter where you are, the dialing rules of long-distance calls or
international calls are the same as follows:
Note: If you find any serious delay or interruption during the conversation while using , it is an indication of congested data transmission between
ISPs. You can hang up and try to call again later to see if the transmission improves. If you have any further question, please refer to the
Operation Manual or visit www.dsgtechnology.com for more details.
Device-to-Phone
123
456
789
ň
0
Ł
Destination Phone
VoIP Gateway PSTN
Please refer to the following examples.
[Country Code][Area Code][
Telephone Number]
++
To make an international call from any country to Japan
++
[Japan Country Code]
81
[Japan Area Code]
3
[Japan Tel. No.]
55551234
To make a long-distance call within U.S.
++
[USA Country Code]
1
[USA Area Code]
212
[Telephone Number]
5551234
