DSP SEED-XDS560v2 User manual

SEED-XDS560v2 JTAG Emulator User’s Guide
2011-05
DSP Development Systems

SEED-XDS560v2 JTAG Emulator
Installation User’s Guide
http://www.seeddsp.com
Version: A
2011.7

IMPORTANT NOTICE
SEED Electronic Technology Ltd reserves the right to make changes to its products or to
discontinue any product or service without notice. Customers are advised to obtain the
latest version of relevant information to verify that the data being relied on is current before
placing orders.

3
Preface
Read This First
About This Manual
This document describes the installation and operations of the SEED-XDS560v2 Emulator.
The SEED-XDS560v2 Emulator is used for the development platform of Texas Instruments
DSP processor. The SEED-XDS560v2 Emulator is a high speed emulator and adapts to all
series of Texas Instruments DSP processor.
Warranty
The warranty period for all hardware and software products manufactured by SEED
International is one year after shipment. SEED International guarantees free of charge repair
or replacement for the manufacturer caused damaged products during warranty period.
Software updates will be sent free of charge to the customer during warranty period.
Trademarks
SEED is trademark of SEED International.
TI, XDS510, XDS560 are trademarks of Texas Instruments.

4
If You Need Assistance …

 Web：http://www.seeddsp.com/eng

 Beijing Headquarter
Address: Unit 1201, Pan-Pacific Plaza, No. 12A,
South Street Zhongguancun, Haidian District, Beijing, P.R.China
Zip: 100081
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
To help us Improve Our Documentation …
If you would like to make suggestions or report errors in documentation, please email us. Be sure
to include the following information that is on the title page: the full title of the book, the
publication data, and the literature number.
Email: [e-mail]

5
Caution
Minimizing Personal Injury:
To minimize the risk of personal injury, always turn off the power to your PC and unplug the
power cord before connect the SEED-XDS560v2 JTAG Emulator
Minimizing Electrical Shock and Fire Hazard:
To minimize the risk of electric shock and fire hazard, be sure that all major components that you
interface with SEED devices are limited in energy and certified by one or more of the following
agencies: UL, CSA, VDE, or TUV.

6
Contents
Read This First .......................................................................................................................3
About This Manual...................................................................................................3
Warranty.................................................................................................................3
Trademarks .............................................................................................................3
If You Need Assistance …..........................................................................................4
To help us Improve Our Documentation ….................................................................4
Caution..................................................................................................................................5
Contents................................................................................................................................6
Chapter 1...............................................................................................................................8
SEED-XDS560v2 Instruction ....................................................................................................8
1.1 Product Outline....................................................................................................8
1.1.1 SEED-XDS560v2 Hardware Features ...........................................................8
1.1.2 SEED-XDS560v2 Software Features.............................................................8
1.2 Product Support.................................................................................................12
Chapter 2.............................................................................................................................13
SEED-XDS560v2 Driver Installation .......................................................................................13
2.1 CCS4 Installation ................................................................................................13
2.2 XDS560v2 Driver Installation...............................................................................13
2.2.1 SEED-XDS560v2 Driver Installation ...........................................................13
2.2.2 Install emulator hardware devices............................................................17
Chapter 3.............................................................................................................................20
SEED-XDS560v2 Usage .........................................................................................................20
3.1 XDS560v2 USB debug .........................................................................................20
3.1.1 Hardware connection ..............................................................................20
3.1.2 Software Debugging ................................................................................20
3.2 Network Debug..................................................................................................24
3.3.1 Hardware connection ..............................................................................24
3.3.2 Software debugging ................................................................................24
Chapter 4.............................................................................................................................28

7
Cautions when using SEED-XDS560v2 ...................................................................................28
Appendix A..........................................................................................................................29
JTAG Adaptor Introduction...................................................................................................29
A.1 SEED-XDS560v2_6014_v0.3......................................................................................29
A.2 SEED-XDS560v2_6020_v0.3......................................................................................30

8
Chapter 1
SEED-XDS560v2 Instruction
1.1 Product Outline
SEED-XDS560v2 fully supports XDS560v2 from Texas Instruments, support real-time
emulation, debugging and system trace function. SEED-XDS560v2 have two kinds of
communication interface: USB2.0 High speed (480MB/S) and Ethernet RJ45 (10/100M). It
supports CCS4.1.3 and versions above, suitable for all the platform classes of TI including DM816x
and C66xx.
1.1.1 SEED-XDS560v2 Hardware Features
Support traditional JTAG protocol IEEE 1149.1 and IEEE 1149.7
Support high speed USB2.0 and 10/100Mbit Ethernet host interface
Support System Trace
Support TI C2000/C5000/C6000/ARM/ARM Cortex/Sitara/OMAP/DaVinci classes
Support multi-CPU debugging
Unique MAC address
Configurable IP addresses
Programmable TCLK: up to 64MHZ
MIPI standard 60-pin HSPT
Support JTAG from +1.2 to +4.1 V
High-speed anti-interference emulation cables
1.1.2 SEED-XDS560v2 Software Features
Support CCS4.1.3 and versions above
Support Windows XP/Vista/Win7
1.1.3 SEED-XDS560v2 Accessories introduces

 XDS560v2 Emulator

9
Figure1 XDS560v2 Emulator

 Ethernet port, USB interface and power interface on one side of the Emulator

 Six LED indicators on SEED-XDS560v2 : COM-LED1, COM-LED2, COM-LED3, EMU-LED1,
EMU-LED2, EMU-LED3 (from left to right)
Table1 LED Information
LED
Color
Description
COM-LED1
Red
XDS560v2 Ready
COM-LED2
Red
Shows XDS560v2 FPGA programmed state
COM-LED3
Green
Shows XDS560v2 system Boot Activity
EMU-LED1
Green
Shows target to XDS560v2 Trace Activity
EMU-LED2
Red
Shows XDS560v2 to host Activity
EMU-LED3
Green
Show connectivity via CCS when at on a state

10

 JTAG Adaptor (Do not plug or unplug the adaptor then it is at work)
SEED-XDS560v2_6014_v0.3
This adaptor is provided for customers’ 14pin JTAG target board:
Front Back
When customer’s JTAG is 14pin, please use the front of the Adaptor to plug
in the following JTAG at the end of emulator cable, then plug the back of the
Adaptor into your target board.
SEED-XDS560v2_6020_v0.3
This kind of Adaptor is designed for 20pin JTAG target boards:
Front Back
When your target board is 20-pin JTAG, after plugging the front of the Adaptor
into the JTAG at the end of the emulator cable, then plug the back of the Adaptor
into your target board.

 USB A/B Cable
There exists an USB interface on SEED-XDS560v2, when you are debugging by USB or
you are configuring emulator IP, please connect the A-end of the USB Cable with the
USB port on the PC, B-end is used to connect USB port on the emulator

11

 Ethernet Cable
There exists an Ethernet port on SEED-XDS560v2, when you are debugging by network,
please connect the net port on 560v2 and PC (or Router) with this Ethernet cable.

 5V Power
When powering the emulator, please connect the power port on the emulator with the
right side 5V Power

 CD ROM
This CD ROM includes:
SEED-XDS560v2 Driver.exe
SEED-XDS560v2 JTAG Emulator Installation User's Guide
SEED-XDS560v2 Configuration Tools Users' Guide

12
Note: SEED is updating the software time to time, please pay attention to the news on
www.seeddsp.com/eng to upgrade your driver.
1.2 Product Support
Please contact your local distributor to get directly product support
You can also send email to SEED International directly: [e-mail]

13
Chapter 2
SEED-XDS560v2 Driver Installation
The minimum system requirement for installing XDS560v2:
Windows XP Professional edition
Code Composer Studio™V4.1.3.00038
Note
SEED-XDS560v2 only supports Code Composer Studio with CCS 4.1.3.00038 and version
above
Before installing driver, please make sure you have installed CCS already.
The manual take CCS4.2.3.00004 as an example.
Caution
To minimize the risk of personal injury, always turn off the power to your PC and unplug
the power cord before connecting the SEED-XDS560v2 JTAG Emulator
To minimize the risk of electric shock and fire hazard, be sure that all major components
that you interface with SEED devices are limited in energy and certified by one or more of the
following agencies: UL, CSA, VDE, or TUV.
2.1 CCS4 Installation
2.2 XDS560v2 Driver Installation
Please install the driver in strict accordance with the following step.
2.2.1 SEED-XDS560v2 Driver Installation
1. Click “SEED-XDS560v2 Driver.exe “, start installation.

14
2. Click “Next “.
3. Choose “I access the terms of the license agreement “, click “Next “.

15
4. Choose CCS Installation Path, choose “Next “(the default install path is recommended)
5. Click “Install “.

16
6. Install driver
7. Click “Finish “, finish the installation of driver.

17
2.2.2 Install emulator hardware devices
1. Use the USB Cable to connect the emulator with the computer;
2. Power the emulator with the 5V power, COM-LED3 light turns green, XDS560v2 starts loader.
3. Please wait until the COM-LED3 green light is off and the lights “COM-LED1” & “COM-LED2”
turn red, that means loader finish, PC will display “found new hardware “.
4. Choose “No, not this time “, choose “next“.

18
5. Choose “Install the software automatically (Recommended)“, click “Next “
6. PC is installing emulator driver.
7. Click “Finish “, the emulator finish driver intallation.

19
8. Open “Device Manager “. Windows will confirm that the SEED-XDS560v2 has been installed
successfully shown in following figure:
9. Unplug the emulator power.